Refrigerator Freezer WHD-273FW1 / WHD-273FB1 / WHD-273FSS1
Contents 1. SAFETY WARNINGS ............................................................................................................ 1 2. INSTALLATION ..................................................................... Error! Bookmark not defined. 2.1 Location ...................................................................................................................... 2 2.2 Reversing the Door Swing .........................................................................................
1. SAFETY WARNINGS 1) WARNING―Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer. 2) WARNING―Do not damage the refrigerant circuit. 3) WARNING―Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer. 4) WARNING―DANGER: Risk of child entrapment.
2. INSTALLATION 2.1 Location When selecting a position for your unit you should make sure the floor is flat and firm, and the room is well ventilated. Avoid locating your unit near a heat source, e.g. cooker, boiler or radiator. Also avoid direct sunlight as it may increase the electrical consumption. Extreme cold ambient temperatures may also cause the unit not to perform properly. This unit is not designed for use in a garage or outdoor installation. Do not drape the unit with any covering.
2) Remove the screws fixed the top-hinge with cross-slot screwdriver. 3) Replace the top-hinge and the top-door limit block and the door bearing bush to the other side. A. Remove the nut with sleeve. Take off the washer then remove the axes to the other side and fixed. B. Remove the door limit block C. Please taking out another door limit block, with screw mounting to the door 4) Disassemble the screws fixed the bottom-hinge with cross-slot screwdriver.
Note：the refrigerator-freezer incline angle less 45°. 5) Replace the bottom door bearing bush and the limit block. 6) Replace the bottom hinge to the other side then fix it with screws. 7) Replace the mid-hinge.
8) Set the bottom door right position, fix the mid-hinge. 9) Replace the top-hinge. 10) Set the top door right position, fix the top-hinge and the cover. 11) Install the four screw caps and two catches to corresponding position.
12) Replace the leveler to the other side and adjust it to make sure the cabinet level. 2.3 Door Space Requirements The unit's door must be able to open fully as shown. D W×D≥35.5 X 41.4 inch W 2.4 Levelling the Unit To do this adjust the two levelling feet at the front of the unit. If the unit is not level, the door and magnetic seal alignments will not be covered properly. Make sure that the foot touches the ground before use.
Do not place items such as bottled or sealed container of fluid such as bottled beers and beverages in the freezer to prevent bursts and other losses. Before placing any food in your unit, turn it on and wait for 24 hours, to make sure it is working properly and to allow it time to fall to the correct temperature. Your unit should not be overfilled. ◆ Before Plugging in You must check that you have a socket which is compatible with the plug supplied with the unit.
3. PRODUCT OVERVIEW *All images in this instruction manual are for indication only; please refer to your individual unit for details. 4. OPERATION 4.1 Switching On Your Unit ◆The temperature selector knob is located on the right hand side wall of the refrigerator interior Setting“Off” ：Unit Off Setting“Min” ：Less Cool Temperature Setting“Med” ：Normal Operation(adequate for most situations) Setting“Max” ：Coolest Temperature ◆During high ambient temperatures e.g. on hot summer days.
4.2 Noise Inside the Unit! You may notice that your unit makes some unusual noises. Most of these are perfectly normal, but you should be aware of them! These noises are caused by the circulation of the refrigerant liquid in the cooling system. It has become more pronounced since the introduction of CFC free gases. This is not a fault and will not affect the performance of your unit. This is the compressor motor working, as it pumps the refrigerant around the system. 4.
6. MAINTENANCE 6.1 Changing the Internal Light Lamp replacement by professionals. 6.2 Care When Handling / Moving Your Unit Hold the unit around its sides or base when moving it. Under no circumstances should it be lifted by holding the edges of the top surface. 6.3 Servicing The unit should be serviced by an authorized engineer and only genuine spare parts should be used. Under no circumstances should you attempt to repair the unit yourself.
◆Buzz: Buzz will be generated by running compressor specially when starting up or shutting down. 8. TIPS FOR ENERGY SAVING Try not to open the door too often, especially when the weather is wet and hot. Once you open the door, close it as soon as possible. Every now and then check if the appliance is sufficiently ventilated (adequate air circulation behind the appliance). In normal temperature conditions, please arrange the thermostat at the middle setting.
