Midea Cooker Hood Instructions MODEL: MHC60SS MHC90SS SAVE THESE INSTRUCTIONS CAREFULLY Read the instructions carefully before using your cooker hood, and keep them carefully. If you follow the instructions, your cooker hood will serve you many years well.
RECOMMENDATIONS AND SUGGESTIONS The instructions apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your appliance. INSTALLATION ●● The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. ●● The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the cooker hood.
COMPONENTS Ref. Qty. Product Components 1 1 Hood Body, complete with Control, Light, Blower, Filter. 2.1 1 Lower Decorative Chimney 2.2 1 Upper Decorative Chimney 3 1 4 1 Exhaust Pipe 5 2 Activated Charcoal Filter (optional) Qty. Documentation 1 Instruction Manual Ref. Qty.
DIMENSION Option Chimney 1 400+0 2 400+300 4 A 689 689 B / 730-970
INSTALLATION WALL DRILLING AND BRACKET FIXING Option 1 2 Chimney 400+0 400+300 X / 390-620 As the first step, proceed with the following drawings: ●● A vertical line up to the ceiling or up to the upper limit, at the center of the area in which the hood is to be fitted. ●● A horizontal line A at 980 – 1080 mm above the cooker top. ●● A horizontal line B at X mm above the horizontal line A. ●● A horizontal line C at 261 mm below the horizontal line A (solution 2).
Hook the hood body ●● Hook the hood body to the bracket 20. ●● Level the hood body itself. ●● Lock screws (M5*12) into the hood fixing bracket to prevent the hood body from accidentally sliding off. ●● Remove the filter from the inside of the hood body, and fix the screw 10 to wall plug 11 at the point (3) (optional).
CHIMNEY ASSEMBLY The chimney can only be installed with an exhausting hood. Lower decorative chimney ●● Fix the lower decorative chimney to the hood body with 2 screws 12 (4.2 x 9.5) supplied with the hood. Upper Decorative Chimney ●● Slightly widen the two sides of the upper chimney and hook them between the wall and the bracket 21 which is fixed on the lower decorative chimney. ●● Fix the upper chimney onto the bracket 21 with 2 screws 12 (4.2 x 9.5) supplied with the hood.
USE Speed adjustment MOTOR OFF SWITCH: Press this switch to stop the motor. SPEED SWITCH: Press this switch, and the motor runs at LOW speed. SPEED SWITCH: Press this switch, and the motor runs at MEDIUM speed. SPEED SWITCH: Press this switch, and the motor runs at HIGH speed. LIGHT ON/OFF SWITCH: Press this switch to turn on the light, and press again to turn it off.
MAINTENANC GREASE FILTER METAL SELF-SUPPORTING GREASE FILTER CLEANING ●● The filters must be cleaned every 2 months of operation or more frequently for particularly heavy usage, and can be washed in a dishwasher. ●● Pull the comfort panel to open them. ●● Remove the filters one by one by pushing them towards the back side of the hood unit and simultaneously pulling downwards. ●● Any kind of bending of the filters has to be avoided when washing them.
●● Remove the grease filter, and carefully remove 2 screws from the front plate (a cross headed screwdriver will be needed to remove the screws). ●● Disconnect the terminal of LED light. ●● Press LED light at the back of the front plate, and take it out. ●● Replace the light (commercially available LED light (max. 1.5 w) Round/ Diameter: 70 mm Max Power Voltage 1.5 W DC 12 V Picture Light Cap ILCOS D Code —— DSR-1.
TROUBLE SHOOTING Fault Light is on, but motor does not work Cause Solution The blade is blocked. Check the blade. The capacitor is damaged. Replace the capacitor. The motor is damaged. Replace the motor. The internal wiring of motor is cut off/ disconnected. An unpleasant smell may Replace the motor. be produced. Apart from the above mentioned, check the following: Both light and motor do not work Oil leakage Vibration Light is damaged. Replace the light. Power cord is loose.
Maintenance schedule: To ensure the appliance continues to operate at peak performance, we recommend a routine service call every 3 years for the life of the appliance. FOR SPARE PARTS OR TO FIND THE ADDRESS OF YOUR NEAREST STATE SPARE PARTS CENTRE IN AUSTRALIA MIDEA HOME APPLIANCES AUSTRALIA PTY LTD 11/75 Lorimer Street, Docklands, Melbourne, 3008 After-sales service No.
