User Manual
Table Of Contents
- Notices
- Contents
- Introduction
- Product Description
- Routine Operation
- 3.1 Chapter Overview
- 3.2 Overview of Controls, Indicators and Connectors
- 3.3 Preparing for Operation
- 3.4 Using the Display Screens
- 3.5 PTX-PRO Monitoring Operations
- 3.6 PTX-PRO Control Operations
- 3.7 Front Panel vs. Configurator Settings
- Troubleshooting
- Advanced Operation
- 5.1 Chapter Overview
- 5.2 Before You Begin
- 5.3 Create or Update a Configuration
- 5.3.1 Using the Configurator Software
- 5.3.2 Determine Licensed Options
- 5.3.3 Create New Configuration On-Line
- 5.3.4 Load and Modify Configuration Settings On- Line
- Figure 5-7: Load and Modify Configuration Settings On-Line - Sheet 1 of 5
- Figure 5-8: Load and Modify Configuration Settings On-Line - Sheet 2 of 5
- Figure 5-9: Load and Modify Configuration Settings On-Line - Sheet 3 of 5
- Figure 5-10: Load and Modify Configuration Settings On-Line - Sheet 4 of 5
- Figure 5-11: Load and Modify Configuration Settings On-Line - Sheet 5 of 5
- 5.3.5 Load Configuration File into Radio On-Line
- 5.3.6 Change Preset Names in On-Line Mode
- 5.3.7 Create Channel Plan Offline
- 5.3.8 Modify Channel Plan in Offline Mode
- 5.3.9 Load and Modify a Channel Plan On-Line
- 5.3.10 Load Channel Plan File into Radio On-Line
- 5.3.11 Add Licensed Option
- Installation
- 6.1 Chapter Overview
- 6.2 Unpacking
- 6.3 Initial Inspection
- 6.4 Damage in Shipment
- 6.5 Mounting and Cabling
- 6.6 Power Connections
- 6.7 Grounding
- 6.8 Audio Connections
- 6.9 Signal Connections
- 6.10 Data Connections
- 6.11 Powering Up
- 6.12 Configurator Software Installation
- 6.13 Product Modifications
- Replacement Parts
- Theory of Operation
- Index
Installation 6-4PTX-PRO User and Technical Manual
Figure 6-3: Quick Release Mount on Non-MRC Tripod
Mounting - Non-MRC Tripod (Option 3) A third option is
available to mount a PTX-PRO to a non-MRC tripod that
contains a QuickSet tripod mount. This option requires the use
of a QuickSet Quick Change Adapter. The Quick Change
Adapter is attached to the bottom of the PTX-PRO using four
1/2-inch long, #6-32, pan head screws, lock washers, and flat
washers.
The Quick Change Adapter and PTX-PRO assembly is then
attached to the QuickSet tripod mount and is secured with the
tripod mount locking clamp. See Figure 6-4.
Flat Head Screws
(4 Each)
Quick
Release
Mount
Dovetail Adapter
Plate (Attached to
PTX-PRO)
Tripod
Mount
Figure 6-4: Quick Change Adapter on QuickSet Tripod
Mount - Typical
Final Mounting When the PTX-PRO is mounted on the tripod,
the antenna is typically attached to the Antenna Lock Plate
mounted on the PTX-PRO. See Figure 6-5 on page 6-5.
Pan Head Screws,
Lock Washers, and
Flat Washers (4 Each)
Tripod Mount
Locking Clamp
QuickSet Quick
Change Adapter
(Attached to PTX-
PRO)
QuickSet
Tripod
Mount