User Manual
Table Of Contents
- Notices
- Contents
- Introduction
- Product Description
- Routine Operation
- 3.1 Chapter Overview
- 3.2 Overview of Controls, Indicators and Connectors
- 3.3 Preparing for Operation
- 3.4 Using the Display Screens
- 3.5 PTX-PRO Monitoring Operations
- 3.6 PTX-PRO Control Operations
- 3.7 Front Panel vs. Configurator Settings
- Troubleshooting
- Advanced Operation
- 5.1 Chapter Overview
- 5.2 Before You Begin
- 5.3 Create or Update a Configuration
- 5.3.1 Using the Configurator Software
- 5.3.2 Determine Licensed Options
- 5.3.3 Create New Configuration On-Line
- 5.3.4 Load and Modify Configuration Settings On- Line
- Figure 5-7: Load and Modify Configuration Settings On-Line - Sheet 1 of 5
- Figure 5-8: Load and Modify Configuration Settings On-Line - Sheet 2 of 5
- Figure 5-9: Load and Modify Configuration Settings On-Line - Sheet 3 of 5
- Figure 5-10: Load and Modify Configuration Settings On-Line - Sheet 4 of 5
- Figure 5-11: Load and Modify Configuration Settings On-Line - Sheet 5 of 5
- 5.3.5 Load Configuration File into Radio On-Line
- 5.3.6 Change Preset Names in On-Line Mode
- 5.3.7 Create Channel Plan Offline
- 5.3.8 Modify Channel Plan in Offline Mode
- 5.3.9 Load and Modify a Channel Plan On-Line
- 5.3.10 Load Channel Plan File into Radio On-Line
- 5.3.11 Add Licensed Option
- Installation
- 6.1 Chapter Overview
- 6.2 Unpacking
- 6.3 Initial Inspection
- 6.4 Damage in Shipment
- 6.5 Mounting and Cabling
- 6.6 Power Connections
- 6.7 Grounding
- 6.8 Audio Connections
- 6.9 Signal Connections
- 6.10 Data Connections
- 6.11 Powering Up
- 6.12 Configurator Software Installation
- 6.13 Product Modifications
- Replacement Parts
- Theory of Operation
- Index
Advanced Operation 5-10PTX-PRO User and Technical Manual
5.3.4 Load and Modify Configuration Settings On- Line
The flowchart required to load Preset configuration settings and channel
plans from the radio and to modify the settings in the on-line mode is
contained in Figure 5-7 thru Figure 5-11.
Figure 5-7: Load and Modify Configuration Settings On-Line - Sheet 1 of 5
MRC Configurator Icon
Main Page
Radio Control
COM Port menu
Select COM
port required
Connect
Radio Mode,
MPEG,
COFDM, LMS-
T, Channel
Plan, and
Licensing
Tabs are
displayed
Load All Settings
from Radio
All Preset settings
and channel plans
are loaded into the
Configurator
Preset Operations
Change Preset
Names
Change Preset
Names Menu
Enter Preset
Names (12
characters
max)
Radio Mode Tab
Back Off (dB)
Enter back off
attenuation for
each Preset to
be modified
Color Bars
Select new
Color Bars
option for each
COFDM and
LMS-T Preset
to be modified
IF/CW Tone
Select new
IF/CW Tone
option for each
COFDM Preset
to be modified
Operation Mode
Select new
Operation
Mode option
for each Preset
to be modified
Remember Last
PA State Check
Box
Select check
box, as
required
A
Select Preset
Preset
Operations
Or-
Active Preset
Menu
Select Preset
required
Load Preset
Only the selected
Preset is loaded
into the
Configurator
To
Figure
5-8