User Manual
Table Of Contents
- About This Manual
- Copyright
- Proprietary Material
- Quality Certification
- Regulatory Status
- Conventions
- Symbols Used
- Warranty Information
- Introduction
- Product Description
- Routine Operation
- 3.1 Chapter Overview
- 3.2 Overview of Controls, Indicators, and Connectors
- 3.3 Preparing for Operation
- 3.4 Using the STRATA TX Screens
- 3.5 TXU and/or TCU Monitoring Operations
- 3.5.1 Using the Monitor Screens in MPEG Output Mode
- 3.5.2 Using the Monitor Screens in Ext IF Input Mode
- 3.5.3 Using the Monitor Screens in COFDM - IF Mode
- 3.5.4 Using the Monitor Screens in COFDM ASI In Mode
- 3.5.5 Using the Monitor Screens in Analog - IF Mode
- 3.5.6 Using the Monitor Screens in DVB-S Mode
- 3.6 TXU and/or TCU Control Operations
- 3.7 Front Panel vs. STRATA TX Configurator Settings
- Table 3-1: Front Panel vs. Configurator Settings
- Troubleshooting
- Channels & Frequencies
- A.1 Appendix Overview
- A.2 Initial Factory Presets
- A.2.1 3.4 to 3.8 GHz Channel Plan
- A.2.2 4.4 to 5.0 GHz Channel Plan
- A.2.3 6.4 to 7.1 GHz Channel Plan
- A.2.4 6.9 to 7.5 GHz Channel Plan
- A.2.5 7.4 to 8.0 GHz Channel Plan
- A.2.6 7.8 to 8.5 GHz Channel Plan
- A.2.7 8.2 to 8.9 GHz Channel Plan
- A.2.8 10.0 to 10.7 GHz Channel Plan
- A.2.9 10.5 to 11.2 GHz Channel Plan
- A.2.10 10.8 to 11.5 GHz Channel Plan
- A.2.11 12.7 to 13.25 GHz Channel Plan
- Glossary
- Specifications
Routine Operation 3-31STRATA TX Operator’s Guide/Tech Ref Manual
Figure 3-27: Main Screen (Typical) - Preset Changed
10. Press the control switch for one second to place the
TX System in the transmit mode, as required.
3.6.2 Setting a Channel
The STRATA TX channel and offset, other than the Preset
channel pre-programmed using the STRATA TX Configuration
Utility software, can be selected from the TXU or TCU front panel
and can be configured for operation on any of up to 10 channels,
with (+) and (-) offsets. For more information, see the “Channels
& Frequencies” Appendix on page A-1.
The frequencies assigned to each channel must be configured
using the STRATA TX Configuration Utility software. The
frequencies cannot be changed from either the TXU or TCU front
panels.
For information on configuring channels, see the “Configurator
Reference” Appendix on page C-1 (part of the STRATA TX
System Technical Reference Manual only).
Preset
. W
New
Preset
Notes
The Preset will retain the new channel until the TX
System is powered off. When the TX System is
powered up again, the new channel setting will be
retained.
When a Preset is changed, the channel does not
change.
When a channel is changed, the Preset does not
change.
To select which channel to modify, perform the following steps:
1. Verify the STRATA TX System is connected and
powered up. See ”Powering the STRATA TX System”
on page 3-12.
2. Observe the Main screen is displayed. See Figure 3-
28.
Figure 3-28: Main Screen
3. Turn the control switch ccw until the display reads Set
Channel. See Figure 3-29.
Figure 3-29: Change a Channel (Typical)
Preset 3
. W
Set Channel
Not On Chnl