WIRED REMOTE CONTROLLER Installation and Owner’s Manual MODEL: KJR-120G1/TFBG-E(5V)（For high wall models） KJR-120G2/TFBG-E(12V) (For Duct/Cassette/Floor ceiling models) IMPORTANT NOTE: Read this manual carefully before installing or operating your wired remote controller. Make sure to save this manual for future reference.
● This manual gives detailed description of the precautions that should be brought to your attention during operation. ● To ensure the correct service of the wired controller, read this manual carefully before using the unit. ● Keep this manual after reading for future reference.
CONTENTS 1. SAFETY PRECAUTION....................................................................... 1 2. INSTALLATION ACCESSORY.............................................................. 2 3. INSTALLATION METHOD....................................................................4 4. APPENDIX INSTALL THE WIRE CONTROLLER KIT...............................10 5. SPECIFICATION...............................................................................16 6. WIRED CONTROLLER FEATURES AND FUNCTIONS..........
1. SAFETY PRECAUTION Read the safety precautions carefully before installing the unit. Stated below are important safety issues that must be obeyed. WARNING Means improper handling may lead to personal death or severe injury. CAUTION Means improper handling may lead to personal injury or property loss. WARNING Please entrust the distributor or professionals to install the unit. Installation by other persons may lead to imperfect installation, electric shock or fire.
2. INSTALLATION ACCESSORY Select the installation location Don’t install at the place where cover with heavy oil, vapor or sulfureted gas, otherwise, this product would be deformed that would lead to system malfunction. Preparation before installation 1. Please confirm that all the following parts you have been supply. No. Qty.
2. INSTALLATION ACCESSORY WIRED CONTROLLER INSTALLATION PRECAUTION 1. This manual provides the wired controller installation method. Refer to the wiring diagram in this installation manual to wire the wired controller with the indoor unit. 2. The wired controller works in a low voltage loop circuit. Do not connect directly to 208/230V and 460V. Do not wire this kind of wire into a loop. Wiring clearance between the configured tubes should range 11.81−19.69 inches (30−50 cm) or above. 3.
3. INSTALLATION METHOD 1.Wired Remote Controller Dimensions 120mm (4.7”) 18.5mm (0.7”) 46mm (1.8”) 83.5mm (3.3”) 123mm (4.8”) 62mm (2.4”) Fig 3-1 2.
3. INSTALLATION METHOD 3.Wiring figure Mainboard 4-core shielding wire The connection cable CN40 Model A:KJR-120G2/TFBG-E(12V) Fig 3-3(A) Connect the female joint of the wires group from the mainboard with the male joint of the connective wires group. (See Fig.3-3(A)) Connect the other side of the connective wires group with the male joint of the wires group leads from the wire controller.(See Fig.
3. INSTALLATION METHOD Install the Adapter Board and the Display Board on the High Wall (See the Appendix for instructions). Connect the female joint of the wires group from the adapter board with the male joint of theconnective wires group. Next, connect the other side of the adapter board with the displayboard. (See Fig.3-3(B)) Connect the other side of the connective wires group with the male joint of the wires group leads from the wire controller. (See Fig.3-3(B)) 4.
3. INSTALLATION METHOD For switch box mounting, fasten the back plate on the switch box with 2 screws (M4x25) and fasten it on the wall with 1 screw (M4x20). (Fig.3-6) Back plate Switch box Screw (M4×20) Screws (M4×25) Fig 3-6 NOTE: Place on a flat surface. Be careful not to distort the wire controller’s back plate by over−tightening the mounting screws. 6. Battery installation Fig 3-7 Place the battery in the unit and ensure the positive side of the battery is in accordance with the polarity markings.
3. INSTALLATION METHOD 7. Wire the indoor unit There are three methods: 1 from the rear; 2 from the bottom; 3 from the top; 1 1 3 PCB PCB 1 2 PCB 4. Notch the part for the wiring to pass through with a nipper tool.
3. INSTALLATION METHOD NOTE: DO NOT allow water to enter the remote control. Use the trap and putty to seal the wires. Putty Trap Putty Putty Trap Trap Fig 3-8 8. Reattach the wire controller’s upper part While adjusting and mounting the upper case, avoid clamping the wiring during installation. (Fig 3-9) Fig 3-9 IMPORTANT: All the pictures in this manual are for illustration purposes only. Your wire controller may differ slightly.
4. APPENDIX INSTALL THE WIRE CONTROLLER KIT 1. Open the front panel. 2. Disconnect the wire from the main controller board.
4. APPENDIX INSTALL THE WIRE CONTROLLER KIT 3. Identify the components. From left to right, the wired controller, convert board and the display board. 4. Identify connections on the Display Board. CN201 is the display board connection to the main board wire (on the display board).
4. APPENDIX INSTALL THE WIRE CONTROLLER KIT CN101 is the display board connection to the convert board wire (on the display board). 5. Uninstall the display board from the front panel. Keep the display board holder.
4. APPENDIX INSTALL THE WIRE CONTROLLER KIT 6. Carefully bend and break off the rectangular section (upper left section with two diagonal holes) from the display board. NOTE: Break off the upper left hand rectangle (section with the two holes marked with a red rectangle). 7. Replace the old display board (for the New Display board provided) and secure with the clips. To uninstall the clips, push the clips inward.
4. APPENDIX INSTALL THE WIRE CONTROLLER KIT 8. Before assembling mounting back on the Front Panel, remove the display board’s screen cover. 9. Connect the Wires to the Adaptor Board. a. Connect the wire coming from the Display board to the Convert Board (this connection consists of 5 wires).
4. APPENDIX INSTALL THE WIRE CONTROLLER KIT b. Connect the wire coming from the Wired Remote Controller to the Convert Board (this connection consists of 4 wires). 10. Once the ports are connected, install the cover. 11. Mount the new display board and convert board to the Front Panel. 12. Connect the wired remote controller to the display board and the convert board. 13. Connect the wire from the main controller board (see Fig 3-2).
5. SPECIFICATION Input voltage DC 5V/DC 12V Ambient temperature 23~110℉(-5~43℃) Ambient humidity RH40%~RH90% Wiring specifications Wiring type Shielded vinyl cord or cable 16 Size 0.029 in-0.74mm (0.75-1.
6. FEATURE AND FUNCTION OF THE WIRED CONTROLLER Feature: Swing Timer Day off/Del Confirm Back/Turbo ℃ Copy/ Follow me ℉ Mode - LCD display. Malfunction code display: displays the error code (helpful for servicing) 4-way wire layout design. Room temperature display.
7. WIRED CONTROLLER DISPLAY 1 2 3 4 5 6 7 8 9 10 11 12 13 15 1. Operation mode indicator 2. Fan speed indicator 3. Left-right swing indicator 4. Up-down swing indicator 5. Faceplate function indicator 6. Main unit and secondary unit indicator 7. Follow me function indicator 18 14 8. Turbo/Auxiliary Heat function indicator 9. °C / °F indicator 10. Temperature display 11. Lock indicator 12. Room temperature indicator 13. Clock display 14. On/Off timer 15.
8. WIRED CONTROLLER BUTTONS 5 6 7 Swing Timer Day off/Del Confirm Back/Turbo Copy/ Follow me Mode 8 9 10 1 2 3 - + Fan speed 3 4 (Lock) 1. Mode 2. Power 3. Adjust 4. Fan Speed 5. Swing 6. Timer 7. Day Off/Del 8. Copy/Follow me 9. Back/Turbo 10.
9. PREPARATORY OPERATION Set the current day and time 1 Press TIMER for 3s or more. The timer displays flashes. Timer Press + or − to set the date. The selected date flashes. 2 3 - + Date setting is complete and the time setting is ready after pressing TIMER or if nothing is pressed in 10 seconds. Timer 4 - + Press + or − to set the current time. Press repeatedly to adjust the current time in 1 minute increments. Press and hold to adjust the current time. ex.
10. OPERATION To start/stop operation Press the Power button. To set the operation mode Operation mode setting Press MODE to set the operation mode. (Heat function is invalid for cool only type unit) Mode Room temperature setting - + Press + or − to set the room temperature. Indoor Setting Temperature Range: 62~86℉(17~30℃)/62~88℉(17~31℃(depending on models)).
10. OPERATION Fan speed setting Press FAN SPEED to set the fan speed NOTE: This function is unavailable in the AUTO or DRY modes. Fan speed (Lock) Room temperature sensor selection Press FOLLOW ME to select whether the room temperature is detected at the indoor unit or at the wired controller. Copy/ Follow me Indoor Unit NOTE: When the FOLLOW ME function indication appears, the room temperature is detected at the wire remote controller.
10. OPERATION Child lock function Press LOCK for 3 seconds to activate the CHILD LOCK feature and lock all buttons on the wired controller. Press again for 3 seconds to deactivate. Fan speed (Lock) NOTE: When the child lock function is activated, the lock image appears. keypad tone setting Timer Swing Press SWING and TIMER simultaneously for 3 seconds to disable the keypad tone. Press the buttons again for 3 seconds to enable the keypad tone.
10. OPERATION Turbo/Auxiliary Heat function (on some models) • Press TURBO to activate/deactivate the Turbo/Auxiliary Back/Turbo Heat function. The turbo function sets the unit to reach the user’s present temperature in the shortest amount of time possible. • When the user presses TURBO in the COOL mode, the unit sets to the highest fan speed setting to jump−start the cooling process. • When the user presses TURBO in the HEAT mode, for units with AUX. HEAT, the AUX.
10. OPERATION Swing function (For the unit with left & right auto swing function only) 1 Up-Down swing Swing Press the Swing button to start up-down swing function. Press it again to stop. When the Up-Down swing function is activated,the mark appears. 2 Left-Right swing Swing Press the Swing button long to start Left-Right swing function. Press it again to stop. When the Left-Right swing function is activated, the mark appears.
10. OPERATION Swing function (For the unit without left & right auto swing function models) Up-Down airflow direction and swing Swing Use SWING to adjust the up and down airflow direction. 1.Every time the user presses SWING, the louver swings six degrees. 2.Press and hold SWING for 2 seconds, it changes to the UP−DOWN SWING mode. Press SWING again to stop. When the Up-Down swing function is activated,the mark appears.
11. TIMER FUNCTIONS WEEKLY timer Use to set the operating times for each day of the week. On timer Use to start the air conditioner operation. The timer operates and the air conditioner operation starts after the time has passed. Off timer Use to stop the air conditioner operation. The timer operates and the air conditioner operation stops after the time has passed. On and Off timer Use to start and stop the air conditioner operation.
11. TIMER FUNCTIONS To set the On or Off TIMER 1 Press Timer to select the Timer or . No display 2 Press Confirm and the Clock display flashes Confirm 3 - + ex.Off timer set at PM 6:00 Press + or − to set the time. After the time is set, the timer starts or stops automatically. 4 28 Confirm Press Confirm again to finish the settings.
11. TIMER FUNCTIONS To set the On and Off TIMER 1 Timer 2 Confirm Press Timer to select the . Press Confirm and the Clock display flashes. 3 Confirm - + Press the button + or - to set the On timer and then press Confirm. 4 - 5 Confirm + Press + or - to set the Off timer. Press Confirm to finish the setting.
12. WEEKLY TIMER 1 Weekly timer setting Confirm Timer Press Timer to select the and press Confirm. 2 Day of the week setting Confirm - + Press + or − to select the day of the week and then press CONFIRM. 3 ON timer setting of timer setting 1 Confirm - 30 + Press + and − to select the setting time. The setting time, mode, temperature and fan speed appear on the LCD. Press CONFIRM to enter the setting time process.
12. WEEKLY TIMER IMPORTANT: Up to 8 scheduled events can be set on one day. Various events can be scheduled in either MODE, TEMPERATURE and FAN speeds. 4 Time setting Confirm - + ex.Tuesday time scale 1 Press + and − to set the time then press CONFIRM. 5 Operation mode setting Confirm - + Press + and − to set the operation mode then press CONFIRM. 6 Room temperature setting Confirm - + Press + and − to set the room temperature then press CONFIRM.
12. WEEKLY TIMER 7 Fan speed setting Confirm - + Press + and − to set the fan speed then press CONFIRM. NOTE: This setting is unavailable in the AUTO, DRY or OFF modes. 8 Different scheduled events can be set by repeating steps 3 through 7. 9 Additional days, in a one week period, can be set by repeating steps 3 through 8. NOTE: The weekly timer setting can be returned to the previous step by pressing BACK. The current setting is restored.
12. WEEKLY TIMER WEEKLY timer operation To start Press Timer to select the starts automatically. Timer , and then the timer ex. To cancel Press Power to cancel the timer mode. The timer mode can also be canceled by changing the timer mode using Timer. Timer To set the DAY OFF (for a holiday) 1 2 After setting the weekly timer, press CONFIRM. Confirm - + Press + or − to select the day of the week.
12. WEEKLY TIMER 3 Press DAY OFF to create an off day. Day off/Del The mark is hidden ex.The DAY OFF is set for Wednesday 4 5 Set the DAY OFF for other days by repeating the steps 2 and 3. Back/Turbo Press BACK to revert to the weekly timer. ● To cancel, follow the same procedures used for setup. ● NOTE: The DAY OFF setting is cancelled automatically after the set day has passed. Copy out the setting in one day into the other day.
12. WEEKLY TIMER 3 4 5 The Copy/ Follow me Press COPY, the letters CY appear on the LCD. Press + or − to select the day to copy to. - + Copy/ Follow me Press COPY to confirm. mark flashes quickly ex. Copy the setting of Monday to Wednesday 6 Other days can be copied by repeating steps 4 and 5. 7 Confirm Press CONFIRM to confirm the settings. 8 Back/Turbo Press BACK to revert to the weekly timer.
12. WEEKLY TIMER Delete the time scale in one day. 1 During the weekly timer setting, press CONFIRM. Confirm 2 Confirm - + 3 Press + and − to select the day of the week and then press CONFIRM. Day off/Del - + Press + and − to select the setting time want to delete. The setting time, mode, temperature and fan speed appear on the LCD. The setting time, mode, temperature and fan speed can be deleted by pressing the DEL (day off). ex.
13. FAULT ALARM HANDING If the system does not properly operate except in the aforementioned cases or the aforementioned malfunctions are evident, investigate the system according to the following procedures. NO. MALFUNCTION AND PROTECTION DEFINITION DISPLAY DIGITAL TUBE 1 Communication error between wired controller and indoor unit F0 2 The faceplate is abnormal F1 Please check the indoor unit’s error display and review the owner’s manual if other error codes appear. 14.
QSXUI-009AEN The design and specifications are subject to change without prior notice for product improvement.Consult with the sales agency or manufacturer for details.
