User Manual

ManualsBrandsMicrosoft ManualsElectronicsGSM/WCDMA Radio Module

Wireless Platforms

CM/BU 1 (10)

RD-1/RD-2

Handling Guidelines for

PC OEMs

LEGAL NOTICE

The contents of this document are proprietary and confidential property of Nokia. This document is provided subject

to confidentiality obligations of the applicable agreement(s).

This document is intended for use of Nokia’s customers and collaborators only for the purpose for which this

document is submitted by Nokia. No part of this document may be reproduced or made available to the public or to

any third party in any form or means without the prior written permission of Nokia. This document is to be used by

properly trained professional personnel. Any use of the contents in this document is limited strictly to the use(s)

specifically authorized in the applicable agreement(s) under which the document is submitted.

Nokia operates a policy of ongoing development. Nokia reserves the right to make changes and improvements to

any of the products and/or services described in this document or withdraw this document at any time without prior

notice.

The contents of this document are provided "as is". Except as required by applicable law, no warranties of any kind,

either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a

particular purpose, are made in relation to the accuracy, reliability or contents of this document. NOKIA SHALL

NOT BE RESPONSIBLE IN ANY EVENT FOR ERRORS IN THIS DOCUMENT OR FOR ANY LOSS OF DATA OR

INCOME OR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT OR DIRECT DAMAGES

HOWSOEVER CAUSED, that might arise from the use of this document or any contents of this document.

This document and the product(s) it describes are protected by copyright according to the applicable laws.

Nokia is a registered trademark of Nokia Corporation. Other product and company names mentioned herein may

be trademarks or trade names of their respective owners.

Summary of content (10 pages)

PAGE 1
Wireless Platforms CM/BU 1 (10) RD-1/RD-2 Handling Guidelines for PC OEMs LEGAL NOTICE The contents of this document are proprietary and confidential property of Nokia. This document is provided subject to confidentiality obligations of the applicable agreement(s). This document is intended for use of Nokia’s customers and collaborators only for the purpose for which this document is submitted by Nokia.
PAGE 2
Wireless Platforms CM/BU 2 (10) TABLE OF CONTENTS TABLE OF CONTENTS............................................................................................................................. 2 1 Introduction ........................................................................................................................................ 3 2 FCC part 15 notice.............................................................................................................................
PAGE 3
Wireless Platforms CM/BU 1 3 (10) Introduction The purpose of this guideline is to enable mechanical and electrical installation of the RD-1/RD-2 WWAN module into a host laptop with the minimum of risk of damage to the module. Possible misuse cases are identified and mitigation defined. Failure to observe these guidelines at all times during the unpacking, handling and assembly processes may result in avoidable damage to the module.
PAGE 4
Wireless Platforms CM/BU 4 (10) 4 Unpacking The modules are shipped in either single module clamshell or 100 module trays 4.1 Individual Module Clamshell Figure 1: Representative* example of individual module Single clamshell with RD-1/RD-2 module The module should only be removed from the clamshell package directly before insertion into the host laptop.
PAGE 5
Wireless Platforms CM/BU 5 (10) The module should only be removed from the clamshell package directly before insertion into the host laptop. Before opening the packaging the correct orientation of the package top side must be checked and set from the package markings. The packaging is opened by placing the thumb in bottom of package bevelled slot, located each corners in package cover, and gently prising package cover and bottom off using the other thumb.
PAGE 6
Wireless Platforms CM/BU 6 (10) 6 Installation Prior to installation into the host laptop the laptop must be grounded and in a completely powered down state with the battery and any external power supplies removed. 6.1 Insertion into PCI Express Mini Card Connector The module shall be inserted according to the following steps: 1.
PAGE 7
Wireless Platforms CM/BU 7 (10) X X Safe Load Point Fixed Support Area Figure 5: Safe Load and Support Points (Module Installation) 6.1.1 Maximum Safe Load (Module Insertion) The maximum pressure applied to the point shown in Figure 5 and the resulting deformation shall not exceed that shown in the table below: Maximum Safe Load (N) 15 Corresponding Maximum Safe Deflection (mm) < 0.
PAGE 8
Wireless Platforms CM/BU 8 (10) 6.2 Antenna Connection The antenna coaxial shall be connected only after the module has been seated in the host laptop and according to the following steps below: 1. Offer the female plug up to the module socket ensuring that the barrels of both connecting parts are parallel. 2. Press gently on the back plate of the female plug in the same plane as the barrels of both connecting parts. 3. Remove pressure as soon as the connection is made.
PAGE 9
Wireless Platforms CM/BU 9 (10) 6.3 Antenna Disconnection The antenna shall be disconnected according to the following steps: 1. Hook the u-shaped end of the Antenna Extraction Tool* under the female plug. NOTE: The module shall remain seated in the host laptop prior to antenna disconnection 2. Gentle apply tension to the tool. 3. As soon as disconnection is noted relax the tension on the tool 4. Carefully withdraw the female plug ensuring that no load is place upon the coaxial cable.
PAGE 10
Wireless Platforms CM/BU 10 (10) 6.4 Removal from PCI Express Mini Card Connector The module shall be removed according to the following steps: 1. Press gently on the retaining latches until the module is unseated and free to rise. 2. Module edge rises up automatically by the mechanical property of PCI Express Mini Card Connector. 3. Gently slide the module from receptacle at the point indicated in Figure 3 STEP: 1. 2. 3.