User guide

RECHANNELIZE

TRANSPOSE

ToprogramtheF8torechannelizeanincomingMIDIchanneltoaselectedoutgoingMIDIchannelwhenafootswitch

isdepressed,senditthefollowingSystemExclusiveProgrammingcommand:

( , ,and areoptional)

AllbytesmustbeinHexadecimalformat(seehexadecimalconversiontableatend)

=FootswitchInput(00forFsw1...07forFsw8)

isoptional,ifincludedthenthe16notesfrommiddleCupareusedtoselectthechannel.Ifomitted,then

thenumberofnotesplayedwhilethefootswitchisdepressedisusedtoselectthechannel.

=IncomingMIDIchanneltorechannelize(seeMIDIchanneltableatend)

isoptional,specifiespresetoutgoingMIDIchannel(seeMIDIchanneltableatend)

isoptional,ifincludedthenincomingnotesareignoredwhilefootswitchisdepressed

TorechannelizeanincomingMIDIchanneldepressthefootswitch(theAll-Notes-Offmessageissentoutatthistime),

selectthechannelbyplayingnotesonthekeyboard(thesenotesarenotechoedtoMIDIOut),andreleasethe

footswitch.IfnonotesarereceivedbytheF8duringthisperiod,theoutgoingMIDIchannelissettothepreset .To

programtheF8toignoreincomingnotesandchangedirectlytothepresetMIDIchannel whenthefootswitchis

depressed,insert intheabovecommandasshown.

ToprogramtheF8toacceptrechannelizeselectionforincomingMIDIchannel1whenFsw1isdepressed,senditthe

followingSystemExclusiveprogrammingcommand:

F00000502409 F7

TorechannelizefromMIDIchannel1toMIDIchannel2depressFsw1,playanytwonotes,andreleasethe

footswitch.AllMIDIchannel1messageswillnowberechannelizedtoMIDIchannel2.Continuingtotapthe

footswitchwillcausetheF8totogglebetweentheoriginalandselectedchannels.

ToprogramtheF8totransposeincomingnotemessagesbyaselectedintervalbydepressingafootswitch,sendit

thefollowingSystemExclusiveProgrammingcommand:

( and areoptional)

AllbytesmustbeinHexadecimalformat(seehexadecimalconversiontableatend)

=FootswitchInput(00forFsw1...07forFsw8)

=IncomingMIDIchanneltotranspose(seeMIDIchanneltableatend)

isoptional,specifiespresettransposeinterval(40=zerotranspose)

isoptional,ifincludedthenincomingnotesareignoredwhilefootswitchisdepressed

Tospecifyatransposeintervaldepressthefootswitch(theAll-Notes-Offmessageissentoutatthistime),playthe

noteaboveorbelowmiddleCcorrespondingtothetransposeinterval(thisnoteisnotechoedtoMIDIOut),and

releasethefootswitch.IfnonotesarereceivedbytheF8duringthisperiod,thetransposeintervalissettothepreset

transposeinterval .ToprogramtheF8toignoreincomingnotesandchangedirectlytothepresettranspose

interval whenthefootswitchisdepressed,inserta afterthe intheaboveprogrammingcommand.

F00000502409ii(10)cc(pp)(00)F7 10pp 00

ExampleSetting

0000

ExampleOperationwithAboveSetting

F0000050240Aiicc(pp)(00)F7 pp 00

pp 00 pp