Midea Cooker Hood Instructions MODEL: MHC90CGSS SAVE THESE INSTRUCTIONS CAREFULLY Read the instructions carefully before using your cooker hood, and keep them carefully. If you follow the instructions, your cooker hood will serve you many years well.
RECOMMENDATIONS AND SUGGESTIONS The instructions apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your appliance. INSTALLATION ●● The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
COMPONENTS Ref. Qty. Product Components 1 1 Hood Body, complete with Control, Light, Blower, Filter. 2.1 1 Lower Decorative Chimney 2.2 1 Upper Decorative Chimney 4 1 Exhaust Pipe 5 2 Activated Charcoal Filter (optional) Ref. Qty. 10 7 Screws 5 x 50 11 7 Wall Plug 12 6 Screws 4.2 x 9.5 20 1 Hood Fixing Bracket (optional ) 21 2 Chimney Fixing Bracket (0 / 1 optional) Installation Components Qty.
DIMENSION A B C D E 4 900 276 485 485-865 323
INSTALLATION WALL DRILLING AND BRACKET FIXING As the first step, proceed with the following drawings: ●● A vertical line up to the ceiling or up to the upper limit, at the center of the area in which the hood is to be fitted. ●● A horizontal line A at 1320 – 1700 mm above the cooker top. ●● A horizontal line B at minimum 926 mm above the cooker top. ●● A horizontal line C at minimum 730 (910 optional) mm above the cooker top.
●● Mark a point (3) on the horizontal line C, 130 (250 optional) mm to the vertical reference line. ●● Repeat this operation on the other side, checking that the two marks are on one horizontal line. Fix the brackets (optional): ●● ●● ●● ●● Drill holes at the marked points with a ɸ10 mm drill bit. Insert the wall plugs 11 into the holes. Fix the hood fixing bracket 20 with 3 screws 10 (5 x 50) at the horizontal line A, Fix the chimney fixing bracket 21 with 2 screws 10 (5 x 50) at the horizontal line B.
CHIMNEY ASSEMBLY The chimney can only be installed with an exhausting hood. Lower decorative chimney ●● Fix the lower decorative chimney to the hood body with 2 screws 12 (4.2 x 9.5) supplied with the hood. Upper Decorative Chimney ●● Slightly widen the two sides of the upper chimney and hook them between the wall and the bracket 21 which is fixed on the lower decorative chimney. ●● Fix the upper chimney onto the bracket 21 with 2 screws 12 (4.2 x 9.5) supplied with the hood.
USE Speed adjustment MOTOR OFF SWITCH: Press this switch to stop the motor. SPEED SWITCH: Press this switch, and the motor runs at LOW speed. SPEED SWITCH: Press this switch, and the motor runs at MEDIUM speed. SPEED SWITCH: Press this switch, and the motor runs at HIGH speed. LIGHT ON/OFF SWITCH: Press this switch to turn on the light, and press again to turn it off.
MAINTENANC GREASE FILTER METAL SELF-SUPPORTING GREASE FILTER CLEANING ●● The filters must be cleaned every 2 months of operation or more frequently for particularly heavy usage, and can be washed in a dishwasher. ●● Pull the comfort panel to open them. ●● Remove the filters one by one by pushing them towards the back side of the hood unit and simultaneously pulling downwards. ●● Any kind of bending of the filters has to be avoided when washing them.
LIGHTING LIGHT REPLACEMENT LIGHTING LIGHTING LIGHT REPLACEMENT Replacing the light modules LIGHT REPLACEMENT Replacing You cannot the light bulbs, the entire light module has to be replaced. thereplaced light modules Replacing light module Whenthe changing the light modules, the contacts are live. YBefore ou cannot the light light bulbs, the entire light module has to bemains replaced. ●● You should notreplaced replace bulb but the entire light module.
TROUBLE SHOOTING Fault Cause Solution The blade is blocked. Light is on, but motor does not work The capacitor is damaged. Replace the capacitor. The motor is damaged. Replace the motor. The internal wiring of motor is cut off/ disconnected. An unpleasant smell may Replace the motor. be produced. Apart from the above mentioned, check the following: Both light and motor do not work Oil leakage Vibration Light is damaged. Replace the light. Power cord is loose.
Maintenance schedule: To ensure the appliance continues to operate at peak performance, we recommend a routine service call every 3 years for the life of the appliance. FOR SPARE PARTS OR TO FIND THE ADDRESS OF YOUR NEAREST STATE SPARE PARTS CENTRE IN AUSTRALIA MIDEA HOME APPLIANCES AUSTRALIA PTY LTD 11/75 Lorimer Street, Docklands, Melbourne, 3008 After-sales service No.
