User Manual
Table Of Contents
- About This Manual
- Copyright
- Proprietary Material
- Quality Certification
- Regulatory Status
- Conventions
- Symbols Used
- Warranty Information
- Introduction
- Product Description
- Routine Operation
- 3.1 Chapter Overview
- 3.2 Overview of Controls, Indicators, and Connectors
- 3.3 Preparing for Operation
- 3.4 Using the STRATA TX Screens
- 3.5 TXU and/or TCU Monitoring Operations
- 3.5.1 Using the Monitor Screens in MPEG Output Mode
- 3.5.2 Using the Monitor Screens in Ext IF Input Mode
- 3.5.3 Using the Monitor Screens in COFDM - IF Mode
- 3.5.4 Using the Monitor Screens in COFDM ASI In Mode
- 3.5.5 Using the Monitor Screens in Analog - IF Mode
- 3.5.6 Using the Monitor Screens in DVB-S Mode
- 3.6 TXU and/or TCU Control Operations
- 3.7 Front Panel vs. STRATA TX Configurator Settings
- Table 3-1: Front Panel vs. Configurator Settings
- Troubleshooting
- Channels & Frequencies
- A.1 Appendix Overview
- A.2 Initial Factory Presets
- A.2.1 3.4 to 3.8 GHz Channel Plan
- A.2.2 4.4 to 5.0 GHz Channel Plan
- A.2.3 6.4 to 7.1 GHz Channel Plan
- A.2.4 6.9 to 7.5 GHz Channel Plan
- A.2.5 7.4 to 8.0 GHz Channel Plan
- A.2.6 7.8 to 8.5 GHz Channel Plan
- A.2.7 8.2 to 8.9 GHz Channel Plan
- A.2.8 10.0 to 10.7 GHz Channel Plan
- A.2.9 10.5 to 11.2 GHz Channel Plan
- A.2.10 10.8 to 11.5 GHz Channel Plan
- A.2.11 12.7 to 13.25 GHz Channel Plan
- Glossary
- Specifications
Routine Operation 3-30STRATA TX Operator’s Guide/Tech Ref Manual
3.6.1 Changing a Preset
The STRATA TX is designed to enable you to control operating
settings through Presets stored in the transmitter. The STRATA
TCU and TXU are shipped with factory Presets and can be
customized for the user.
Your STRATA TX System can be pre-configured with up to 9
Presets. Each Preset contains most of the operating settings
needed to control the STRATA TX System. System Presets can
only be defined and changed using the STRATA TX
Configuration Utility software. Presets cannot be changed from
the TXU or TCU front panels.
For information on configuring Presets, see the “Configurator
Reference” Appendix on page C-1 (part of the STRATA TX
Technical Reference Manual only).
Notes
When you change a Preset, the new Preset
remains in effect. When the TX System is powered
down, that Preset is active when the TX System is
powered up again.
When a Preset is changed, the channel does not
change.
When a channel is changed, the Preset does not
change.
To change Presets, perform the following steps:
1. Verify the STRATA TX System is connected and
powered up. See ”Powering the STRATA TX System”
on page 3-12.
2. Observe the Main Screen is displayed. See Figure 3-
25.
Figure 3-25: Main Screen - Changing a Preset
3. Turn the control switch ccw until the display reads
Chng Preset.
Note
Changing Presets when the TX System is in the
transmit mode will place the transmitter in the
standby mode when the control switch is pressed.
4. Press the control switch to select Chng Preset. See
Figure 3-26.
Figure 3-26: Change Preset Screen (Typical)
5. Observe the current Preset setting begins to blink.
6. Turn the control switch cw or ccw until the desired
Preset is displayed.
7. Press the control switch once to select that Preset.
8. Observe display changes back to the Main Screen
after a short delay.
9. Observe newly selected Preset is displayed on Main
screen. See Figure 3-27 on page 3-31.
Preset 3
. W
Chng Preset
Preset 1
Blinking