Specifications

ManualsBrandsMicrotek ManualsComputer equipmentArtixScan 4000tf



 2001 by Microtek International, Inc.

Trademarks

Microtek™, Artix™, ScanWizard™ Pro TX, and ArtixScan™ are trademarks of Microtek International, Inc. Macintosh

, Apple

, FireWire

and FireWire logo are trademarks or

registered trademarks of Apple Computer, Inc. Windows

is a registered trademark of Microsoft Corporation. All other products or name brands are trademarks of their respective

holders.

Important

Documents you scan may be protected under copyright law. The unauthorized use of such documents could be a violation of the rights of the copyright holder. Microtek bears no

responsibility for the unauthorized use of copyrighted materials.

May 2001

I49-003042 A

Federal Communications Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not

expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Responsible Party: Loi Han

3715 Doolittle Drive

Redondo Beach, CA 90278-1226

USA

Telephone No: 1-310-297-5000

Federal Communications Commission Interference Statement

This equipment (Model: MTS-4000F) has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Note: 1) A shielded of SCSI interface cable with ferrite core installed on the scanner connector end must be used with this equipment. 2) A shielded of FireWire interface cable with ferrite core

installed on the scanner connector end must be used with this equipment. 3) AC adapter with ferrite core installed on the scanner connector end must be used with this equipment.

Caution

: :

: Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment.

Trade Name Model Number

ArtixScan 4000tf MTS-4000F

Tested to Comply

With FCC Standards

FOR HOME OR OFFICE USE

Microtek Lab, Inc.Microtek Lab, Inc.

Microtek Lab, Inc.

3715 Doolittle Drive

Redondo Beach, CA 90278-1226

USA

Main: +1-310-297-5000

Sales: 800-654-4160

FAX: +1-310-297-5050

BBS: +1-310-297-5102

Technical Support: +1-310-297-5151

AutoTech fax back system: +1-310-297-5101

http://www.microtekusa.com

Microtek International, Inc.Microtek International, Inc.

Microtek International, Inc.

6, Industry East Road 3

Science-Based Industrial Park

Hsinchu 300

Taiwan

TEL: +886-3-5772155

FAX: +886-3-5772598

http://www.microtek.com

MicrMicr

Micr

otek Eurotek Eur

otek Eur

ope B.Vope B.V

ope B.V

Klompenmaker Str. 76

3194DE Hoogvliet-RT

The Netherlands

TEL: +31-10-2425688

FAX: +31-10-2425699

http://www.microtekeurope.com

Artix Japan CorporationArtix Japan Corporation

Artix Japan Corporation

SanKyou Bldg., 2F, 2-6-7 Kitaueno

Taito-ku, Tokyo 110-0014

Japan

TEL: +81-3-5830-1227

FAX: +81-3-5830-1228

http://www.artixjapan.co.jp

Microtek Computers (Asia) Pte. Ltd.Microtek Computers (Asia) Pte. Ltd.

Microtek Computers (Asia) Pte. Ltd.

160, Paya Leber Road

#05-04 Orion Industrial Building

Singapore 409022

TEL: +65-747-7851

FAX: +65-747-7852

http://www.microtek.com.sg

Adara International, Inc.Adara International, Inc.

Adara International, Inc.

8F, No. 220 Ta-Tung Road, Section 3

His-Chih City, Taipei 221, Taiwan

TEL: +886-2-86471488

FAX: +886-2-86471422

http://www.adara.com.tw

Shanghai MicrShanghai Micr

Shanghai Micr

otek Totek T

otek T

echnology Co., Ltd.echnology Co., Ltd.

echnology Co., Ltd.

Building 35, No. 680, Guiping Road

Shanghai 200233, P.R.C.

TEL: +86-21-64856614

FAX: +86-21-64859686

http://www.microtek.com.cn