DR AF T Nokia 6131/6133 User Guide FCC Draft Issue 1
DECLARATION OF CONFORMITY Hereby, NOKIA CORPORATION, declares that this product RM-115 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity can be found from http://www.nokia.com/phones/declaration_of_conformity/. 0434 The crossed-out wheeled bin means that within the European Union the product must be taken to separate collection at the product end-of life.
This Nokia device complies with Directive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment. Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused. The contents of this document are provided "as is".
Contents General information .............. 10 Overview of functions........................ Access codes......................................... Configuration settings service ........ Download content .............................. Nokia support....................................... 10 10 11 12 12 1. Get started ......................... 13 13 14 14 14 15 15 16 16 AF Install SIM card and battery ............ Insert a microSD card ........................ Remove the microSD card ................
My shortcuts......................................... 58 Connectivity.......................................... 59 Call........................................................... 65 Phone ...................................................... 66 Enhancements ...................................... 66 Configuration........................................ 67 Security .................................................. 68 Phone software updates.................... 69 Restore factory settings.....................
DR AF T Contents 6
For your safety For your safety Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information. SWITCH ON SAFELY Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger. ROAD SAFETY COMES FIRST INTERFERENCE T Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety.
For your safety WATER-RESISTANCE Your phone is not water-resistant. Keep it dry. BACK-UP COPIES Remember to make back-up copies or keep a written record of all important information stored in your phone. CONNECTING TO OTHER DEVICES When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products. EMERGENCY CALLS AF ■ About your device T Ensure the phone is switched on and in service.
For your safety device may also have been specially configured for your network provider. This configuration may include changes in menu names, menu order and icons. Contact your service provider for more information. This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols.
General information General information ■ Overview of functions Your phone provides many functions that are practical for daily use, such as a text and multimedia messaging, a calendar, a clock, an alarm clock, a radio, a music player, and a built-in camera. Your phone also supports the following functions: T • Plug and play online service to get the configuration settings. See “Plug and play service,”p. 16, and “Configuration settings service,” p. 11. • Push to talk. See “Push to talk,” p. 84.
General information PIN codes The personal identification number (PIN) code and the universal personal identification number (UPIN) code (4 to 8 digits) help to protect your SIM card against unauthorized use. See “Security,” p. 68. The PIN2 code (4 to 8 digits) may be supplied with the SIM card and is required for some functions. The module PIN is required to access the information in the security module. See “Security module,” p. 100. T The signing PIN is required for the digital signature.
General information To save the settings, select Show > Save. If the phone requests Enter settings' PIN:, enter the PIN code for the settings, and select OK. To receive the PIN code, contact the service provider that supplies the settings. If no settings are saved yet, these settings are saved and set as default configuration settings. Otherwise, the phone asks Activate saved configuration settings?. To discard the received settings, select Exit or Show > Discard.
Get started 1. Get started ■ Install SIM card and battery Always switch the device off and disconnect the charger before removing the battery. Keep all SIM cards out of the reach of small children. For availability and information on using SIM card services, contact your SIM card vendor. This may be the service provider, network operator, or other vendor. T This device is intended for use with BL-4C battery. Always use original Nokia batteries. See “Nokia battery authentication,” p. 104.
Get started ■ Insert a microSD card Keep all microSD memory cards out of the reach of small children. 1. Remove the back cover of the phone. 2. Insert the card into the microSD card slot with the golden contact surface facing down, and press it until it locks into place. 3. Close the back cover of the phone. AF T Use only compatible microSD cards with this device. Other memory cards, such as Reduced Size MultiMedia cards, do not fit in the microSD card slot and are not compatible with this device.
Get started Warning: Use only batteries, chargers, and enhancements approved by Nokia for use with this particular model. The use of any other types may invalidate any approval or warranty, and may be dangerous. For availability of approved enhancements, please check with your dealer. When you disconnect the power cord of any enhancement, grasp and pull the plug, not the cord. 1. Connect the charger to a wall socket. 2. Connect the lead from the charger to the socket on the bottom of your phone.
Get started Set the time, time zone, and date Enter the local time, select the time zone of your location in terms of the time difference with respect to Greenwich Mean Time (GMT), and enter the date. See “Time and date,” p. 57. Plug and play service AF ■ Antenna T When you switch on your phone for the first time, and the phone is in the standby mode, you are asked to get the configuration settings from your service provider (network service). Confirm or decline the query. See "Connect to serv.
Your phone 2. Your phone ■ Keys and parts 1 Earpiece 2 Main display 3 Left and right selection keys 4 Middle selection key 6 Keypad 7 Infrared window AF 8 Fold release button T 5 Call key 9 4-way navigation key 10 End key 11 Loudspeaker 12 Phone strap eyelet DR 13 Pop-PortTM connector flap 14 Charger connector 15 Camera lens 16 Volume keys (Volume up = PTT key) 17 Mini display 18 Camera key 19 Power key Connector flap To connect enhancements, open the Pop-PortTM connector flap.
Your phone ■ Standby mode When the phone is ready for use, and you have not entered any characters, the phone is in the standby mode. Main display 1 Signal strength of the cellular network 2 Battery charge status 3 Indicators 4 Name of the network or the operator logo T 5 Clock 6 Main screen AF 7 Function of the left selection key is Go to or a shortcut to another function. See “Left selection key,”p. 58.
Your phone To organize and change the active standby mode, activate the navigation mode, and select Options > Active standby > My active standby > Options and the following options: Personalise — Assign or change phone features in the standby mode. Organise — Move the position of features in the standby mode. Enabling active standby — Select keys to activate the standby navigation mode. To change the settings, see “Standby mode settings,” p. 56.
Your phone Your phone is connected to the instant messaging service, and the availability status is online or offline. , You received one or several instant messages, and you are connected to the instant messaging service. The keypad is locked. The phone does not ring for an incoming call or text message. The alarm clock is set to On. The countdown timer is running. T The stopwatch is running in the background. The phone is registered to the GPRS or EGPRS network.
Your phone ■ Keypad lock (keyguard) To prevent the keys from being accidentally pressed, select Menu, and press within 3.5 seconds to lock the keypad. * To unlock the keypad, select Unlock, and press within 1.5 seconds. If the Security keyguard is set On, enter the security code if requested. * To answer a call when the keyguard is on, press the call key. When you end or reject the call, the keypad automatically locks. For Security keyguard, see “Phone,” p. 66.
Call functions 3. Call functions ■ Make a call 1. Enter the phone number, including the area code. For international calls, press twice for the international prefix (the + character replaces the international access code), enter the country code, the area code without the leading 0, if necessary, and the phone number. * T 2. To call the number, press the call key. 3. To end the call or to cancel the call attempt, press the end key, or close the phone.
Call functions Voice commands are language-dependent. To set the language, see Voice playback language in “Phone,” p. 66. Note: Using voice tags may be difficult in a noisy environment or during an emergency, so you should not rely solely upon voice dialing in all circumstances. 1. In the standby mode, press and hold the right selection key or press and hold the volume down key. A short tone is played, and Speak now is displayed.
Call functions Call waiting To answer the waiting call during an active call, press the call key. The first call is put on hold. To end the active call, press the end key. To activate the Call waiting function, see “Call,” p. 65. ■ Options during a call Many of the options that you can use during a call are network services. For availability, contact your service provider.
Write text 4. Write text T You can enter text (for example, when writing messages) using traditional or predictive text input. When you write text, text input indicators appear at the top of the display. indicates traditional text input. indicates predictive text input. Predictive text input allows you to write text quickly using the phone keypad and a built-in dictionary. You can enter a letter with a single keypress. indicates predictive text input with Word suggestions.
Write text If the word is not correct, press repeatedly, or select Options > Matches. When the word that you want appears, select the word and press the navigation key. * If the ? character is displayed after the word, the word you intended to write is not in the dictionary. To add the word to the dictionary, select Spell. Complete the word (traditional text input is used), and select Save. ■ Traditional text input To set traditional text input on, select Options > Prediction off.
Navigate the menus 5. Navigate the menus The phone offers you an extensive range of functions, which are grouped into menus. 1. To access the menu, select Menu. To change the menu view, select Options > Main menu view > List, Grid, Grid with labels, or Tab. T To rearrange the menu, scroll to the menu you want to move, and select Options > Organise > Move. Scroll to where you want to move the menu, and select OK. To save the change, select Done > Yes. AF 2.
Messaging 6. Messaging You can read, write, send, and save text, multimedia, e-mail, audio, and flash messages and postcards. All messages are organized into folders. ■ Text messages (SMS) With the short message service (SMS) you can send and receive text messages, and receive messages that can contain pictures (network service). T Before you can send any text or SMS e-mail message, you must save your message center number. See “Message settings,” p. 44.
Messaging used. To retrieve contacts from previously incoming calls, select Add > Open Log. 3. For a SMS e-mail, enter a subject in the Subject: field. 4. Write your message in the Message: field. See “Write text,” p. 25. To insert a template into the message, select Options > Use template. To see how the message will look to the recipient, select Options > Preview. 5. To send the message, select Send. See “Message sending,” p. 31.
Messaging ■ Multimedia messages (MMS) Note: Only devices that have compatible features can receive and display multimedia messages. The appearance of a message may vary depending on the receiving device. To check availability and to subscribe to the multimedia messaging network service, contact your service provider. See “Multimedia messages,” p. 45. T A multimedia message can contain text, sound, images, video clips, a business card, and a calendar note.
Messaging message to multiple recipients, add the desired contacts one by one. To send the message to persons in a group, select Contact group and the desired group. To retrieve the contacts to which you recently sent messages, select Add > Recently used. Message sending Copyright protections may prevent some images, music (including ringing tones), and other content from being copied, modified, transferred or forwarded. T When you finish writing your message, to send the message, select Send.
Messaging 1. To read the message, select Show. To view it later, select Exit. To read the message later, select Menu > Messaging > Inbox. Scroll to the message that you want to view, and select it. is shown if you have unread messages in Inbox. 2. To view the whole message if the received message contains a presentation, select Play. To view the files in the presentation or the attachments, select Options > Objects or Attachments. T 3.
Messaging You can move your messages to the Saved items folder. To organize your Saved items subfolders, select Menu > Messaging > Saved items. To add a folder, select Options > Add folder. To delete or rename a folder, scroll to the desired folder, and select Options > Delete folder or Rename folder. Your phone has templates. To create a new template, save a message as a template. To access the template list, select Menu > Messaging > Saved items > Templates.
Messaging ■ Flash messages Flash messages are text messages that are instantly displayed upon reception. Flash messages are not automatically saved. Write a flash message Receive a flash message T Select Menu > Messaging > Create message > Flash message. Enter the recipient’s phone number in the To: field. Scroll down, and write your message in the Message: field. The maximum length of a flash message is 70 characters.
Messaging Receive an audio message When your phone receives an audio message, 1 audio message received is displayed. To open the message, select Play; or if more than one message is received, select Show > Play. To listen to the message later, select Exit. To see the available options, select Options. ■ E-mail application T The e-mail application uses a packet data connection (network service) to allow you to access your e-mail account from your phone when you are not in the office or at home.
Messaging The Manage accounts options allow you to add, delete, and change the e-mail settings. Make sure that you have defined the correct preferred access point for your operator. See “Configuration,” p. 67. The e-mail application requires an Internet access point without a proxy. WAP access points normally include a proxy and do not work with the e-mail application.
Messaging 2. Select Back. 3. Select Inboxes, the account name, and the new message, and select Retrieve to download the complete e-mail message. To download new e-mail messages and to send e-mail that has been saved in the Outbox folder, select Options > Send and check for e-mail Read and reply to e-mail Important: Exercise caution when opening messages. E-mail messages may contain malicious software or otherwise be harmful to your device or PC. T 1.
Messaging the main e-mail idle screen. The spam filter allows the user to put specific senders on a black or white list. Black list sender messages are filtered to the Junk folder. Unknown and White list sender messages are downloaded into the account inbox. To blacklist a sender, select the email message in the Inboxes folder and Options > Blacklist sender.
Messaging will have the opportunity to create the user name and password of your choice. For more information about signing up for instant messaging services, contact your wireless service provider. Access The following options are shown: T To access the Instant messages menu while still offline, select Menu > Messaging > Instant messages (Instant messages may be replaced by another term depending on the service provider).
Messaging Sessions When connected to the instant messaging service your status as seen by others is shown in a status line: My status: Online, My status: Busy or Status: Appear offline — to change own status, select Change. Below the status line there are three folders containing your contacts and showing their status: Conversations, Online and Offline. To expand the folder highlight it and select Expand (or press scroll right), to collapse the folder select Collapse (or press scroll left).
Messaging Search > Users or Groups — to search for other instant messaging users or public groups on the network by phone number, screen name, e-mail address, or name. If you select Groups, you can search for a group by a member in the group, or by group name, topic, or ID. Options > Chat or Join group — to start the conversation when you have found the user or the group that you want.
Messaging Write your message; and select Send, or press the call key. Your message is displayed, and the reply message is displayed below your message. Add IM contacts When connected to the IM service, in the IM main menu select Options > Add contact. Select By mobile number, Enter ID manually, Search from server, or Copy from server (depending on service provider). When the contact is successfully added, the phone confirms it. Block or unblock messages T Scroll to a contact.
Messaging group. To delete a group from your group list, select Options > Delete group. To search for a group, select Groups > Public groups > Search groups. You can search for a group by a member in the group, by group name, topic, or ID. Private ■ Voice messages T Connect to the IM service, and from the main menu select Options > Create group. Enter the name for the group and the screen name that you want to use as your nickname.
Messaging ■ Delete messages To delete messages, select Menu > Messaging > Delete messages > By message to delete single messages, By folder to delete all messages from a folder, or All messages. If a folder contains unread messages, the phone asks whether you want to delete them also. ■ Message settings General settings T General settings are common for text and multimedia messages.
Messaging E-mail message centres > Add centre — to set the phone numbers and name of the e-mail center for sending SMS e-mails.
Messaging setting of the multimedia message service is generally In home network. The availability of this menu depends on your phone. Incoming multim. msgs. — to allow the reception of multimedia messages automatically, manually after being prompted, or to reject the reception. This setting is not shown if Allow multimedia recept. is set to No. Allow adverts — to receive or reject advertisements. This setting is not shown if Allow multimedia recept. is set to No, or Incoming multim. msgs.
Messaging SMTP password — to enter the password that you want to use for outgoing mail Display terminal window > Yes — to perform manual user authentication for intranet connections Incoming server type > POP3 or IMAP4 — to select the type of e-mail system that you are using.
Contacts 7. Contacts You can save names and phone numbers (contacts) in the phone memory and in the SIM card memory. The phone memory may save contacts with additional details, such as various phone numbers and text items. You can also save an image for a limited number of contacts. AF ■ Search for a contact T The SIM card memory can save names with one phone number attached to them. The contacts saved in the SIM card memory are indicated by . Select Menu > Contacts > Names.
Contacts 2. Search for the contact to which you want to add a detail, and select Details > Options > Add detail. Select from the options available. To search for an ID from the server of your service provider if you have connected to the presence service, select User ID > Search. See “My presence,” p. 50. If only one ID is found, it is automatically saved. Otherwise, to save the ID, select Options > Save. To enter the ID, select Enter ID manually. Enter the ID, and select OK to save it.
Contacts contacts > From phone memory or From SIM card. Confirm with the security code. To delete a contact, search for the desired contact, and select Options > Delete contact. To delete a number, text item, or an image attached to the contact, search for the contact, and select Details. Scroll to the desired detail, and select Options > Delete and from the options available. Deleting an image or video clip from contacts does not delete it from Gallery.
Contacts Edit my presence > My availability, My presence message, My presence logo, or Show to — to change your presence status My viewers > Current viewers, Private list, or Blocked list — to view the persons who are subscribed to or blocked from your presence information Settings > Show pres. in standby, Connection type, or Presence settings ■ Subscribed names T You can create a list of contacts whose presence status information you want to be aware of.
Contacts View the subscribed names To view the presence information, see also “Search for a contact,” p. 48. 1. Select Menu > Contacts > Subscribed names. The status information of the first contact on the subscribed names list is displayed. The information that the person wants to make available to others may include text and an icon. , , or indicates that the person is available, not visible to others, or not available. indicates that the person’s presence information is not available. AF T 2.
Contacts memories. In that case, when you save names and numbers, they are saved in the phone memory.
Call log 8. Call log The phone registers your missed, received, and dialed calls if the network supports it and the phone is switched on and within the network service area. T To view the information on your calls, select Menu > Log > Missed calls, Received calls, or Dialled numbers. To view your recent missed and received calls and the dialed numbers chronologically, select Call log. To view the contacts to whom you most recently sent messages, select Message recipients.
Settings 9. Settings ■ Profiles Your phone has various setting groups called profiles, for which you can customize the phone tones for different events and environments. Select Menu > Settings > Profiles, the desired profile and from the following options: Activate — to activate the selected profile T Personalise — to personalize the profile. Select the setting you want to change, and make the changes. AF Timed — to set the profile to be active until a certain time up to 24 hours, and set the end time.
Settings If you select the highest ringing tone level, the ringing tone reaches its highest level after a few seconds. A theme may contain a tone that sounds when you open and close the phone. To switch off the tone, change the setting in Other tones:. Please note that this setting also switches off the warning tones. ■ Main display Select Menu > Settings > Main display and from the available options.
Settings Screen savers > Image — to choose an image or a graphic from the Gallery Screen savers > Slide set and a folder in the Gallery — to use the images in the folder as a slide set Screen savers > Video clip and a video clip from the Gallery — to run a video clip as screensaver (only on the main display) Screen savers > Open camera — to take a new photo as screensaver Screen savers > Analogue clock or Digital clock — to use a clock as screensaver T Graphic downloads — to download more images for the
Settings ■ My shortcuts With personal shortcuts you get quick access to often used functions of the phone. Left selection key To select a function from the list for the left selection key, select Menu > Settings > My shortcuts > Left selection key. See also “Standby mode,” p. 18. T If the left selection key is Go to to activate a function, in the standby mode, select Go to > Options and from the following options: Select options — to add a function to the shortcut list or to remove one.
Settings Navigation key To select shortcut functions for the navigation keys, select Menu > Settings > My shortcuts > Navigation key. Scroll to the desired key, and select Change and a function from the list. To remove a shortcut function from the key, select (empty). To reassign a function for the key, select Assign. See “Shortcuts in the standby mode,” p. 19. Voice commands T To call contacts and carry out phone functions, say the voice commands. Voice commands are language-dependent.
Settings use Nokia approved enhancements for this model. Check with the manufacturers of other devices to determine their compatibility with this device. There may be restrictions on using Bluetooth technology in some locations. Check with your local authorities or service provider. Features using Bluetooth technology or allowing such features to run in the background while using other features, increase the demand on battery power and reduce the battery life.
Settings Bluetooth settings To define how your phone is shown to other Bluetooth devices, select Menu > Settings > Connectivity > Bluetooth > Bluetooth settings > My phone's visibility or My phone's name. If you are concerned about security, turn off the Bluetooth function, or set My phone's visibility to Hidden. Always accept only Bluetooth communication from others with whom you agree. Infrared AF T You can set up the phone to send and receive data through its infrared (IR) port.
Settings Packet data (GPRS) General packet radio service (GPRS) is a network service that allows mobile phones to send and receive data over an Internet protocol (IP)-based network. It enables wireless access to data networks such as the Internet. The applications that may use packet data are MMS, video streaming, browsing sessions, e-mail, Push to talk, remote SyncML, Java application downloading, and the PC dial-up.
Settings Data transfer Synchronize your calendar, contacts data, and notes with another compatible device (for example, a mobile phone), a compatible PC, or a remote Internet server (network service). Your phone allows data transfer with a compatible PC or another compatible device when using the phone without a SIM card. Note that when you use the phone without a SIM card, some functions appear dimmed in the menus and cannot be used.
Settings synchronisation or PC synchronisation. According to the settings, the selected data is copied or synchronized. The other device also must be activated for receiving data. Synchronize from a compatible PC Before you synchronize data from calendar, notes, and contacts from a compatible PC, you must install the Nokia PC Suite software of your phone on the PC. Use Bluetooth wireless technology or a USB data cable for the synchronization, and start the synchronization from the PC.
Settings To change the USB mode, select Menu > Settings > Connectivity > USB data cable > Default mode, Printing, or Data storage. ■ Call Select Menu > Settings > Call and from the following options: Call divert — to divert your incoming calls (network service). You may not be able to divert your calls if some call barring functions are active. See Call barring service in “Security,” p. 68.
Settings ■ Phone Select Menu > Settings > Phone and from the following options: Language settings — to set the display language of your phone, select Phone language. If you select Automatic, the phone selects the language according to the information on the SIM card. To select the USIM card language, select SIM language. To set a language for the voice playback, select Voice playback language. See “Enhanced voice dialing,” p. 22 and Voice commands in “My shortcuts,” p. 58.
Settings Select Menu > Settings > Enhancements. Select an enhancement, and depending on the enhancement, from the following options: Default profile — to select the profile that you want to be automatically activated when you connect to the selected enhancement Automatic answer — to set the phone to answer an incoming call automatically after 5 seconds. If Incoming call alert is set to Beep once or Off, automatic answer is off. Lights — to set the lights permanently On.
Settings Preferred access point — to view the saved access points. Scroll to an access point, and select Options > Details to view the name of the service provider, data bearer, and packet data access point or GSM dial-up number. Connect to serv. support — to download the configuration settings from your service provider Device manager settings — to allow or prevent the phone from receiving phone software updates. This option may not be available, depending on your phone. See “Phone software updates,” p.
Settings AF T Security level > Phone — to set the phone to ask for the security code whenever a new SIM card is inserted into the phone. If you select Memory, the phone asks for the security code when the SIM card memory is selected, and you want to change the memory in use.
Operator menu Depending on your settings you will be notified that a software update is available for download or has been downloaded and installed automatically. Request a software update Install a software update T Select Menu > Settings > Phone > Phone updates to request available phone software updates from your service provider. Select Current software details to display the current software version and check whether an update is needed. Select Download phone softw.
Gallery 11. Gallery In this menu you can manage images, video clips, music files, themes, graphics, tones, recordings, and received files. These files are stored in the phone memory or a attached microSD memory card and may be arranged in folders. Your phone supports an activation key system to protect acquired content. Always check the delivery terms of any content and activation key before acquiring them, as they may be subject to a fee.
Gallery card see “Insert a microSD card,” p. 14 and “Remove the microSD card,” p. 14. The following options may can also be accessed from the Gallery. Format the memory card When a memory card is formatted, all data on the card is permanently lost. Some memory cards are supplied preformatted and others require formatting. Consult your retailer to find out if you must format the memory card before you can use it. 1. Select Menu > Applications and the memory card folder . 3. Select Yes to confirm. T 2.
Media 12. Media When taking and using images or video clips, obey all laws and respect local customs as well as privacy and legitimate rights of others. ■ Camera You can take photos or record video clips with the built-in camera. Take a photo T To start the camera, press the camera key in the standby mode, or select Menu > Media > Camera. DR AF To take an image in landscape format, hold the phone in a horizontal position.
Media Record a video clip To select the video mode, scroll left or right, or select Options > Video. To start the video recording, select Record. To pause the recording, select Pause; to resume the recording, select Continue. To stop the recording, select Stop. The phone saves the recording in Gallery > Video clips. Camera options To use a filter with the camera, select Options > Effects >False colours, Greyscale, Sepia, Negative, or Solarise.
Media ■ Music player Your phone includes a music player for listening to music tracks, recordings or other MP3 or AAC sound files that you have transferred to the phone with the Nokia Audio Manager application, which is part of Nokia PC Suite. See “Nokia PC Suite,” p. 102. Music files stored in a folder in the phone memory or in a folder of the multimedia card, will automatically be detected and added to the default track list.
Media Play options — Select Random to play the tracks on the track list in random order. Select Repeat to play the current track or the entire track list repeatedly. Select Music source to select a folder with music tracks. Media equaliser — Select or define an equalizer setting. See “Equalizer,” p. 78. Loudspeaker/Headset— Listen to the music player using the phone loudspeaker or headset. (Only if a headset is attached) Tip: When using a headset, press the headset key to skip to the next track.
Media from 10 to 20, press briefly 1 or 2, and press and hold the desired number key, 0 to 9. 3. Enter the name of the radio station. Listen to the radio Select Menu > Media > Radio. To scroll to the desired frequency, select or , or press the headset key. To select a radio station, briefly press the corresponding number keys. To adjust the volume, press the volume keys.
Media When an application using a packet data or HSCSD connection is sending or receiving data, it may interfere with the radio. ■ Voice recorder You can record pieces of speech, sound, or an active call, and save them in Gallery. This is useful when recording a name and phone number to write down later. The recorder cannot be used when a data call or GPRS connection is active. Record sound T 1. Select Menu > Media > Voice recorder.
Media ■ Stereo widening DR AF T Stereo widening enhances the audio output of the music player by enabling a wider stereo sound effect. To change the setting, select Menu > Media > Stereo widening.
Organizer 13. Organizer ■ Alarm clock You can set the phone to alarm at a desired time. Select Menu > Organiser > Alarm clock. To set the alarm, select Alarm time, and enter the alarm time. To change the alarm time when the alarm time is set, select On. T To set the phone to alert you on selected days of the week, select Repeat alarm. AF To select the alarm tone or set the radio as the alarm tone, select Alarm tone. If you select the radio as an alarm tone, connect the headset to the phone.
Organizer below the calendar. To view the day notes, select View. To view a week, select Options > Week view. To delete all notes in the calendar, select the month or week view, and select Options > Delete all notes. Make a calendar note T Other options for the day view may be to make a note; delete, edit, move, or repeat a note; copy a note to another day; send a note with Bluetooth technology; or send a note to the calendar of another compatible phone as a text message or multimedia message.
Organizer You can sort the notes by priority or by deadline, send a note to another phone as a text message or a multimedia message, save a note as a calendar note, or access the calendar. ■ Notes To write and send notes, select Menu > Organiser > Notes. To make a note if no note is added, select Add; otherwise, select Options > Make a note. Write the note, and select Save. AF ■ Calculator T Other options include deleting and editing a note.
Organizer ■ Countdown timer Select Menu > Organiser > Countdown timer. Enter the alarm time in hours, minutes, and seconds, and select OK. If you wish, write your own note text that is displayed when the time expires. To start the countdown timer, select Start. To change the countdown time, select Change time. To stop the timer, select Stop timer.
Push to talk 14. Push to talk Select Menu > Push to talk. Push to talk (PTT) over cellular is a two-way radio service available over a GPRS cellular network (network service). You can use PTT to have a conversation with one person or with a group of people (channel) having compatible devices. While you are connected to the PTT service, you can use the other functions of the phone. T To check availability and costs, and to subscribe to the service, contact your network operator.
Push to talk Create a channel To add a channel, select Menu > Push to talk > Add channel and enter the settings in the form fields: Channel name: — Enter a name for the new channel. Channel status: — Select Active to set the channel active, or Inactive to disable the channel. Nickname in channel: — Enter your nick name to be shown the new channel.
Push to talk ■ Switch PTT on and off To connect to the PTT service, select Menu > Push to talk > Switch PTT on, or press and hold the PTT (volume up) key. indicates the PTT connection. indicates that the service is temporarily unavailable. If you have added channels to the phone, you are automatically joined to the active channels. You may assign a default function to the PTT (volume up) key to open the channel list, the contacts list or a single channel or contact. See “PTT settings,” p. 89.
Push to talk Make a one-to-one call To start a one-to-one call from the list of contacts to which you have added the PTT address, select Contacts > Names or Menu > Push to talk > Contacts list. Scroll to a contact, and press and hold the PTT (volume up) key. To start a one-to-one call from the list of PTT channels, select Channel list, scroll to the desired channel, and select Members. Scroll to the desired contact, and press and hold the PTT (volume up) key.
Push to talk When you press and hold the PTT (volume up) key while the caller is talking, you hear a queuing tone, and Queuing is displayed. Press and hold the PTT (volume up) key, and wait for the other person to finish; then you can talk immediately. ■ Callback requests If you make a one-to-one call and do not get a response, you can send a request for the person to call you back.
Push to talk To delete the request, select Delete. To save a new contact or to add the PTT address to a contact from a received callback request, select Options > Save as or Add to contact. ■ Add a one-to-one contact You can save the names of persons to whom you often make one-to-one calls in the following ways: T To add a PTT address to a name in Contacts, search for the desired contact, select Details > Options > Add detail > Push to talk address.
Push to talk PTT status in startup > Yes or Ask first— to set the phone to automatically connect to the PTT service when you switch the phone on Push to talk when abroad — to switch the PTT service on or off when the phone is used outside of the home network Send my PTT address > No — to hide your PTT address from channel and one-to-one calls ■ Configuration settings T You may receive the settings for connecting to the service from your service provider. See “Configuration settings service,” p. 11.
Applications 15. Applications In this menu you can manage applications and games. These files are stored in the phone memory or a attached microSD memory card and may be arranged in folders. For options to format or lock and unlock the memory card see “Memory card,” p. 71. ■ Launch a game T Your phone software includes some games. AF Select Menu > Applications > Games. Scroll to the desired game, and select Open.
Applications Web page — to provide further information or additional data for the application from an Internet page (network service). It is only shown if an Internet address has been provided with the application. ■ Download an application Your phone supports J2ME Java applications. Make sure that the application is compatible with your phone before downloading it.
Applications 2. Launch and configure the PC component. Make sure that the selected incoming Bluetooth serial port (COM port) corresponds to the one defined in the Bluetooth software settings on the Bluetooth device of your PC. For details, refer to the PC component documentation and “Set up a Bluetooth connection,” p. 60. 3. Open the slide presentation, or start the application you want to control remotely from your phone.
SIM services 16. SIM services Your SIM card may provide additional services. You can access this menu only if it is supported by your SIM card. The name and contents of the menu depend on the available services. For availability and information on using SIM card services, contact your SIM card vendor. This may be the service provider, network operator, or other vendor.
Web 17. Web You can access various mobile Internet services with your phone browser. Important: Use only services that you trust and that offer adequate security and protection against harmful software. Check the availability of these services, pricing, tariffs, and instructions with your service provider. AF T With the phone browser you can view the services that use wireless markup language (WML) or extensible hypertext markup language (XHTML) on their pages. Appearance may vary due to screen size.
Web Make a connection to the service in one of the following ways: • Select Menu > Web > Home; or in the standby mode, press and hold 0. • To select a bookmark of the service, select Menu > Web > Bookmarks. • To select the last URL, select Menu > Web > Last web address. • To enter the address of the service, select Menu > Web > Go to address. Enter the address of the service, and select OK. T ■ Browse pages AF After you make a connection to the service, you can start browsing its pages.
Web Other options — to show a list of other options Reload — to reload and update the current page The service provider may also offer other options. Direct calling While browsing, you can make a phone call, and save a name and a phone number from a page. ■ Bookmarks T You can save page addresses as bookmarks in the phone memory. AF 1. While browsing, select Options > Bookmarks; or in the standby mode, select Menu > Web > Bookmarks. 2.
Web Show images > No — to hide images on the page. This can speed up the browsing of pages that contain a lot of images. Alerts > Alert for unsecure conn. > Yes — to set the phone to alert when a secure connection changes to an unsecure one during browsing Alerts > Alert for unsecure items > Yes — to set the phone to alert when a secure page contains an unsecure item. These alerts do not guarantee a secure connection. For more information, see “Browser security,” p. 100.
Web ■ Download settings To automatically save all downloaded files in Gallery, select Menu > Web > Settings > Downloading settings > Automatic saving > On. ■ Service inbox The phone is able to receive service messages sent by your service provider (network service). Service messages are notifications (for example, news headlines), and they may contain a text message or an address of a service. AF T To access the Service inbox in the standby mode, when you have received a service message, select Show.
Web ■ Cache memory A cache is a memory location that is used to store data temporarily. If you have tried to access or have accessed confidential information requiring passwords, empty the cache after each use. The information or services you have accessed is stored in the cache. To empty the cache while browsing, select Options > Other options > Clear the cache; in the standby mode, select Menu > Web > Clear the cache.
Web the owner of the certificate and that the certificate really belongs to the listed owner. There are three kinds of certificates: server certificates, authority certificates, and user certificates. You may receive these certificates from your service provider. Authority certificates and user certificates may also be saved in the security module by the service provider.
PC connectivity 18. PC connectivity You can send and receive e-mail, and access the Internet when your phone is connected to a compatible PC through a Bluetooth or a data cable connection. You can use your phone with a variety of PC connectivity and data communications applications. ■ Nokia PC Suite AF T With Nokia PC Suite you can synchronize contacts, calendar, notes, and to-do notes between your phone and the compatible PC or a remote Internet server (network service).
Battery information 19. Battery information ■ Charging and discharging Your device is powered by a rechargeable battery. The full performance of a new battery is achieved only after two or three complete charge and discharge cycles. The battery can be charged and discharged hundreds of times, but it will eventually wear out. When the talk and standby times are noticeably shorter than normal, replace the battery.
Battery information ■ Nokia battery authentication Always use original Nokia batteries for your safety. To check that you are getting an original Nokia battery, purchase it from an authorized Nokia dealer, look for the Nokia Original Enhancements logo on the packaging, and inspect the hologram label using the following steps: Authenticate hologram T Successful completion of the four steps is not a total assurance of the authenticity of the battery.
Battery information 4. Confirm that the 20-digit code is valid by following the instructions at www.nokia.com/batterycheck. To create a text message enter the 20-digit code, for example, 12345678919876543210, and send to +44 7786 200276. To create a text message, T • For countries in Asia Pacific, excluding India: Enter the 20-digit code, for example, 12345678919876543210, and send to +61 427151515.
Technical Information 20. Technical Information Weight 110 grams (3.1 ounces) incl. BL-4C battery Battery 820 mAh Li-Ion Battery Networks Wireless networks GSM 850, 900, 1800 and 1900 Size Volume: Length: Width: Thickness: AF T 4.45 cubic inches (75 ccm) 3.6 in (92 mm) 1.9 in (48 mm) 0.
Care and maintenance Care and maintenance Your device is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you protect your warranty coverage. • Keep the device dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, remove the battery and allow the device to dry completely before replacing it.
Additional safety information Additional safety information Your device and its enhancements may contain small parts. Keep them out of the reach of small children. ■ Operating environment AF T Remember to follow any special regulations in force in any area, and always switch off your device when its use is prohibited or when it may cause interference or danger. Use the device only in its normal operating positions.
Additional safety information • Always keep the device more than 15.3 centimeters (6 inches) from the pacemaker • Not carry the device in a breast pocket • Hold the device to the ear opposite the pacemaker to minimize the potential for interference. If you suspect interference, switch off your device, and move the device away. Hearing aids Some digital wireless devices may interfere with some hearing aids. If interference occurs, consult your service provider.
Additional safety information depots, storage, and distribution areas; chemical plants; or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often but not always clearly marked. They include below deck on boats, chemical transfer or storage facilities, vehicles using liquefied petroleum gas (such as propane or butane), and areas where the air contains chemicals or particles such as grain, dust, or metal powders.
Additional safety information T guidelines include a substantial safety margin designed to assure the safety of the public, regardless of age and health and to account for any variations in measurements. The exposure guidelines for mobile devices employ a unit of measurement known as the Specific Absorption Rate or SAR. The SAR limit stated in the international guidelines is 2.0 watts/kilogram (W/kg) averaged over 10 grams of tissue.
APPENDIX APPENDIX ■ A message from the CTIA © 2001 Cellular Telecommunications & Internet Association. All Rights Reserved. 1250 Connecticut Avenue, NW Suite 800, Washington, DC 20036. Phone: (202) 785-0081 Safety is the most important call you will ever make. A Guide to Safe and Responsible Wireless Phone Use AF T Tens of millions of people in the U.S. today take advantage of the unique combination of convenience, safety and value delivered by the wireless telephone.
APPENDIX When it comes to the use of wireless phones, safety is your most important call. Wireless phone "Safety Tips" 1. Get to know your wireless phone and its features such as speed dial and redial. Carefully read your instruction manual and learn to take advantage of valuable features most phones offer, including automatic redial and memory. Also, work to memorize the phone keypad so you can use the speed dial function without taking your attention off the road. AF T 2.
APPENDIX times you may be stopped at a stop sign, red light or otherwise stationary. But if you need to dial while driving, follow this simple tip--dial only a few numbers, check the road and your mirrors, then continue. 7. Do not engage in stressful or emotional conversations that may be distracting. Stressful or emotional conversations and driving do not mix--they are distracting and even dangerous when you are behind the wheel of a car.
APPENDIX stolen, call roadside assistance or other special non-emergency wireless number. Careless, distracted individuals and people driving irresponsibly represent a hazard to everyone on the road. Since 1984, the Cellular Telecommunications Industry Association and the wireless industry have conducted educational outreach to inform wireless phone users of their responsibilities as safe drivers and good citizens.
APPENDIX What is FDA's role concerning the safety of wireless phones? Under the law, FDA does not review the safety of radiation-emitting consumer products such as wireless phones before they can be sold, as it does with new drugs or medical devices. However, the agency has authority to take action if wireless phones are shown to emit radiofrequency energy (RF) at a level that is hazardous to the user.
APPENDIX exposure. FCC relies on FDA and other health agencies for safety questions about wireless phones. FCC also regulates the base stations that the wireless phone networks rely upon. While these base stations operate at higher power than do the wireless phones themselves, the RF exposures that people get from these base stations are typically thousands of times lower than those they can get from wireless phones.
APPENDIX key factor in how much exposure a person receives, reducing the amount of time spent using a wireless phone will reduce RF exposure. If you must conduct extended conversations by wireless phone every day, you could place more distance between your body and the source of the RF, since the exposure level drops off dramatically with distance.
APPENDIX then that part of the body will absorb more RF energy. Wireless phones marketed in the U.S. are required to meet safety requirements regardless of whether they are used against the head or against the body. Either configuration should result in compliance with the safety limit.
APPENDIX the phone. This difference between the RF test measurement and actual RF emission is because test measurements are limited by instrument accuracy, because test measurement and actual use environments are different, and other variable factors. This inherent variability is known as “measurement uncertainty.” When FCC conducts post-grant testing of a cell phone, FCC takes into account any measurement uncertainty to determine whether regulatory action is appropriate.
Index Index A options . . . . . . . . . . . . . . . . . . . . 24 settings . . . . . . . . . . . . . . . . . . . 65 waiting . . . . . . . . . . . . . . . . . . . . 24 call log . . . . . . . . . . . . . . . . . . . . . . . 54 call register. See call log. callback request . . . . . . . . . . . . . . . 88 calls answer . . . . . . . . . . . . . . . . . . . . 23 international . . . . . . . . . . . . . . . 22 making of . . . . . . . . . . . . . . . . . . 22 reject . . . . . . . . . . . . . . . . . . . . .
Index hearing aid . . . . . . . . . . . . . . . 67, 109 high-speed circuit switched data 102 HSCSD. See high-speed circuit switched data. D I data communication . . . . . . . . . . . 102 transfer . . . . . . . . . . . . . . . . . . . .63 data cable . . . . . . . . . . . . . . . . . . . . .64 date settings . . . . . . . . . . . . . . . . . .57 delete messages . . . . . . . . . . . . . . . . . .44 digital signature . . . . . . . . . . . . . . 101 display . . . . . . . . . . . . . . . . . . . .
Index numbers . . . . . . . . . . . . . . . . . . . . . . 53 O offline mode . . . . . . . . . . . . . . . . . . 21 one-to-one contact . . . . . . . . . . . . 89 operator menu . . . . . . . . . . . . . . . . . 70 organizer . . . . . . . . . . . . . . . . . . . . . 80 overview functions . . . . . . . . . . . . . 10 P pacemakers . . . . . . . . . . . . . . . . . . 108 packet data . . . . . . . . . . . . . . .62, 102 parts . . . . . . . . . . . . . . . . . . . . . . . . . 17 PC connectivity . . . . . . . . .
Index R S AF radio . . . . . . . . . . . . . . . . . . . . . . . . .76 record sound . . . . . . . . . . . . . . . . . .78 recorder . . . . . . . . . . . . . . . . . . . . . .78 repair service . . . . . . . . . . . . . . . . . .12 ringing tones . . . . . . . . . . . . . . . . . .55 DR safety additional information . . . . . 108 emergency calls . . . . . . . . . . . 110 explosive environments . . . . . 109 guidelines . . . . . . . . . . . . . . . . . . .7 hearing aid . . . . . . . . . . . . . . .
Index switch on and off . . . . . . . . . . . . . . 15 swivel . . . . . . . . . . . . . . . . . . . . . . . . 56 synchronisation . . . . . . . . . . . . . . . . 63 T W wallpaper . . . . . . . . . . . . . . . . . . . . . 56 Web bookmarks . . . . . . . . . . . . . . . . . 97 connect . . . . . . . . . . . . . . . . . . . 95 weight . . . . . . . . . . . . . . . . . . . . . . 106 wireless markup language . . . . . . . 95 wrist strap . . . . . . . . . . . . . . . . . . . . 16 write text . . . . . . . . . . . .
