Instruction Manual

4
CLEARSETTINGS
DEVICEPARAMETERS
ToclearalloftheDualFootswitchController'ssettings,senditthefollowingSystemExclusivecommand:
ItisrecommendedtosendtheClearSettingscommandtotheDualFootswitchControllerpriortoprogrammingthe
unittoensurethatallprevioussettingsarecleared.
ThefollowingDeviceParametersareineffectregardlessofthefunctionsthateachofthefootswitchinputshavebeen
programmedtoperform.
WhenEchoisON,allincomingMIDImessagesreceivedbytheDualFootswitchControllerareechoedtoits
MIDIoutput.WhenEchoisOFF,onlythemessagesgeneratedbytheDualFootswitchControlleraresenttoitsMIDI
output.
TheDualFootswitchControllercanbeprogrammedtosendthestateofallfootswitch
inputsonpower-up.
WhentheToggleparameterisOFFforaparticularfootswitch,thefootswitchperformsthe
whenitis andthe whenitis WhenToggleisON,thefootswitchtoggles
betweenthe andthe eachtimethefootswitchisdepressed(nothingisdoneon
releaseofthefootswitch).
WhenAutoPolarityisONforafootswitch,theDualFootswitchControllerdeterminesthe
polarityofthefootswitchbasedonitspower-upstate.WhenAutoPolarityisOFF,thepolarityisforcedaccordingto
thePolaritysettings.
TheDualFootswitchControllercanwaituntilthebeginningofthenextbartoperformthe
footswitchaction.
TheDebounceTimespecifiesthelengthoftimeafterafootswitchchangesstatebeforeanew
changeofstateisallowedtooccur.
Toprogramtheseparameters,sendtheDualFootswitchControllerthefollowingSystemExclusiveprogramming
commands:
( isoptional)
=FootswitchInput(00forFsw1...01forFsw2)
=00:EchoOFF =01:EchoON
isoptional,If =01theDualFootswitchControllerwillsendthestateofeachfootswitchonpower-up.
( isoptional)
=FootswitchInput(00forFsw1...01forFsw2)
=00:ToggleOFF =01:ToggleON
=00:AutoPolarityOFF =01:AutoPolarityON
=00:NormallyOPENpolarity =01:NormallyCLOSEDpolarity( isignoredif =01)
isoptional.If =7F,waitforthebeginningofthenextbartoperformthefootswitchaction
( isoptional)
AllbytesmustbeinHexadecimalformat(seehexadecimalconversiontableatend)
=Debouncetimeinms
isoptional,ifincludedtheabovedebouncetime isdoubled
Theclearsettingscommandresetsthedebouncetimeto50ms
F0000050140000F7(allvaluesinHexadecimal)
Echo:
SendStateonPower-up:
Toggle:
FootswitchPolarity:
WaitforNextBar:
DebounceTime:
F0000050140001aa(bb)F7 bb
ii
aa aa
bb bb
F0000050140002iibbccdd(ee)F7 ee
ii
bb bb
cc cc
dd dd dd cc
ee ee
F0000050140003(00)ttF7 00
tt
00 tt
depressoperation
depressed, releaseoperation released.
depressoperation releaseoperation
PROGRAMMINGCOMMANDS