User Manual
Table Of Contents
- Notices
- Contents
- Introduction
- Product Description
- Routine Operation
- 3.1 Chapter Overview
- 3.2 Overview of Controls, Indicators and Connectors
- 3.3 Preparing for Operation
- 3.4 Using the Display Screens
- 3.5 PTX-PRO Monitoring Operations
- 3.6 PTX-PRO Control Operations
- 3.7 Front Panel vs. Configurator Settings
- Troubleshooting
- Advanced Operation
- 5.1 Chapter Overview
- 5.2 Before You Begin
- 5.3 Create or Update a Configuration
- 5.3.1 Using the Configurator Software
- 5.3.2 Determine Licensed Options
- 5.3.3 Create New Configuration On-Line
- 5.3.4 Load and Modify Configuration Settings On- Line
- Figure 5-7: Load and Modify Configuration Settings On-Line - Sheet 1 of 5
- Figure 5-8: Load and Modify Configuration Settings On-Line - Sheet 2 of 5
- Figure 5-9: Load and Modify Configuration Settings On-Line - Sheet 3 of 5
- Figure 5-10: Load and Modify Configuration Settings On-Line - Sheet 4 of 5
- Figure 5-11: Load and Modify Configuration Settings On-Line - Sheet 5 of 5
- 5.3.5 Load Configuration File into Radio On-Line
- 5.3.6 Change Preset Names in On-Line Mode
- 5.3.7 Create Channel Plan Offline
- 5.3.8 Modify Channel Plan in Offline Mode
- 5.3.9 Load and Modify a Channel Plan On-Line
- 5.3.10 Load Channel Plan File into Radio On-Line
- 5.3.11 Add Licensed Option
- Installation
- 6.1 Chapter Overview
- 6.2 Unpacking
- 6.3 Initial Inspection
- 6.4 Damage in Shipment
- 6.5 Mounting and Cabling
- 6.6 Power Connections
- 6.7 Grounding
- 6.8 Audio Connections
- 6.9 Signal Connections
- 6.10 Data Connections
- 6.11 Powering Up
- 6.12 Configurator Software Installation
- 6.13 Product Modifications
- Replacement Parts
- Theory of Operation
- Index
Installation 6-16PTX-PRO User and Technical Manual
Figure 6-17: Multipurpose Radio and Wayside Data Cable
9
9
5
5
1
1
6
6
1
1
6
6
9
9
5
5
5
5
1
1
6
6
9
9
RED
RED
WHT
WHT
5
5
7
7
6
6
4
4
3
3
2
2
1
1
8
8
9
9
9
9
8
8
1
1
2
2
3
3
4
4
6
6
7
7
5
5
9
9
8
8
1
1
2
2
3
3
4
4
6
6
7
7
5
5
WHT
WHT
RED
RED
BLK
BLK
RADIO (M)
RADIO (M)
WAYSIDE (F)
WAYSIDE (F)
RADIO (M)
RADIO (M)
WAYSIDE (F)
WAYSIDE (F)
RADIO/WAYSIDE
RADIO/WAYSIDE
(F)
(F)
RADIO/
RADIO/
WAYSIDE (F)
WAYSIDE (F)
6.11 Powering Up
When the wiring and mounting are completed, it is time to power
up the PTX-PRO. As good practice, you should make a final
check before power is applied.
6.11.1 Checks before power-up
Here are your final pre-power-up checks:
• Double check to be sure all the cables are connected to
the correct connectors.
• Make sure the connections are all fully mated and locked.
CAUTION
Be sure the power being supplied matches
the power required by the equipment.
6.11.2 Initial power-up
Now you are ready to apply power:
1. Verify the power cable is properly connected to the front
panel power connector.