G10 ” Instruction guide PMR446 TRANSCEIVER |
Index Programming software (optional) 2 Content 2 Main characteristics 3 Coverage/Range 3 Main controls and parts of the radio 4 Operations 6 Power on/off and volume adjustment 6 Transmission 6 Monitor 6 Scan 6 Squelch 7 Battery recharge 7 Maintenance 8 Technical specifications Troubleshooting Midland G10 instruction guide 9 10 |1
Thanks for choosing Midland! G10 is a portable transceiver that is free use in almost all European countries. For further information, we suggest you look at the “Restrictions on the use” chart. Midland G10 is a multi-task PMR446 transceiver.
Main characteristics t t t t t t t t t PMR446 Transceiver Output power: ≤ 500mW ERP Channel spacing: 12.5KHz Scan Vocal tuning Roger Beep Battery save Monitor Squelch COVERAGE/RANGE The maximum range depends on terrain condition and is obtained during use in an open space. The only limitation to maximum possible range are environmental factors such as blockage caused by trees,buildings, or other obstructions. Inside a car or a metallic constructions, the range can be reduced.
Main controls and parts of the radio 1. 2. Antenna Encoder: rotate clockwise or counter-clockwise to select the desired channel 3. Power/volume knob- turn clockwise to power on and increase the volume level. Turn counter-clockwise to decrease the volume level and power off. 4. Speaker 5. Built-in microphone 6. Led indicator: RED: TX; GREEN: RX. 7. PTT: push this button to transmit, release it to receive. 8. Function key 1: hold down this button to activate the Monitor function. 9.
1 2 3 6 4 PTT PTT 7 8 5 Midland G10 instruction guide SP SP MIC MIC 10 9 |5
Operations Power on/off and volume adjustment Rotate the Power/Volume knob clockwise to turn the radio on. Rotate the control clockwise /counter-clockwise to adjust the volume level as you prefer. To turn the radio off, rotate the control counter-clockwise till hearing a mechanical “click”. Transmission To communicate, all radios in your group must be set to the same channel.
ming software. To enable the Scan function, all 16 channels must be programmed. If you turn on the radio on channel 16, the scanning will automatically start. Whenever any signal is detected, the scanning will stop on a busy channel. If the PTT is pressed, you will transmit on the latest busy channel. Channel 16 is the priority channel, therefore if you don’t pick up any signal when you press PTT, the radio will transmit on channel 16.
! Using a different battery charger other than the one specified can cause damage to your device or may even cause explosions and personal injuries. The Battery power saving feature enables a reduction in consumption of up to 50%. If it has been set, it automatically activates when the transceiver does not receive any signal for more than 5 seconds in order to save the battery life. Power saving can be disabled only through Programming software.
Technical specifications General Frequency range Working temperature Operating voltage Operate mode Dimensions Weight Antenna impedance Duty cycle Transmitter Frequency stability Output power Max frequency deviation Audio distortion Adjacent channel power Spurious radiation Occupied bandwidth Receiver RF sensibility Audio distortion Audio response Adjacent channel selectivity Intermodulation rejection Spurious response Blocking 446.00625- 446.09375 MHz (PMR446) -20°/+55° C 7.
Troubleshooting Problem Possible Cause The battery pack is discharged a installed correctly. The radio doesn’t switch on The radio switches off shortly after it has been switched on The battery pack does not recharge The radio switches on but is unable to receive signals Discharged battery pack. The battery-charger has not bee correctly.
and/or has not been Solution Verify that the battery pack is charged and that it has been correctly installed. Recharge the battery pack. en connected or installed Inspect the connections of the battery-charger and the installation of the batteries. elded. Move to an another area. Adjust the volume level. Check that the CTCSS tone or DCS code corresponds to the one set by the parties you are communicating with. Select the same radio channel used by the parties you been selected. are communicating with.
Prodotto o importato da: CTE INTERNATIONAL s.r.l. Via. R.Sevardi 7- 42124 Reggio Emilia Italia www.cte.it - www.midlandradio.eu L’uso di questo apparato può essere soggetto a restrizioni nazionali . Prima dell’uso leggere attentamente le istruzioni. Se il prodotto contiene batterie: non gettare nel fuoco, non disperdere nell’ambiente dopo l’uso, usare gli appositi contenitori per la raccolta. Produced or imported by: CTE INTERNATIONAL s.r.l. Via. R.
