Table of Contents 1. Safety Instructions 2. The Projector ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 2 2.1 Features 2 2.2 Accessories 3 2.3 Appearance 4 3. Setting up the Projector ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 6 3.1 How to connect the projector 6 3.2 Turning on/off the projector 8 3.
1. Safety instructions Before you use the projector, please read this manual thoroughly and comply with the safety instructions hereunder. Improper use may cause fire, electric shock, injuries, or reduce the life of your projector. Warning: Ensure the projector is grounded properly by connecting the power cord to a grounded AC outlet. Do not defeat the safety purpose of the grounding type plug. Warning: Do not cover the lens when the lamp is on.
2. The projector 2.1 Features Receives signals with resolution up to 1280x1024,75 Hz. To ensure the output quality, please adjust the setup of your computer display card to be less than or equal to 1280x1024. Compact size — only 3.5 lbs. Incorporates TI single chip 0.7” DLPTM technology. Users may replace 150W (VIP R150/P16) lamp easily. Compatible with Mac/IBM PC. Compatible with NTSC/NTSC4.43/PAL/PAL-M/PAL-N/HDTV.
2.2 Accessories Please check if the following accessories are in the box. If any item is missing, please contact your dealer immediately.
2.
Foot Adjuster ＭＸ３ ｍａｎｕａｌ．ｐ６５ 6 Foot Adjuster button 02-12-17, 16:39
3. Setting up the projector 3.1 How to connect the projector Depending on your purpose, you can select any of the following connection methods. 1) For displaying data only Find the M1DA-VGA+USB cable; connect M1DA connector to the main body; and connect the VGA and USB connectors to the computer. Take note that with such a connection, the video and audio functions will not be available.
Use the Video Enhanced Adapter, and choose from the terminals below to connect. 1. 2. 3. 4. 5.6 7. Power cord VGA signal input terminal USB mouse control S-Video signal input terminal Composite Video signal input terminals PC Audio In/Out terminals Notes Connecting to a computer 1. Make sure that both projector and computer are turned off. 2. Plug the USB cable into the computer. 3. Plug one end of the VGA cable into the projector. 4. Plug the other end into the computer. 5.
Turning on the projector 1. Remove the lens cover. 2. Make sure the signal cables are connected. 3. Plug-in the power cord; the LED indicator will flash slowly. 4. Press the Standby key on the remote control or control panel to turn on the projector. The LED indicator stays on steady at this time. 5. The message “Warming up! Please wait.” appears on the screen of the projector. Please wait for 20 seconds or press the Menu key. The projector will detect the input signal source automatically. 6.
3.3 Adjusting the height of the projected image Foot Adjuster Button Foot Adjuster Please use the foot adjuster to adjust the height of the projector. Higher 1. Hold the foot adjuster button. 2. Raise the projector to the desired height by moving the foot adjuster; then release the foot adjuster button. Lower 1. Hold the foot adjuster button. 2. Lower the projector to the desired height by moving the foot adjuster; then release the foot adjuster button.
3.4 Adjusting the focus and zoom You can zoom in or zoom out the image with the zoom ring. To enlarge the image size, turn the zoom ring counterclockwise. To reduce the image size, turn the zoom ring clockwise. To adjust the focus of the image, turn the focus ring until the image becomes clear. The projection distance of the projector is 4’7” ~ 32’9” (1.4 ~ 10 meters).
3.
4. How to use the projector This section covers how to use and adjust the projector, as well as how to use the control panel, remote control, and menu. 4.1 Initial image adjustment 1 Follow the previously stated steps to turn on the projector; and keep the projector facing the screen. 2 Turn the zoom ring to adjust the size of the image. 3 Turn the focus ring to adjust the focus of the image. 4 Use the foot adjuster to adjust the height of the image.
LED Indicator When the projector is turned on, the LED indicator flashes. Press the Standby key to display the image. After a few moments, the LED indicator stays on steady. If the LED indicator flashes quickly, the projector is most likely in an abnormal condition. Possible reasons include: a. If the fan is in an abnormal condition, the message “Fan lock error occurred, Projector shutting down!” appears on the screen. b.
- Remote Control Key Freeze/Esc/L Enter/R Stand By Mode ＭＸ３ ｍａｎｕａｌ．ｐ６５ Functions Press this key to freeze the image. Press again to clear the static image. Press this key to quit the menu if the menu is on the screen. In the remote-control mouse mode, this key works as the left key of the mouse. Please check page 13, “Enter/Sync” of “Control panel”, for the use of this key on the menu. In the remote-control mouse mode, this key works as the right key of the mouse.
Menu Source Blank Please refer to page 13, “Menu” of “Control panel”. Select Analog RGB, Analog Y Pb Pr, Digital RGB, Composite Video, S-Video and Component Video signals in sequence. Convert the image into blank and fully blue. Press again Pg.Up to restore. Press this key to adjust the phase and frequency automatically. In remote control mode, press this key to zoom in the image (*). When the mouse is in use, press this key to turn to the previous page. Pg.
5. Menu Press the Menu key to open the menu. You can press the up or down key to select the items on the menu; or press Esc to quit the menu. To enter the submenu, please press the Enter key or the right arrow key. On the submenu, press the Menu or Esc key on the remote control to return to the main menu; or press twice to quit the menu. 5.1 Image (VGA mode) Submenu Brightness Contrast Keystone Color Temp Zoom Purpose Using To adjust the brightness of image Press key to decrease brightness.
5.2 Image (Video mode) Submenu Brightness Contrast Color Hue Saturation Sharpness Purpose Using Press key to decrease image. brightness. Press key to increase brightness. (*) To control the balance between Press key to decrease the brightest and darkest parts contrast. of the image. You can change the Press key to increase amount of black and white. contrast. (*) To change the image from black Press key to decrease & white to saturated colors. the amount of colors in the image.
5.3 Display (VGA mode) Submenu Frequency Phase Purpose To adjust the frequency of data display to be the same as the frequency of display card of computer. Use this function to correct the flickering vertical lines shown in the image. Using Press key for To synchronize the signals of Press key for images and display cards. Use this function to correct adjustment (*) adjustment (*) inconsistent or flickering images.
5.4 Display (Video mode) Submenu Keystone Purpose To modify the biased image Using Press key to reduce resulting from the improper angle of the projector. the length of the lower screen. Press key to reduce the length of the upper screen. (*) Color Temp To adjust the color temperature in the range between 6500K and 9200K. Factory default is 7700K. Press key to lower color temperature,the image looks warmer. Press to increase color temperature; the image looks cooler.
5.5 Audio Submenu Volume Purpose or Using Press key to turn down the volume. Press key to turn up the volume. (*) Treble Press key to decrease the volume of treble. Press key to increase volume of treble. Bass (*) To adjust the medium/low frequency of audio. Press key to decrease bass. Press key to increase bass. Mute (*) Select ”Yes” for Mute (Press right key). * Press the Auto key to return to previous setup.
5.6 Management Submenu OSD Location Purpose Using To display the position of the Press key for menu on the screen. Projection (Projection before the Screen) selection (*) Press key for selection (*) Default (Projection behind the Screen) If you select this function, the projector will reverse images from left to right or vice versa. Thus the image can be projected from behind onto the semi-transparent screen.
Lamp Reset To recount hours after replacing the lamp. Press the right key. The message “Press Enter key to confirm lamp reset operation!” appears. Please check if the user has replaced the new lamp. If yes, press Enter key. If not, press Menu key or Esc key on the remote control to quit. Reset All To return to the factory default. Press the right key. Source Type To select RGB, Digit RGB, Press key for YPbPr or Auto Scan source. selection.
6. Maintenance 6.1 Replacing the lamp 30 hours before the end of the lamp’s life time, the warning message “Lamp life time is up! Replacement suggested!” will display on the screen. Please replace the lamp immediately. Steps: 1. Power off the projector. 2. Unplug the power cord. 3. Cool down the projector for at least 30 minutes. 4. Use a screwdriver to remove the shell and screws on the lamp. 5. Remove lamp.
7. Appendix 7.1 Common problems and troubleshooting If you are having a problem with your projector, please check the following situations described below. If you still cannot solve the problem, contact your local distributor or our service center. Q.: No image on the screen at all Make sure that you have properly connected the video enhanced adapter and the relevant cables mentioned in the previous chapters. Make sure the plug is not bent or broken.
Q.: Image becomes blurred Adjust the focus ring of the projector. Make sure that distance between the screen and projector is adequate (4’7” ~ 32’9” or 1.4 ~ 10 meters). Q.: The colors projected by your projector look different from the colors of your computer or VCR. This is not a problem. You can adjust the brightness, color or contrast on the menu to change colors. Q.: When the projector is connected to a DVD player, playing a film with the ratio 16:9, the image is reshaped.
7.2 Specifications Resolution XGA (1024*768), SXGA (1280*1024) compressed Lamp 150W VIP, 1500 hrs lamp life Brightness 1500 ANSI Lumens Size 229x193x69 mm Weight 3.5 lbs Image size 26.4mm (0.7 inches diagonal) Projection distance 4’7” ~ 32’9” (1.4 – 10 meters) Throw Ratio 1.34:1 ~ 1.6:1 (Distance: Diagonal) Zoom Ratio 1.2:1 (Manual Zoom/Focus) Uniformity 85% Aspect Ratio 4:3 / 16:9 screen selectable Contrast Ratio 900:1 Horizontal Frequency 31.
Input Terminal DVI (M1DA) USB RGB (M1DA-D-Sub 15 pin) RS232 (M1DA) Y/Pb/Pr (M1DA,VGA) S-Video Mini DIN 4 pin Audio: RCA Jack 3.5mm Mini Jack Composite Video (RCA Jack) Output Terminal 1watt speaker * All specifications are subject to change without notice. This device complies with Part 15 of the FCC Rules.
