FCC Compliance Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. FCC Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
CE mark for Class B ITE (Following European standard EN55022/ 1998; EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
Table of Contents Introduction ................................................................................. 5 Product Features .................................................................... 5 Unpacking .............................................................................. 6 Precautions ............................................................................ 6 Cleaning ................................................................................. 7 Connecting the Monitor ...........
Introduction Congratulations on the purchase of your new LCD monitor! With a 20.1" TFT active matrix color crystal display and offering a maximum resolution of 1600 x 1200 pixels, your 20.1" LCD monitor offers sharp and vibrant color display with low radiation emission. And with its low power consumption, the monitor helps you reduce your power bill as well. Product Features • 20.
Unpacking Before unpacking your LCD monitor, prepare a stable, level, and clean surface near a wall outlet for the monitor. 1. Set the LCD monitor box in an upright position, and open from the top of the box before removing the right/left cushions. 2.
• Do not apply pressure to the screen, as the screen is very delicate. • Keep the monitor away from extremely hot, cold or humid places. • Do not place the monitor directly under sunlight, in dusty surroundings, or near equipment which may generate strong magnetic fields. Cleaning Warning: If you drop any material or liquid such as water onto the monitor when cleaning, unplug the power cable immediately and contact your dealer or the nearest service center.
Connecting the Monitor • Turn off your PC and the LCD monitor before connecting your LCD monitor to the computer. • Place the monitor on a flat and level surface. • Usage of incorrect voltage will cause malfunction and may cause fire or electric shock. • Do not pull or bend the power cable, or place the monitor or any heavy objects on the cables. If the cables are damaged, fire or electric shock may ensue. 1 2 3 4 1. DC power jack: Connects to the power cord. 2.
Adjusting the Viewing Angle For optimal viewing, the viewing angle of the monitor may be adjusted 35 degrees up and 3 degrees down.
Operating the Monitor A. The Control Panel AUTO _ + 1 2 3 4 5 6 1. Auto: Automatically fixes, centers and fine-tunes the video signal to eliminate noise and distortion. 2. OSD Menu/select: Displays the OSD menu, and selects a submenu item. 3. Adjustment button —: Indicates cursor movement, or decreases the value of a selected OSD setting. 4. Adjustment button +: Indicates cursor movement, or increases the value of a selected OSD setting. 5. Power switch ( or OFF.
B. Hot Keys 1. Volume adjust hot key —: Decreases the volume. 2. Volume adjust hot key +: Increases the volume. C. Adjusting the Monitor’s Display 1. Pressing the OSD Menu button causes the screen below to appear. 2. Press the + or — button to select a menu item. 3. Press the OSD Menu button again to enter the selected submenu. 4. Press the + or — button to change the value. 5. Select EXIT and press the OSD Menu button when finished adjusting.
The Menu Table Main Menu Submenu Function BRIGHTNESS Adjusts the level of brightness and darkness. CONTRAST Adjusts the RGB color pattern set of the contrast. V-POSITION DISPLAY ADJUST Moves the screen vertically (up/down). H-POSITION Moves the screen horizontally (left/right). PITCH Adjusts image distortion appearing as vertical bars or noise. PHASE Adjusts image distortion appearing as horizontal bars or noise. SHARPNESS Adjusts the LCD monitor display to sharpen the image.
Specifications LCDType 20.1” UXGA Color TFT Display Area 16.06” x 12.05” (408.0 x 306.0 mm) Input Signal Analog, Digital Dot Pitch 0.255 x 0.255 mm Resolution 1600 x 1200 Display Color 16.77 million colors Contrast Ratio 700:1 Brightness 250 nit Response Time 25 ms Display Mode VGA, SVGA, XGA, SXGA, UXGA Viewing Angle (H) 170°/(V) 170° Plug and Play VESA DDC 1/2B Audio 3W x 2 Dimensions (H x W x D) 18.1” x 22.4" x 9.5" (460 x 568 x 240 mm) Gross/Net Weight 24.3/21.6 lbs. (11/9.
Supported Timing Display Mode VGA SVGA XGA SXGA UXGA Macintosh 720 x 350 640 x 480 640 x 480 640 x 480 640 x 480 720 x 400 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1280 x 1024 1280 x 1024 1600 x 1200 1600 x 1200 640 x 480 832 x 624 1024 x 768 1152 x 870 Analog Horizontal Frequency Vertical Frequency (KHz) (Hz) 31.469 70.087 37.469 59.940 35.000 66.667 37.861 72.809 37.500 75.000 31.469 70.087 35.156 56.250 37.879 60.317 48.077 72.188 46.875 75.
Troubleshooting This LCD monitor comes pre-adjusted with standard VGA timing. Due to output timing differences among various VGA cards, you may initially experience an unstable or unclear display when a new display mode or new VGA card is selected. Before applying any of the following troubleshooting procedures, you should first apply the Auto Adjust option in the OSD menu.
