PORTABLE AIR CONDITIONER INSTRUCTION MANUAL Read Rules for Safe Operation and Instructions Carefully.
CONTENTS 1.SAFETY RULES............................................................................. 1 2.NAMES OF PARTS.......................................................................... 2 3.ACCESSORIES................................................................................ 2 4.OPERATION PANEL OF THE AIR CONDITIONER........................ 3 5.OPERATING INSTRUCTION FOR THE AIR CONDITIONER ........ 4 6.INSTALLATION...............................................................................
SAFETY RULES 1. DO NOT CONNECT UNIT TO ANY AC SOCKET IN DISREPAIR OR WITH CONNECTIONS. 2. DO NOT USE IN THE FOLLOWING LOCATIONS: - NEXT TO SOURCE OF FIRE. - AN AREA WHERE OIL IS LIKELY TO SPLASH. - AN AREA EXPOSED TO DIRECT SUNLIGHT. - AN AREA WHERE WATER IS LIKELY TO SPLASH. - NEAR A BATH, ASHOWER OR A SWIMMING POOL - IN THE GREEN HOUSE 3. NEVER INSERT YOUR FINGERS OR ANY FOREIGN OBJECTS INTO THE AIR OUTLET. TAKE SPECIAL CARE TO WARN CHILDREN OF THESE DANGERS. 4.
NAMES OF PARTS OPRATION PANEL REAR COVER AIR INLET FRONT COVER AIR OUTLET AIR OUTLET OUTDOOR WATER PUMP DRAIN HOSE AIR INLET OUTDOOR REMOTE CONTROLLER CASTER INDOOR CONTINUOUS DRAIN HOSE POWER CORD SIDE VIEW FRONT VIEW AIR INLET OUTDOOR REAR VIEW Fig.1 ACCESSORIES PARTS : PARTS NAME : QUANTITY : DUCT 1 ADAPTOR A (FOR PERMANENT DUCT 1 MOUNTING) ADAPTOR B (FOR TEMPORARY DUCT 1 MOUNTING) WALL PLUG 4 SCREWS 4 ALKALINE BATTERIES 2 REMOTE CONTROLLER 1 WATER PUMP DRAIN HOSE 1 Fig.
OPERATION PANEL OF THE AIR CONDITIONER(COOLING AND HEATING) DIGITAL DISPLAY FAN SPEED INDICATOR COOL/DRY/FAN/HEAT INDICATOR Green lamp will light when the mode is selected WATER FULL INDICATOR Red lamp will blink when the tank is full TEMP SETTING BUTTON Press your desired room temperature setting by pressing the button (up) or button (down) POWER INDICATOR INFRARED SIGNAL RECEIVER POWER BUTTON Turn on/off the unit MODES BUTTON Select the operation mode from COOL.DRY.FAN.
OPERATING INSTRUCTING FOR THE AIR CONDITIONER Before Starting This Unit 1) Select a suitable location, make sure you have easy access to an electrical outlet. 2) Install the Flexible Exhaust Hose and the Adjustable Window Slider Kit as depicted in Fig.5 & Fig.5a Fig.5a Fig.5 NOTE: Step 2 is required only while using the cooling mode . 3) Plug the unit into a 220-240V~50Hz/ or 220-230V~ 60Hz (Refer to the nameplate located on the right side of the unit.) grounded electrical outlet.
O O O O 2 COOLING OPERATION (Operating temperature range: 17 C-32 C/63 F-90 F) - Press the "MODE" button several times until the "COOL" indicator light comes on. - Press the "TEMP SETTING" buttons " " or " " to select your desired room temperature. (17OC-30OC/63OF-86OF) - Press the "FAN SPEED" button to choose the fan speed. O O O O 3 DEHUMIDIFYING OPERATION (Operating temperature range: 13 C-32 C/55 F-90 F) - Press the "MODE" button several times until the "DRY" indicator light comes on.
INSTALLATION 1 IMPORTANT: Install the mobile air conditioner in a flat and spacious location where the air outlets will not be covered up. A minimum clearance of 30cm from a wall or other obstacles should be kept. The appliance shall not be used in the laundry. The plug shall accessible after appliance is positioned. Wiring shall be done according to National rules. 30c m 30 cm Fig.7 2 DUCT MOUNT INSTRUCTIONS: Exhaust Air Oulet Duck Fig.8 A) TEMPORARY1.
Window Kit Installation Your window kit has been designed to fit most standard Vertical and horizontal window applications, However, it may be necessary for you to improvise/modify some aspects of the installation procedures for certain types of window. Please refer to Fig. 11 & Fig. 11a for minimum and maximum window openings.
TROUBLE SHOOTING TROUBLES POSSIBLE CAUSES SUGGEST REMEDIES 1. UNIT DOES NOT - Water full indicator blinks, water tank Dump the water in the water tank. START WHEN is full. PRESSING 1/0 BUTTON - Room temperature is higher than Reset the temperature. the set temperature.(Heating mode) - Room temperature is lower than Reset the temperature. the set temperature.(Cooling mode) 2. NOT COOL ENOUGH - The windows or doors in the room are not closed.
CS260-U
