User Manual
Table Of Contents
- About This Manual
- Copyright
- Proprietary Material
- Quality Certification
- Regulatory Status
- Conventions
- Symbols Used
- Warranty Information
- Introduction
- Product Description
- Routine Operation
- 3.1 Chapter Overview
- 3.2 Overview of Controls, Indicators, and Connectors
- 3.3 Preparing for Operation
- 3.4 Using the STRATA TX Screens
- 3.5 TXU and/or TCU Monitoring Operations
- 3.5.1 Using the Monitor Screens in MPEG Output Mode
- 3.5.2 Using the Monitor Screens in Ext IF Input Mode
- 3.5.3 Using the Monitor Screens in COFDM - IF Mode
- 3.5.4 Using the Monitor Screens in COFDM ASI In Mode
- 3.5.5 Using the Monitor Screens in Analog - IF Mode
- 3.5.6 Using the Monitor Screens in DVB-S Mode
- 3.6 TXU and/or TCU Control Operations
- 3.7 Front Panel vs. STRATA TX Configurator Settings
- Table 3-1: Front Panel vs. Configurator Settings
- Troubleshooting
- Channels & Frequencies
- A.1 Appendix Overview
- A.2 Initial Factory Presets
- A.2.1 3.4 to 3.8 GHz Channel Plan
- A.2.2 4.4 to 5.0 GHz Channel Plan
- A.2.3 6.4 to 7.1 GHz Channel Plan
- A.2.4 6.9 to 7.5 GHz Channel Plan
- A.2.5 7.4 to 8.0 GHz Channel Plan
- A.2.6 7.8 to 8.5 GHz Channel Plan
- A.2.7 8.2 to 8.9 GHz Channel Plan
- A.2.8 10.0 to 10.7 GHz Channel Plan
- A.2.9 10.5 to 11.2 GHz Channel Plan
- A.2.10 10.8 to 11.5 GHz Channel Plan
- A.2.11 12.7 to 13.25 GHz Channel Plan
- Glossary
- Specifications
Routine Operation 3-35STRATA TX Operator’s Guide/Tech Ref Manual
3.7 Front Panel vs. STRATA TX
Configurator Settings
The design of the STRATA TX System and STRATA TX
Configuration Utility software makes commonly available
settings accessible from the TXU and/or TCU front panel and
more advanced settings accessible through the STRATA TX
Configuration Utility.
A summary of settings that can be controlled by each method is
shown in Table 3-1.
Table 3-1: Front Panel vs. Configurator Settings
Parameter
Available
Settings
Set
Using
Control
Switch
Set Using TX
Configurator
Presets
Preset in use 1, 2,... 9
✔ ✔
Preset text Any 12
alphanumeric
characters
✔
Operation Mode • MPEG IF Out
✔
• MPEG ASI
Out
✔
• COFDM-ASI
In
✔
• Ext IF In
✔
• Analog IF Out
✔
• DVB-Satellite
✔
Color Bars • PAL ✔
•NTSC
✔
•OFF
✔
•Auto
✔
IF CW Tone • ON
✔
•OFF
✔
Channels
Channel &
Offset in use
• 1 thru 10
✔
• -, Center, +
✔
Channel &
Offset
frequencies
Depends on band
✔
DC Power
DC On Coax (75
Ohm Coax)
• Power Off
✔
• Power On
✔
COFDM
COFDM
Bandwidth
•6 MHz
✔
•7 MHz
✔
•8 MHz
✔
COFDM
Modulation
(MPEG IF Out
and COFDM-
ASI In Modes)
• QSPK
✔
• 16 QAM
✔
• 64 QAM
✔
Table 3-1: Front Panel vs. Configurator Settings (Continued)
Parameter
Available
Settings
Set
Using
Control
Switch
Set Using TX
Configurator