User Manual
Table Of Contents
- Notices
- Contents
- Introduction
- Product Description
- Routine Operation
- 3.1 Chapter Overview
- 3.2 Overview of Controls, Indicators and Connectors
- 3.3 Preparing for Operation
- 3.4 Using the Display Screens
- 3.5 PTX-PRO Monitoring Operations
- 3.6 PTX-PRO Control Operations
- 3.7 Front Panel vs. Configurator Settings
- Troubleshooting
- Advanced Operation
- 5.1 Chapter Overview
- 5.2 Before You Begin
- 5.3 Create or Update a Configuration
- 5.3.1 Using the Configurator Software
- 5.3.2 Determine Licensed Options
- 5.3.3 Create New Configuration On-Line
- 5.3.4 Load and Modify Configuration Settings On- Line
- Figure 5-7: Load and Modify Configuration Settings On-Line - Sheet 1 of 5
- Figure 5-8: Load and Modify Configuration Settings On-Line - Sheet 2 of 5
- Figure 5-9: Load and Modify Configuration Settings On-Line - Sheet 3 of 5
- Figure 5-10: Load and Modify Configuration Settings On-Line - Sheet 4 of 5
- Figure 5-11: Load and Modify Configuration Settings On-Line - Sheet 5 of 5
- 5.3.5 Load Configuration File into Radio On-Line
- 5.3.6 Change Preset Names in On-Line Mode
- 5.3.7 Create Channel Plan Offline
- 5.3.8 Modify Channel Plan in Offline Mode
- 5.3.9 Load and Modify a Channel Plan On-Line
- 5.3.10 Load Channel Plan File into Radio On-Line
- 5.3.11 Add Licensed Option
- Installation
- 6.1 Chapter Overview
- 6.2 Unpacking
- 6.3 Initial Inspection
- 6.4 Damage in Shipment
- 6.5 Mounting and Cabling
- 6.6 Power Connections
- 6.7 Grounding
- 6.8 Audio Connections
- 6.9 Signal Connections
- 6.10 Data Connections
- 6.11 Powering Up
- 6.12 Configurator Software Installation
- 6.13 Product Modifications
- Replacement Parts
- Theory of Operation
- Index
Installation 6-3PTX-PRO User and Technical Manual
Note
The versatility of the Quick Release Mount and a
mating Dovetail Adapter Plate allow the Dovetail
Adapter Plate to be attached to the bottom of the
PTX-PRO and the Quick Release Mount to be
attached to a non-MRC tripod, or vice versa. The
method you use to attach the PTX-PRO to a non-
MRC tripod is your choice.
Optional mounting procedures and illustrations to
mount your PTX-PRO on non-MRC tripods are
provided in the following paragraphs.
Mounting - Non-MRC Tripod (Option 1) To mount a PTX-PRO
on a non-MRC tripod, one option is to attach the Quick Release
Mount to the bottom of the PTX-PRO using four 1/2-inch long,
#6-32, flat head screws.
The Dovetail Adapter Plate is then attached to the non-MRC
tripod and the Quick Release Mount and PTX-PRO assembly is
attached to the Dovetail Adapter Plate on the tripod mount.
See Figure 6-2.
Figure 6-2: Dovetail Adapter Plate on Non-MRC Tripod
Mounting - Non-MRC Tripod (Option 2) To mount a PTX-PRO
on a non-MRC tripod, another option is to attach the Dovetail
Adapter Plate to the bottom of the PTX-PRO using four 1/2-inch
long, #6-32, flat head screws.
The Quick Release Mount is then attached to the non-MRC
tripod and the Dovetail Adapter Plate and PTX-PRO assembly is
attached to the Quick Release Mount on the tripod mount. See
Figure 6-3 on page 6-4.
Quick Release
Mount (Attached to
PTX-PRO)
Flat Head Screws
(4 Each)
Dovetail
Adapter
Plate
Tripod
Mount