User Manual
Table Of Contents
- Notices
- Contents
- Introduction
- Product Description
- Routine Operation
- 3.1 Chapter Overview
- 3.2 Overview of Controls, Indicators and Connectors
- 3.3 Preparing for Operation
- 3.4 Using the Display Screens
- 3.5 PTX-PRO Monitoring Operations
- 3.6 PTX-PRO Control Operations
- 3.7 Front Panel vs. Configurator Settings
- Troubleshooting
- Advanced Operation
- 5.1 Chapter Overview
- 5.2 Before You Begin
- 5.3 Create or Update a Configuration
- 5.3.1 Using the Configurator Software
- 5.3.2 Determine Licensed Options
- 5.3.3 Create New Configuration On-Line
- 5.3.4 Load and Modify Configuration Settings On- Line
- Figure 5-7: Load and Modify Configuration Settings On-Line - Sheet 1 of 5
- Figure 5-8: Load and Modify Configuration Settings On-Line - Sheet 2 of 5
- Figure 5-9: Load and Modify Configuration Settings On-Line - Sheet 3 of 5
- Figure 5-10: Load and Modify Configuration Settings On-Line - Sheet 4 of 5
- Figure 5-11: Load and Modify Configuration Settings On-Line - Sheet 5 of 5
- 5.3.5 Load Configuration File into Radio On-Line
- 5.3.6 Change Preset Names in On-Line Mode
- 5.3.7 Create Channel Plan Offline
- 5.3.8 Modify Channel Plan in Offline Mode
- 5.3.9 Load and Modify a Channel Plan On-Line
- 5.3.10 Load Channel Plan File into Radio On-Line
- 5.3.11 Add Licensed Option
- Installation
- 6.1 Chapter Overview
- 6.2 Unpacking
- 6.3 Initial Inspection
- 6.4 Damage in Shipment
- 6.5 Mounting and Cabling
- 6.6 Power Connections
- 6.7 Grounding
- 6.8 Audio Connections
- 6.9 Signal Connections
- 6.10 Data Connections
- 6.11 Powering Up
- 6.12 Configurator Software Installation
- 6.13 Product Modifications
- Replacement Parts
- Theory of Operation
- Index
Advanced Operation 5-19PTX-PRO User and Technical Manual
5.3.9 Load and Modify a Channel Plan On-Line
The flowchart required to load a channel plan in your radio and to
modify the plan in the on-line mode is contained in Figure 5-16.
Figure 5-16: Load and Modify a Channel Plan On-Line
MRC Configurator Icon
Main Page
Channel Plan Tab
Center
Modify center
frequency for
each channel, as
required
Currently
Selected Band
Verify Currently
Selected Band is
High Band (13
GHz)
Load Current
Band from Radio
Current selected
band is loaded
into the
Configurator
Offset +
Modify plus offset
frequency for
channel 1 thru
21, as required
Offset -
Modify minus
offset frequency
for channel 2 thru
22, as required
Radio Control
COM Port Menu
Select COM port
required
Connect
Radio Mode,
MPEG, COFDM,
LMS-T, Channel
Plan, and
Licensing Tabs
are displayed
Program Current
Band to Radio
Program All
Bands to Radio
Orr
Main Tab Radio Control Disconnect
Close
Configurator
window
Current selected
band is loaded
into the radio
The High Band
(13 GHz) channel
plan is loaded
into the radio
Save Bands
to Flie
Save
Configuration
File window is
displayed
Save file
And/Orr
Note
When Save Bands to File is selected, only
channel plan settings are saved to a file. No
Preset settings are saved to the file.
When Program Current Band to Radio or
Program All Bands to Radio is selected, only
channel plan settings are programmed into the
radio. No Preset settings are programmed into
the radio.