User Manual

ManualsBrandsMidmark ManualsSteam Sterilizermidmark M11 Steam Sterilizer

Applies to Models:

M9 / M11 / M3

QC1 -01

QC3(R) -01

QC6(R) -01

Sterilizer and QuickClean™ Startup Procedures

003-10351-00 Rev. AA2 (1/7/22)

M9 / M11 Steam Sterilizer

Note: These instructions outline basic startup procedures. For all technical information

and user guides, visit our technical library at technicallibrary.midmark.com

Equipment Alert

Use distilled water or water that meets the

water purity specifications referenced in

your Users Guide. Failure to comply may

result in sterilizer malfunction and/or premature

failure due to excessive corrosion.

Door

Gasket

Dam

Gasket

Chamber

Tray Rack

Tray Plate

Trays

Cleaning.

A) Wash the exterior of the sterilizer according to your facility’s

procedure for clinical contact surfaces, noting the following:

(Use only quaternary disinfectants to disinfect unit.

Staining, pitting, discoloration, or softening could occur if

phenolic, iodophor, or glutaraldehyde-based disinfectant is

used on plastic surfaces of the unit. Also, use of alcohol or

aerosol spray cleaner / disinfectant containing substantial

amounts of alcohol in the formula can damage the faceplate).

B) Wring excess solution from cloth.

C) Using soft cloth, wipe all external surfaces.

D) Follow the instructions provided with the cleaner / disinfectant

used regarding rinsing and drying of external surfaces.

E) Examine gaskets for possible damage.

F) Clean gaskets and mating surfaces with a damp cloth.

G) Wash trays, rack, plate, and inside of chamber with mild soap

or Speed-Clean and distilled water or water that meets the

 referencedwaterpurityspecications.

Summary of content (12 pages)

PAGE 1
Applies to Models: Sterilizer and QuickClean™ Startup Procedures M9 / M11 / M3 QC1 -01 QC3(R) -01 QC6(R) -01 Note: These instructions outline basic startup procedures. For all technical information and user guides, visit our technical library at technicallibrary.midmark.com M9 / M11 Steam Sterilizer Equipment Alert Use distilled water or water that meets the water purity specifications referenced in your Users Guide.
PAGE 2
M9 / M11 Steam Sterilizer - continued Check filters. Visually check to ensure filter screens are in place, both the back and bottom of your sterilizer chamber. Water Level Sensor Air Filter Screen Fill / Vent Filter Screen Equipment Alert Install tray rack / plate with angled end of plate toward the back of the chamber. Do not allow plate to contact the water level sensor. Tray Rack Install tray rack / plate, and trays. A) B) C) D) Insert the tray rack into the tray plate.
PAGE 3
M9 / M11 Steam Sterilizer - continued Fill reservoir. A) Open door to unit. B) Pour distilled water into fill opening until water level reaches the top of the fill level label on the water level indicator tube. Equipment Alert Use distilled water or water that meets the water purity specifications referenced in your Users Guide. Failure to comply may result in sterilizer malfunction and/or premature failure due to excessive corrosion. M9-04x / M11-04x Display Shown Connect power cord.
PAGE 4
M9 / M11 Steam Sterilizer - continued Test Cycle Run a test cycle to ensure that your system is running properly. Equipment Alert The sterilizer will not operate unless the door is closed and latched properly. Close and latch the door. A) Lift the door handle, then push the door closed. B) While pushing in on the door, slide the door handle down to engage the latch. Select cycle. Press the desired cycle button on the display panel.
PAGE 5
M3 Sterilizer Cleaning. A) Wash unit according to your facility’s procedure for clinical contact surfaces noting the following: (Use only quaternary disinfectants to disinfect unit. Staining, pitting, discoloration, or softening could occur if phenolic, iodophor, or glutaraldehyde-based disinfectant is used on plastic surfaces of the unit. Also, use of alcohol or aerosol spray cleaner / disinfectant containing substantial amounts of alcohol in the formula can damage the faceplate.).
PAGE 6
M3 Sterilizer - continued Note External Condensing Tank is not needed if M3 is connected to the VistaCool direct-to-drain thermal reduction system. Equipment Alert The tank hose must be properly connected (and not kinked). Improper connection will cause water / steam leaks or a sterilizer malfunction if water flow to the tank is restricted. 0 Power Cord Tank Hose 0 Connect the condensing tank. A) If connected, disconnect sterilizer power cord. B) Push tank hose into compression fitting on lid.
PAGE 7
M3 Sterilizer - continued Connect the condensing tank - continued. F) Place tank on a level surface, preferably below the sterilizer but in no case should it be higher than the sterilizer support surface. G) Connect sensor plug. H) Plug power cord into receptacle on back of sterilizer. I) Plug power cord into a properly polarized and grounded receptacle rated for a minimum of 15 amps. A dedicated circuit only used for the sterilizer is recommended. 0 Power Cord Sensor Plug 0 Note Clearance.
PAGE 8
M3 Sterilizer - continued Fill reservoir. Pour one (1) gallon of distilled water into fill port. Do not fill above lower lip of fill port. Lower Lip Equipment Alert Use distilled water or water that meets the water purity specifications referenced in your Users Guide. Failure to comply may result in sterilizer malfunction and/or premature failure due to excessive corrosion. Power Switch The power switch must be ON (I) for the sterilizer to operate. 0 OFF (O) 0 ON (I) 0 © 2020 Midmark Corp.
PAGE 9
M3 Sterilizer - continued Priming the Water Pump Put the sterilizer into User Diagnostics Mode to prime the water pump. To activate User Diagnostic Mode. A) Turn Power Switch OFF (O). B) Press and hold the button. C) Turn Power Switch ON ( I ). D) Press the button when the display shows “USER DIAGNOSTIC”. To prime the sterilizer pump. A) Put the unit in User Diagnostic Mode. B) Press the button to start the pump priming progress.
PAGE 10
QuickClean™ Units Drain Valve Closed Drain Valve Open Close drain valve. Ensure that the drain valve is in the Closed position. Before Operating the QuickClean™ A) Clean unit and wipe out tank. “Clean by wiping with a damp soapy cloth and rinse.” B) Pour water into the bath so that it reaches the liquid level sensor, but do not exceed the maximum fill level. Follow cleaning agent’s recommendations on water temperature. Cleaning efficacy can only be guaranteed if the water temperature is at least 70 F.
PAGE 11
QuickClean™ Units - continued Degas Cycle Degas • Degas cycle will allow optimal ultrasonic activity by removing gases present in ordinary tap water. • The time needed to degas the liquid will vary depending on the amount of gas present in the liquid and the quantity of water in the tank. • A degas period of 5 to 10 minutes is recommended.
PAGE 12
QuickClean™ Units - continued Test Cycle Run a test cycle by performing a “Foil” test to ensure that your system is running properly. Perform the “Foil” Test Purpose: Used to determine the efficiency of an Ultrasonic Cleaner. • Quarterly testing of the ultrasonic cleaner to assure that it is operating properly is recommended. • Testing should also be performed whenever deterioration in the cleaner performance is suspected.