en USER MANUAL EasyCool Portable MPF Rated voltage: 115V Frequency: 60Hz Before using this product, please read this manual carefully and keep it for future reference. The design and specifications are subject to change without prior notice for product improvement. Consult with your dealer or manufacturer for details. version A - 03 - 2018 MPF08CR81 MPF12CR81 MPF14CR81 www.midea.
Owner’s Manual 0 Safety Precautions ............................................................................ 3 1 Unit Specifications and Features ................................................... 5 2 Operating Instructions ..................................................................... 7 3 Installation Instructions ................................................................... 12 4 Care and Cleaning ............................................................................
Safety Precautions Safety Precautions To prevent injury to the user or personal or property damage, the following instructions must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The seriousness is classified by the following indications. This symbol indicates the possibility of death or serious injury. WARNING This symbol indicates the possibility of injury or damage to property.
Safety Precautions WARNING • The unit must be kept free from obstruction to ensure proper function. • DO NOT allow children to play with the air conditioner. Children must be supervised around the unit at all times. • If the air conditioner is knocked over during use, turn off the unit and unplug it from the main power supply immediately. Visually inspect the unit to ensure there is no damage. If you suspect the unit has been damaged, contact a technician or customer service for assistance.
Preparation Control panel Horizontal louver blade Caster Front Upper air filter (behind the grille) Handle (both sides) Upper air intake Drain outlet Air outlet Lower air filter Lower air intake Power plug socket Drain outlet (Heat pump mode only) Power cord outlet Power cord buckle Bottom tray drain outlet Rear Page 5 Unit Specifications and Features 1 Unit Specifications and Features
Design and Compliance Notes Unit Specifications and Features Design Notice: In order to ensure the optimal performance of our products, the design specifications of the unit and remote control are subject to change without prior notice. Energy Rating Information: The Energy Rating for this unit is based on an installation using an un-extended exhaust duct without adapters A or B (as shown in the Installation section of this manual).
2 Operating Instructions Key Pad Features Operating Instructions LED Display Swing Control Sleep Mode Auto Fan Mode Up (+) and Timer Speed Selector Down (-) Control Power Button Swing Button (optional) Timer button (Applicable to the models with auto swing feature only) Used to initiate the Auto swing feature. When the operation is ON, press the SWING button can stop the louver at the desired angle.
LED Display Operating Instructions Swing Control Sleep Mode Auto Fan Mode Up (+) and Timer Speed Selector Down (-) Control Power Button Mode button LED display Selects the appropriate operating mode. Each time you press the button, a mode is selected in a sequence that goes from AUTO, COOL, DRY, FAN and HEAT (only on heating models). The mode indicator light illuminates under the different mode settings. Shows the set temperature in °C or °F and the Auto-timer settings.
Operation Instructions TIMER operation • Press the “MODE” button until the “COOL” indicator light comes on. • Press the ADJUST buttons “+” or “-” to select your desired room temperature. The temperature can be set within a range of 17°C~30°C/62°F~86°F. • Press the “FAN SPEED” button to choose the fanspeed. • When the unit is on, pressing the Timer button will initiate the Auto-off stop program, the TIMER OFF indicator light illuminates. Press the UP or down button to select the desired time.
Other Features FOLLOW ME/TEMP SENSING Feature (optional) NOTE Operating Instructions This feature can be activated from the remote control ONLY. The remote control serves as a remote thermostat allowing for the precise temperature control at its location. To activate the Follow Me/Temp Sensing feature, point the remote control towards the unit and press the Follow Me/Temp Sensing button. The remote display is actual temperature at its location.
• During heat pump mode, remove the lower drain plug from the back of the unit, install the drain connector (5/8” universal female mender) with 3/4” hose (locally purchased). For the models without drain connector, just attach the drain hose to the hole. Place the open end of the Hose adaptor directly over the drain area in your basement floor. ¥ Remove the lower drain plug Continuous drain hose Delivery lift <1.8m Make sure the hose is secure so there are no leaks.
Installation Instructions 3 Choosing the Right Location Your installation location should meet the following requirements: • Make sure that you install your unit on an even and level surface to minimize noise and vibration. Installation Instructions • The unit must be installed near a grounded plug, and the Collection Tray Drain (found on the back of the unit) must be accessible. • The unit should be located at least 30 cm (12”) from the nearest wall to ensure proper air conditioning.
Tool Needed • Medium Phillips screwdriver; • Tape measure or ruler; • Knife or scissors; • Saw (optional, to shorten window adaptor for narrow windows). Accessories Your Window Installation Kit fits windows 67.5-123 cm (26.5-48”) and can be shortened for smaller windows.
Window Installation Kit Exhaust hose Exhaust hose assembly Step One: Preparing the exhaust hose assembly Press the exhaust hose into the window slider adaptor and unit adaptor, clamp automatically by elastic buckles of the adaptors.
NOTE Once the Exhaust Hose assembly and Adjustable Window Slider are prepared, choose from one of the following two installation methods. Foam seal B (Adhesive type-shorter) Type 1: Hung window installation 1. Cut the adhesive foam seal A and B strips to the proper lengths, and attach them to the window sash and frame as shown. Foam seal A (Adhesive type) Window slider A Window slider B (if required) Foam seal C (Non-adhesive type) Security Bracket 3.
Foam seal B (Adhesive type-shorter) Type 2: Sliding - casement window installation 1. Cut the adhesive foam seal A and B strips to the proper lengths, and attach them to the window sash and frame as shown. Foam seal A (Adhesive type) Window slider B (if required) 2. Insert the window slider assembly into the window opening. Window slider A Installation Instructions Foam seal C (Non-adhesive type) Security Bracket 3. Cut the non-adhesive foam seal C strip to match the window height.
4 Care and Cleaning Safety Precautions • Always unplug the unit before cleaning or servicing. • DO NOT use flammable liquids or chemicals to clean the unit. • DO NOT wash the unit under running water. Doing so causes electrical danger. • DO NOT operate the machine if the power supply was damaged during cleaning. A damaged power cord must be replaced with a new cord from the manufacturer.
5 Troubleshooting Tips Faults Diagnosis Please check the machine according to the following form before asking for maintenance: Problem Unit does not turn on when pressing ON/ OFF button Possible Cause Troubleshooting P1 Error Code. The water collection tray is full. Turn off the unit, drain the water from the water collection tray and restart the unit. In COOL mode: room temperature Reset the temperature. is lower than the set temperature.
6 Remote Control Operating Instructions Remote Control Specifications Model RG57H2(B)/BG(C)EF Rated voltage 3.0V (Dry batteries R03/LR03x2) Signal receiving range 8 m (26 ft) Environment -5°C ~ 60°C (23°F ~ 140°F) Function Buttons Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself.
Handing the Remote Control NOT SURE WHAT A FUNCTION DOES? Refer to the How to Use Basic Functions and How to Use Advanced Functions sections of this manual for a detailed description of how to use your air conditioner. SPECIAL NOTE Button designs on your unit may differ slightly from the example shown. If the unit does not have a particular function, pressing that function’s button on the remote control will have no effect.
Remote LED Screen Indicators Transmission Indicator Lights up when remote sends signal to unit MODE display Displays the current mode, including: ON/OFF display Appears when the unit is turned on and disappears when it is turned off AUTO COOL DRY HEAT FAN TIMER ON display Displays when TIMER ON is set TIMER OFF display Displays when TIMER OFF is set ECO display Not available in this unit Battery display Low battery detection SLEEP display Displays when SLEEP function is activated FOLLOW ME display Indic
How to Use Use the Basic Fuctions SETTING TEMPERATURE The operating temperature range for units is 17-30°C (62°F-86°F). You can increase or decrease the set temperature in 1°C (1°F) increments. AUTO operation 2 3 fav. 1 mode temperature In AUTO mode, the unit will automatically select the COOL, FAN, HEAT or DRY mode based on the set temperature. 1. Press the button to select Auto mode. fan 2. Set your desired temperature using the Temp Temp button. sleep swing follow me or LED 3.
FAN operation 1. Press the button to select FAN mode. button to select the fan speed: AUTO, 2. Press the LOW, MED or HIGH. 3 3. Press the fav. button to start the unit. 1 mode temperature 2 NOTE fan sleep swing follow me You can’t set temperature in FAN mode. As a result, your remote control’s LCD screen will not display temperature. LED HEAT operation 1. Press the button to select HEAT mode. 2. Set your desired temperature using the Temp Temp button. 2 4 fav.
Setting the Timer Functions 1 2 x5 Your air conditioning unit has two timer-related functions: TIMER ON - sets the amount of timer after which the unit will automatically turn on. - sets the amount of time after which the TIMER OFF unit will automatically turn off. TIMER ON function 3 1sec 4 2sec The TIMER ON function allows you to set a period of time after which the unit will automatically turn on, such as when you come home from work. button. By default, the last time period that 1.
3. Wait 2 seconds, then the TIMER OFF function will be activated. The digital display on your remote control will then return to the temperature display. T imer on NOTE Continue to press When setting the TIMER ON or TIMER OFF functions, up to 10 hours, the time will increase in 30 minute increments with each press. After 10 hours and up to 24, it will increase in 1 hour increments. The timer will revert to zero after 24 hours. fav. mode or temperature until desired time is reached.
How to Use the Advanced Fuctions SLEEP Function The sleep function is used to decrease energy use while you sleep (and do not need the same temperature settings to stay comfortable). This function can only be activated via remote control. Note: The sleep function is not available in FAN or DRY mode. fav. mode temperature fan sleep SWING Function swing follow me LED Used to stop or start louver movement and set the desired up/down air flow direction.
NOTES • The device could comply with the local national regulations. In Canada, it should comply with CAN ICES-3(B)/NMB-3(B). In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
