Table of Contents Safty Declaration FCC Compliance Statement________________________ 1 Radio Frequency Interference Statement _____________ 2 Canadian DOC Notice ____________________________ 2 Important Safety Instructions________________________ 3 CHAPTER 1 Introduction ____________________________________ 5 Before Installing Your Monitor ______________________ 5 About Your Monitor ______________________________ 5 RGB Mode ____________________________________ 5 Factory-Preset Modes ________________________
18” LCD monitor FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. FCCWARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
18” LCD monitor Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit.
18” LCD monitor Important Safety Instructions Please read the following instructions carefully. This manual should be retained for future use. 1. To clean the LCD monitor screen, make sure the monitor is in the power off mode. Unplug the monitor from its power source before cleaning it. Do not spray liquid cleaners directly onto the unit. Stand away from the LCD monitor and spray cleaning solution onto a rag. Without applying excessive pressure, clean the screen with the slightly dampened rag. 2.
18” LCD monitor l U.S. : VW-1; 18AWG X 3C; SVT with national approval as UL and/or CSA approval/number(s) l Europe : VDE / Ö VE and/or KEMA approval; H05VV-F, 3G, 0.75mm , or equivalent. 2 The power cord should bear the name of the manufacturer and state the type of cord that it is.
18” LCD monitor CHAPTER 1 INTRODUCTION BEFORE INSTALLING YOUR MONITOR Read this manual carefully. PAY ATTENTION to all Warning and Caution messages. DO NOT use computer components not recommend by the manufacturer. Do not attempt to service the monitor yourself. If a problem occurs, contact the manufacturer's authorized service center. ABOUT YOUR MONITOR This monitor is a microprocessor-controlled, color monitor that uses a TFT LCD panel.
18” LCD monitor FACTORY-PRESET MODES Table 1 shows standard video mode settings that have been pre-adjusted at the factory for accurate video display. These setting are stored in the monitor's memory. Table 1. Factory-Preset Modes Mode NEC VGA SVGA XGA SXGA Macintosh Resolution 640x400 640x350 720x400 640x480 640x480 640x480 800x600 800x600 800x600 800x600 1024x768 1024x768 1024x768 1280x1024 1280x1024 640x480 832x624 1024x768 1024x768 H-Freq.(KHz) 24.83 31.47 31.47 31.47 37.86 37.5 35.16 37.88 48.
18” LCD monitor SPECIFICATIONS l 18” LCD Monitor Overall Dimension (HxWxD): Shipping Weight (G/W): Effective Display area (H/V): Display colors: Scan Frequencies: Horizontal Vertical Viewing Angle Contrast Ratio Response time ( Tr + Tf ) Native Resolution Pixel pitch: Power: Input Consumption Video Connector: RGB Signals: Video Sync Display Data Channel: Compatibility 426 x 444 x 215 mm 11Kg 359.04 x 287.23 mm 16.7M colors 31.47KHz to 80KHz 60Hz to 75Hz 160 /160 degree H/V 400:1 30ms 1280x1024(SXGA) 0.
18” LCD monitor Control Type: Compatibility: Environmental Limits: Operating Temp. Storage Temp.
18” LCD monitor CHAPTER 2 INSTALLING THE MONIT OR The monitor is equipped with an auto sensing power supply for voltage ranges from 110~240VAC, 60/50Hz. Confirm the line voltage designation on the rear panel of the monitor. FOLLOW THESE STEPS T O INSTALL THE MONITOR 1. Before you connect the cables, make sure that the monitor and the computers are both turned off. 2. Plug one end of the 15-pin signal cable to the monitor and the other end to the video signal connector at the rear of the system.
18” LCD monitor 10
18” LCD monitor C ONTROL F UNCTIONS The Monitor control functions are located on the lower right side of the front part of the monitor, just below the glass. The control functions are shown in the figure below and described in the following paragraphs. The control key description: 1. : Power Switch 2. - / + : Decrease / increase 3. Sel : Cursor Down 4. MENU : Activates the OSD (on-screen display) function 5.
18” LCD monitor Description 1. : Power switch Use the power switch to turn power ON or OFF. We recommend turning your system power on first before turning on the monitor 2. - & + : Decrease/increase The two keys work to decrease or increase the value of the selected item. 3. Sel : Select key This key is used to select the items or functions to be adjusted. 4. Menu Press the Menu key to activate the OSD (on-screen display) screen; this is a toggle key. Press twice to turn off the OSD screen.
18” LCD monitor CHAPTER 3 ADJUSTING THE MONITOR The LCD monitor is designed to work with a range of compatible video adapters on the market. Due to the possible deviations between these video adapters, you may make some adjustment to fit the monitor for adapter used. ADJUSTMENT PROCEDURE 1.
18” LCD monitor 2. Use the Sel key to select the required adjustment item down. 3. Use the - & + key to do the desired function or go into the second menu item to do the further change. AUTO-ADJUSTMENT WE STRONGLY RECOMMEND THAT YOU USE THIS ITEM TO GET THE OPTIMIZED VISUAL QUALITY. Use the Select key to select auto-adjustment, then press - & + to get the optimized quality.
18” LCD monitor Adjust the contrast value l Use the Sel key to select the CONTRAST item, then press - & + to get the best contrast optimization. You can adjust R,G,B simultaneous or separate R,G,B value. (You can use this item to change the RGB purity.) Color Balance l Use the Sel key to select the balance item, then press - & + to get the best color balance effect or separate set the RGB color value.
” LCD monitor VERTICAL & HORIZONTAL POSITION ADJUSTMENT 1. Use the Sel key to move to the ICON, then press - & + to move the whole screen left or right to the center position. 2. Use the Sel key to move to the ICON, then press - & + to move the whole screen down or up to the center position. ADJUST THE VIEWING SCREEN SIZE l Use the Sel key to move to the icon, then press - & + to get the larger viewing size. PHASE ADJUSTMENT Adjust phase tracking of display signal to reduce the display flicker.
18” LCD monitor DOS/GFX Now, you can select the display mode as 640x400 (called graphic mode), or 720x400 (called text mode). Color Temperature We provide three modes, one is user mode, one is 6500 and the other is 9300. Use the Select key to move to the color temperature, then press - & + to select the color temperature setting. When user set at 6500 or 9300, then the user can’t change the value. BRIGHTNESS Adjustment Use the Sel key to select the item, press - & + to change the brightness value.
18” LCD monitor Appendix Troubleshooting Procedures This LCD Monitor was pre-adjusted in the factory with standard VGA timing. Due to output timing differences among various VGA cards, you may initially experience an unstable or unclear display when a new display mode or new VGA card is selected. This LCD Monitor Supports Multiple VGA Modes. Refer to timing table for a listing of the factory-preset modes supported by this LCD Monitor.
18” LCD monitor 5. If the power LED is not lit, check to see if the AC power connector is securely connected. Verify that the AC adapter LED is lit. If the AC adapter LED is not lit, please contact your dealer for assistance.
