User Manual
Table Of Contents
- Notices
- Contents
- Introduction
- Product Description
- Routine Operation
- 3.1 Chapter Overview
- 3.2 Overview of Controls, Indicators and Connectors
- 3.3 Preparing for Operation
- 3.4 Using the Display Screens
- 3.5 PTX-PRO Monitoring Operations
- 3.6 PTX-PRO Control Operations
- 3.7 Front Panel vs. Configurator Settings
- Troubleshooting
- Advanced Operation
- 5.1 Chapter Overview
- 5.2 Before You Begin
- 5.3 Create or Update a Configuration
- 5.3.1 Using the Configurator Software
- 5.3.2 Determine Licensed Options
- 5.3.3 Create New Configuration On-Line
- 5.3.4 Load and Modify Configuration Settings On- Line
- Figure 5-7: Load and Modify Configuration Settings On-Line - Sheet 1 of 5
- Figure 5-8: Load and Modify Configuration Settings On-Line - Sheet 2 of 5
- Figure 5-9: Load and Modify Configuration Settings On-Line - Sheet 3 of 5
- Figure 5-10: Load and Modify Configuration Settings On-Line - Sheet 4 of 5
- Figure 5-11: Load and Modify Configuration Settings On-Line - Sheet 5 of 5
- 5.3.5 Load Configuration File into Radio On-Line
- 5.3.6 Change Preset Names in On-Line Mode
- 5.3.7 Create Channel Plan Offline
- 5.3.8 Modify Channel Plan in Offline Mode
- 5.3.9 Load and Modify a Channel Plan On-Line
- 5.3.10 Load Channel Plan File into Radio On-Line
- 5.3.11 Add Licensed Option
- Installation
- 6.1 Chapter Overview
- 6.2 Unpacking
- 6.3 Initial Inspection
- 6.4 Damage in Shipment
- 6.5 Mounting and Cabling
- 6.6 Power Connections
- 6.7 Grounding
- 6.8 Audio Connections
- 6.9 Signal Connections
- 6.10 Data Connections
- 6.11 Powering Up
- 6.12 Configurator Software Installation
- 6.13 Product Modifications
- Replacement Parts
- Theory of Operation
- Index
Troubleshooting 4-7PTX-PRO User and Technical Manual
Table 4-6: General System Problems
Problem Possible Cause Suggested Operator Action Suggested Technical Staff Action
General System Problems
PWR LED on PTX-
PRO is off when PWR
switch is set to on ( I ).
Missing input power. • Make sure power cable is
connected properly.
• Verify power source is turned
on.
• Contact technical staff.
• Check input power voltage.
• Check both AC and DC power fuses.
• Call MRC Technical Support.
PWR LED on PTX-
PRO is amber.
PTX-PRO is indicating a Minor
Alarm.
• Check all Monitor Screens on
PTX-PRO display.
Troubleshoot per Section 4.3
on page 4-2.
• Check Error Code Screen on
PTX-PRO display.
Troubleshoot per Section 4.4
on page 4-3.
• Error messages: Troubleshoot per
Section 4.3 on page 4-2.
• Error Codes: Troubleshoot per Section 4.4 on
page 4-3.
• Call MRC Technical Support.
PWR LED on PTX-
PRO is red.
PTX-PRO is indicating a Major
Alarm.
TURN OFF POWER and call for
service.
Call MRC Technical Support.
4.6 Configurator Troubleshooting
This section provides information so you can troubleshoot and
correct problems that may arise when using the Configurator.
4.6.1 Configurator Error Messages
The Configurator has an extensive set of self-diagnostics that
will alert you when an operation cannot be completed.
When there is a problem, a message will appear in the
Configurator message area describing the problem. If the
Configurator encounters a major error, a pop-up window may be
displayed. Close the error message window by clicking OK.
Table 4-7 on page 4-8 provides the most common MRC Radio
Configurator error messages and what to do if they occur.