CONTENT Operating Instructions........................................................................ 1 Safety Precautions............................................................................... 3 Care and Maintenance......................................................................... 4 Getting Start....................................................................................... 5 Description of Controls......................................................................
Operating Instructions Thank you for purchasing this high-resolution multiscan color monitor. Please read this guide thoroughly before installation. FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.
Class BITE (Following European standard EN 50082-2) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications.
Safety Precautions This monitor is manufactured and tested on the ground principle that a user’s safety comes first. However, improper use or installation may not only damage the monitor but endanger the user as well. As a safety precaution, go over the following WARNINGS carefully before installation, and keep this guide handy. WARNINGS: l This monitor should be operated only at the correct power sources indicated on the label at the rear end of the monitor.
Care and Maintenance Care l Avoid exposing your monitor directly to sunlight or other heat sources. Place your monitor away from the sun to reduce glare. l Put your monitor in a well ventilated area. Do not place anything heavy on top of your monitor. l Make certain that your monitor is installed in a clean and moisture-free area. l Keep your monitor away from magnets, motors, transformers, speakers, and TV sets.
Getting Start Introduction Brilliant and sharp images of text and graphics — that’s what this LCD color monitor offers. This LCD monitor features user-friendly OSD controls. This LCD monitor provides a maximum resolution of 1024 x 768 pixels with a flicker-free display at up to 75Hz refresh rates, which offers the ultimate comfort to your eyes. Its 15.0” diagonal measurement makes the display area close to the standard 17” CRT display.
Unpacking and Checking the Package Contents Before unpacking your LCD Monitor, prepare a suitable workspace for your LCD Monitor and computer. You need a stable, level and clean surface near a wall outlet. After unpacking your LCD Monitor, make sure that the accessories shown in the packing list are included in the package. If anything is missing or damaged, please contact your dealer or nearest regional office.
Description of Controls Stand the monitor up and remove the back cover from your monitor (pull from the bottom of cover outward to open it) for further installation with your PC system.
uSignal cable vDC Jack wAudio in (optional) xAudio out (optional) j OSD OUT Button kt Arrow key Connect with PC Video card Plug into the AC power adapter. Connect with your audio device. Connect with speakers built-in monitor base. Exit the OSD(On Screen Display). Press to bring up the On Screen Display and select main menu items. lu Arrow key Press to bring up the On Screen Display and select sub menu items. m“-” Minus key Adjust setting bars of Contrast, Brightness, etc. to decrease setting values.
Connecting Your Monitor to the PC Connecting AC Power Please refer to the following instructions for connecting AC power to the LCD Monitor. l Remove the back cover from your monitor (pull from the bottom of cover outward to open it). l Plug the female end of the 1.8m power cord into the AC adapter then plug the DC connector of the adapter to your monitor’s DC jack (the DC jack is located at the rear side of your monitor) l Connect the male end of the power cord into a wall socket.
Connecting Video l Turn off your PC and the LCD Monitor before connecting your LCD monitor to the PC. l Use the built-in 1.8M-signal cables to connect your LCD Monitor with PC. l Connect the other end of the signal cable to the PC’s VGA port. l Make sure the signal cable head is securely connected to the PC’s VGA port. Then tighten the connecting screws to ensure a secure connection. l Turn on your computer. l Turn on your LCD Monitor.
Operating the Monitor The LCD monitor has been preset at the factory with the Timing to create the optimal picture. You are also able to adjust the picture as you like by following operation. Before you operate your monitor, please take a look at the definition of each function key. How to Use the OSD (On Screen Display) OSD functions enable you to easily adjust the display to reach the quality you like. The OSD menus include the main menu and sub-menus. Structure of OSD Menus Operating Procedure 1.
Menu Table Main Menu Function Name After pressing “+” and “-“ buttons BRIGHTNESS The brightness is adjusted. CONTRAST BL BLACK LEVEL The contrast is adjusted. The level of the black portion is adjusted. The screen is expanded or shrunk in the left and CLOCK CLOCK PHASE right direction. The screen is periodically changed. HORIZONTAL POSITION The screen is moved to left or right.
Adjusting screen display There are two ways to adjust the monitor’s screen, i.e. auto adjustment and manual adjustment. Auto adjustment a) Power ON the LCD monitor and computer. b) Select the “AUTO SETUP” of OSD screens. c) Press “+” button while displaying “AUTO SETUP” screen. d) The auto adjustment is started. “AUTO SETUP” will be displayed during auto adjustment. It takes about 10 seconds to finish adjustment.
Manual adjustment a) Power ON the LCD monitor and computer. b) Adjust according to the above-mentioned “Operating Procedure” and “Menu Table” to adjust the screen to a favorable screen display. OSD Adjustment Lock This function is used to prevent changing the adjusted status by mistake. All the adjustable items except “BRIGHTNESS” will be locked. a)Press the “„” and “-“ buttons at the same time and the “CONTROL LOCK” screen is displayed.
d)Volume control: Press “+” and “-“ button to up/down audio volume 15
Specifications LCD panel Driving system Active matrix TFT Size Diagonal: 15.0” Pixel pitch 0.297mm(H)x 0.297mm(V) Resolution 1024 x 768 pixels Viewing angle (R+L) 120 (Typ.) Viewing angle(U+D) 100 (Typ.) Max. Response time Tr: 7 ms (Typ.
Supported Timing The monitor supports 14 kinds of timing. Display Mode VESA Horizontal Vertical Frequency Frequency 31.5 KHz 60 Hz VGA 640 x 480 37.5 KHz 75 Hz 720 x 400 31.5 KHz 70.1 Hz 35.1 KHz 56.3 Hz 37.9 KHz 60.3 Hz 46.9 KHz 75.0 Hz 48.1 KHz 72 Hz 48.4 KHz 60.0 Hz 56.5 KHz 70 Hz 58.1 KHz 72 Hz 60.0 KHz 75.0 Hz VGA 640 x 480 35.0 KHz 66.7 Hz 832 x 624 49.7 KHz 74.6 Hz 640 x 350 31.5 KHz 70.
Power Management The LCD Monitor complies with the VESA DPMS (version 1.0p) power management proposal. The VESA DPMS proposal provides four phases of power-saving modes by detecting the horizontal or vertical sync signal.
Troubleshooting Procedures If the LCD monitor fails to function correctly, please follow the following steps for possible troubleshooting. 1. Perform the adjustments according to Operating the Monitor.. 2. Refer to the following items if you cannot find a proper item listed in the Operating the Monitor or if the problem remains. 3.
Display is not synchronized. 4. The signal cable is properly connected. The signal timing of the computer is within the specs. The video output level of the computer is within the specs. While the “ATTENTION” message is displayed on the screen: It can be classified into two categories, i.e, Power Management is set to OFF and Power Management is set to ON. a)Power Management is set to OFF. l Check if the signal cable is connected correctly to the computer. l Check if the cable is broken.
