8" HIGH RESOLUTION WITH SUPER- WIDE VIEWING ANGLE USER'S MANUAL www.microtek.
Table of Contents Safety Declaration FCC Compliance Statement iii Radio Frequency Interference Statement iv Canadian DOC Notice v Chapter 1 Introduction 1 Precautions 1 Product Features 1 Unpacking 2 Specifications 3 Supported Timing 4 Cleaning 5 Chapter 2 Installing the Monitoe 6 Connecting the Monitor 7 Adjusting the Viewing Angle 8 Chapter 3 Operating the Monitor 9 How to Use the OSD 10 Structure of OSD Menus 10 Operating Procedure 10 i
Menu Table 11 Troubleshooting Procedures 13 For Your Safety 15 ii
FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
• Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit. The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. “Le présent appareil numérique n’èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.
Chapter 1 Introduction Precautions z z z z z z z z z z Read all of these warnings and save the manual for later use. Follow all warning and instructions on the product. Do not cover or block the vent holes in the case. Do not insert sharp objects or spill liquid into the LCD monitor through the cabinet slots; this may cause accidental fire, electric shock or failure. Disconnect the power plug from the AC outlet if you will not use it for an extended period of time.
Unpacking Before unpacking your LCD Monitor, prepare a stable, level, and clean surface near a wall outlet for your LCD Monitor. 1. 2. Set the LCD Monitor box in an upright position and open from the top of the box before removing the right/left cushions. Remove the back cover from your monitor (pull from the bottom of cover to open) to install your PC system.
Specifications LCD type 18” SXGA Color TFT Display Area 14.1 x 11.2 in. (357.1 x 285.7 mm) Input signal Analog (0.7Vp-p/75 ohm positive) Dot pitch 0.28mm Scanning frequency (H) 31.5~79.97 KHz, (V) 56.3~75.02 Hz Resolution 1280 x 1024 Display color 16.7M colors Luminance 250 cd/m2 Contrast ratio 350:1 Response time 30 ms(Typ.) Viewing angle (H) 160°/ (V) 160° Control type OSD Plug & Play VESA DDC 1/2B Dimension (H x W x D) 17.6 x 16.7 x 7.3 in.( 447 x 424.2 x 185.4 mm) Weight 12.
Supported Timing Analog Display Mode VGA Horizontal Frequency Vertical Frequency 31.5 KHz 60 Hz 37.5 KHz 75 Hz 31.5 KHz 70.1 Hz 35.2 KHz 56.3 Hz 37.9 KHz 60.3 Hz 46.9 KHz 75.0 Hz 48.1 KHz 72.0 Hz 48.4 KHz 60.0 Hz 56.5 KHz 70.1 Hz 60.0 KHz 75.0 Hz 63.98 KHz 60.02 Hz 79.97 KHz 75.02 Hz 640 x 480 35.0 KHz 66.7 Hz 832 x 624 49.7 KHz 74.6 Hz 640 x 350 31.5 KHz 70.
Cleaning WARNING z If you dropped any material or liquid such as water onto the monitor when cleaning, unplug the power cable immediately and contact your dealer or the nearest service center. Always make sure your hands are dry when unplugging the power cable. CAUTION z For safety reasons, turn-off the power switch and unplug the monitor before cleaning. z Do not scratch or rub the screen with a hard object. z Never use any of the following solvents on the LCD monitor.
Chapter 2 Installing the Monitor z DO NOT install the monitor where sudden temperature changes may occur, or in humid, dusty, or smoky areas as it may cause fire, electric shock or damage. z DO NOT place your LCD Monitor near a window as it may be severely damaged if exposed to rain, water, moisture, or sunlight. z MAINTAIN good ventilation; covering of ventilation slots or holes may cause fire.
Connecting the monitor 1. Turn off your PC and the LCD Monitor before connecting your LCD monitor to the PC. 2. Use VGA cable to connect the VGA connector of the LCD Monitor to the VGA port of the PC system. Make sure the cable head is securely connected. (Option: If your system is Dual signal model, then use the DVI cable to connect the DVI connector to the DVI port). 3. Use Audio cable to connect “Audio in” jack on LCD Monitor and sound card’s “Audio out” jack. 4.
NOTE: For added protection, it is X Audio in Connect with Audio cable. Protection device plugged between Y VGA connector Connect with VGA cable. the AC Adapter and the electrical wall Z Power outlet to prevent the effects of sudden [ DVI recommended to use a Surge connector (optional) current variations from reaching the LCD Monitor. Sudden peaks of Plug into the AC power adapter.
Chapter 3 Operating the Monitor Buttons 1 ○ AUTO 2 ○ e 3 ○ MENU 4 ○ f 5 ○ EXIT 6 ○ Power Switch Functions Automatically adjust image Clock, Phase, H-Position, V-Position settings Indicating the cursor movement or OSD manual selection in decremental values Pop up OSD Menu or Enter into sub menu Indicating the cursor movement or OSD manual selection in incremental values Exit OSD Menu and user setting saving Power ON/OFF the monitor/ Green – Normal operation Amber – Power Management 9
How to Use the OSD (On Screen Display) OSD function allows the user to easily adjust the display to the desired quality. The OSD menu includes a main menu and a sub-menu. Structure of OSD Menus Operating Procedure Use the buttons on the right side control panel to adjust the OSD 1. Power on the LCD monitor. 2. Press “MENU” button to pop up the OSD menu. 3. Press “e” or “ f” button to select menu item. 4. Press “MENU” button to select sub menu. 5. Press “e” or “ f” button to select sub menu item. 6.
Menu Table Main Menu Sub Function Name Situation/Option Menu All Reset Recall the all factory default settings.
Clock Adjust To correct flickering text or lines. Phase Adjust To correct flickering text or lines. H-Position Adjust screen horizontal position. V-Position Adjust screen vertical position.
Appendix A Troubleshooting Procedures If the LCD monitor fails to function correctly, please follow the following steps for a possible solution. 1. Perform the adjustments according to Operating the Monitor. 2. Refer to the following items if you cannot find a proper item listed in the Operating the Monitor or if the problem remains. 3.
Display is too dark or too bright. If the video output level of the computer is within the spec. Display is not If the signal timing of the computer is within the spec. in the center. Display is shaking. If the power voltage is within the spec. If the signal timing of the computer is within the spec. If the signal cable is properly connected. Display is not If the signal timing of the computer is within the spec. synchronized. If the video output level of the computer is within the spec.
Appendix B FOR YOUR SAFETY WARNING ALWLAYS OPERATE UNDER SPECIFIED POWER SUPPLY Usage of incorrect voltage will cause malfunction and may cause fire or electric shock. PROTECT and CORRECTLY USE THE CABLE Do not pull or bend the power cable and signal cable or place the monitor or any heavy objects on the cables. If the cables are damaged, they may cause fire or electric shock.
BAD WEATHER CONDITIONS It is advisable not to operate the monitor during heavy thunderstorms as intermittent breaks in power may cause malfunction. Do not touch the plug under these circumstances as it may cause electric shock. CAUTION DISCONNECT CABLES WHEN MOVING THE MONITOR When moving the monitor, always turn off the switch, unplug the monitor, and disconnect the signal cable. If the cables are not properly disconnected when moving the monitor, it may cause fire or electric shock.
SPECIAL NOTES ON LCD MONITORS The following are normal with LCD monitors and do not indicate a problem. z z z z z z When first turning on the LCD monitor, if the picture does not fit in the display area, it is because of the type of computer that is used. In such case, adjust the picture position to its correct position.(See Operating the Monitor) The screen may flicker during initial use. Turn off the power switch and then turn it on again the flickering should disappear.
