How to Guide

H
C
QUICK INSTALLATION GUIDE QUICK INSTALLATION GUIDE CONT.
This quick reference guide is provided for informational purposes only and does not replace,
modify or change in any manner the User Manual & Installation Instructions.
UNPACK YOUR WASHER
REMOVE SHIPPING HARDWARE
1
2
CONNECT HOSES TO
WATER SUPPLY
INSTALL DRAIN HOSE AND
CONNECT TO POWER SUPPLY
TEST CYCLE
4
6
8
IMPORTANT: Save all bolts and spacers for future use.
3
5
7
CONNECT HOSES TO WASHER
LEVEL YOUR WASHER
INSTALLATION CHECKLIST
1. Once the washer is within 4 feet of its fi nal
location, use an adjustable or   socket wrench
to remove the following from the back of the
washer:
• 4 shipping bolts
• 4 plastic spacers (including rubber grommets)
• 4 power cord retainers
2. Insert the hole caps into the bolt holes after the
shipping bolts and spacers have been removed.
1. Run water from both
faucets to fl ush the
lines and remove
particles that might
clog the water valve
screens.
2. Ensure that a rubber
washer is in the end
of the hot and cold
hoses.
3. Connect the inlet hoses
to the hot “H” outlet and
cold “C” outlet.
4. Hand-tighten, and then tighten the
connections another
 turn using pliers.
1. Rock the washer into fi nal
location, ensuring inlet
hoses do not become
kinked.
2. Place level on top of
washer.
3. Adjust the front leveling
legs up or down using a
 wrench.
4. Level washer both side-
to-side and front-to-back.
5. Turn lock nuts on leveling
legs up toward the base
of the washer, and then
tighten with the 
wrench.
Main power is turned on.
The washer is plugged in.
Water hoses are connected securely.
Faucets are turned on.
Washer is level and all legs are on the fl oor.
Shipping bolts and spacers are removed.
Drain hose is placed in tub or standpipe and secured
with a cable tie.
1. Ensure that a screen
washer is inserted
into the faucet end
of both hoses. If a
rubber washer is
already inserted,
remove before
inserting screen
washer.
2. Connect the inlet
hose from the “H”
outlet to the hot faucet
and the inlet hose from
the “C” outlet to the cold
faucet.
3. Hand-tighten, and then tighten the connections
another
 turn using pliers.
4. Turn on the water and check for leaks.
1. Attach U-shaped hose guide
to end of drain hose.
2. Place drain hose
in laundry tub or
standpipe and
secure with
cable tie.
NOTE: If placed in
a standpipe, the
end of the drain
hose should extend
only 4 to 7 inches
down the pipe.
3. Plug washer into a
grounded outlet. Do
not use an extension cord
or adapter plug.
1. Wash a load of clothes in the SPEED WASH cycle.
2. Check for leaks.
3. When the load is spinning at high speed, make sure the
washer and leveling legs are stable.
4. If necessary, adjust the front leveling legs while the
washer is in the spin cycle until the washer is level.
WARNING
For your safety
•
To reduce the risk of fi re, electric shock, or injury to persons when using or installing the product, read and obey all safety
information provided in the User Manual & Installation Instructions that accompanied the product.
•
Do not install or store appliance in an area where it will be exposed to dripping water or outside weather conditions. See
Location of Your Washer section in the User Manual & Installation Instructions.
•
NOTE: This appliance must be properly grounded and installed as described in these steps and the User Manual & Installation
Instructions. Electrical service to the washer must conform with local codes and ordinances and the latest edition of the
national Electrical Code, ANSI/NFPA 70.
Parts supplied
Cable Tie
Adjustable wrench
or
 socket with ratchet
Adjustable wrench or
 open-end wrench
Carpenter’s level
Channel-lock
adjustable pliers
Screen Washers (2)
hose guide
Tools needed
@Midea 2019