C593 15” LCD MONITOR USER’S MANUAL
Installing The Monitor Follow these steps to install the monitor, 1. Before you connect the cables,make sure that the monitor and the system unit power switches are OFF. 2. Please follow the following drawing to remove the plastic back over in order to connect the signal cable and power cable. 3. Plug one end of the 15pin signal cable to the monitor and the other end to the video signal connector at the rear of the system.
Content Operating Instructions ............................................................................ iv Safety Precautions ................................................................................... v Care and Maintenance ........................................................................... vi Control Functions ..................................................................................... 1 Adjustment Procedure .....................................................................
Operating Instructions Thank you for purchasing this high-resolution multi-scan color monitor. Please read this guide thoroughly before installation. FCC RADIO FREQUENCY INTERFERENCE STATEMENT WARNING: (FOR FCC CERTIFIED MODELS) This monitor has been tested and found compliant with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide proper protection against harmful interference to a residential installation.
Safety Precautions This monitor is manufactured and tested on the ground principle that a user’s safety comes first. However, improper use or installation may not only damage the monitor but endanger the user as well. As a safety precaution, go over the following WARNINGS carefully before installation, and keep this guide handy. Warnings: • This monitor should be operated only at the correct power sources indicated on the label at the rear end of the monitor.
Care and Maintenance Care • Avoid exposing your monitor directly to sunlight or other heat sources. Place your monitor away from the sun to reduce glare. • Put your monitor in a well-ventilated area. Do not place anything heavy on top of your monitor. • Make certain that your monitor is installed in a clean and moisture-free area. • Keep your monitor away from magnets, motors, transformers, speakers, and TV sets.
Control Functions The Monitor control functions are located on the lower center portion of the front panel. These are shown in the figure below and described in the following paragraphs. 1. : Power switch Use the power switch to turn power ON or OFF. We recommend turning your system power on first, then the LCD monitor 2. - & + : Decrement & Increment These two keys are used to decrease or increase the values of each selected item. 3.
Adjustment Procedure 1. Press the Menu key to activate the OSD screen. The screen below will appear. Note: Perform the procedure above whenever you need to change a setting. For the succeeding sections, this step will not be included, and users will be presumed to have performed the procedure. OSD SCREEN 1024X768 75Hz/60KHz AUTO ADJUSTMENT MENU MENU LANGUAGE MENU DOS/GFX OFF USER 100 VERSION XGAD9B11-5100 2. Use the selection key to move to the desired item. 3.
RGB Adjustment Use the selection key to select the icon, then press - or +. The screen below will appear. 1024X768 75 Hz/60 KHz Auto-Balance CONTRAST RED GREEN BLUE BALANCE RED GREEN BLUE 20 18 19 49 50 26 VERSION XGAD9B11-5100 Contrast Value Adjustment Use the selection key to select the CONTRAST field, then press - & + to get the best contrast optimization. You can adjust R,G,B simultaneously or adjust each Red, Green, and Blue channel separately.
Geometry Adjustment Use the selection key to select the icon, then press - & +. The screen below will appear. 1024X768 75 Hz/60 KHz 21 33 1344 49 PHASE VERSION XGAD9B11-5100 If you need to go back to the previous OSD menu screen, press the MENU key. Vertical & Horizontal Position Adjustment 1. Use the selection key to move to the icon, then press - & + to move the whole screen left or right to the center position. 2.
Multi-language support You can select five OSD languages for your convenience. 1024X768 75 Hz/60 KHz English German French Italian Spanish VERSION XGAD9B11-5100 DOS Txt/GFX You can select display mode as 640 x 400 (graphic mode) or 720 x 400 (text mode). Color Temperature Three modes are provided: User Mode, 6500, and 9300. Use the selection key to select the Color Temperature field, then press - & + to select the color temperature setting.
General Specifications LCD type: 15.0" XGA Color TFT Input Signal: Analog (0.7Vp-p/75 ohm positive) Screen area: 304.1 mm x 228.1 mm Dot Pitch: 0.297 mm Scanning frequency: (H) 31.46 KHz-60 KHz , (V) 60 Hz-75 Hz Resolution: 1024 x 768 Refresh Rate: 80 MHz (maximum) Display Color: 16.2M colors (dithering) Luminance: 200 cd/m2 (Typ.) Contrast Ratio: 350 (Typ.) Response Time: Rising time: Falling time: Typ.
General Performance Preset timing is shown as follows: Resolution H/V Frequency 640 x 480 60Hz/31.47KHz 800 640 x 480 72Hz/37.86KHz 832 640 x 480 75Hz/37.5KHz 840 800 x 600 56.3Hz/35.16KHz 1024 800 x 600 60.3Hz/37.88Khz 1056 800 x 600 72.2Hz/48/08KHz 1040 800 x 600 75Hz/46.87KHz 1056 1024 x 768 60Hz/48.36KHz 1344 1024 x 768 70Hz/56.47KHz 1328 1024x768 75Hz/60Khz 1312 720 x 400 70Hz/31.47KHz 900 640 x 350 70Hz/31.47Khz 800 640 x 400 70Hz/31.47KHz 800 1024 x 768 74.
