npl-2_en1_1.
FCC_Layout.fm Page 91 Monday, February 10, 2003 5:16 PM The wireless phone described in this guide is approved for use in GSM 900, 1800 and 1900 networks. LEGAL INFORMATION Part No. 9354993 Issue No. 1 Copyright ©2003 Nokia. All rights reserved. Nokia is a registered trademark of Nokia Corporation. Nokia, Nokia Connecting People, Xpress-on, Pop-Port, the Original Accessories logos, Space Impact, Snake II, and Bumper are trademarks of Nokia Corporation and/or its affiliates.
npl-2_en1_1.fm Page 3 Wednesday, August 7, 2002 1:56 PM Contents Contents FOR YOUR SAFETY................... 5 General information 7 Stickers in the sales package ............. 7 Access codes ........................................... 7 Overview of the functions in the phone ........................................ 9 Multimedia messaging service (MMS)......................................... 9 Polyphonic sound (MIDI) ..................... 9 General Packet Radio Service (GPRS) 9 Loudspeaker ...........
npl-2_en1_1.fm Page 4 Wednesday, August 7, 2002 1:56 PM Contents memory full....................................... Erasing messages............................. Chat..................................................... Voice messages ................................ Info messages ................................... Message settings ............................. Service commands .......................... Call register (Menu 2)........................ Recent calls lists ..............................
npl-2_en1_1.fm Page 5 Monday, September 2, 2002 2:35 PM FOR YOUR SAFETY FOR YOUR SAFETY Read these simple guidelines. Breaking the rules may be dangerous or illegal. Further detailed information is given in this manual. Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger. ROAD SAFETY COMES FIRST Don't use a hand-held phone while driving. INTERFERENCE All wireless phones may get interference, which could affect performance.
npl-2_en1_1.fm Page 6 Monday, September 2, 2002 2:35 PM FOR YOUR SAFETY BACKUP COPIES Remember to make backup copies of all important data. WATER-RESISTANCE Your phone is not water-resistant. Keep it dry. CALLING Ensure the phone is switched on and in service. Enter the phone number, including the area code, then press . To end a call, press . To answer a call, press . EMERGENCY CALLS Ensure the phone is switched on and in service. Press as many times as needed (e.g.
npl-2_en1_1.fm Page 7 Monday, September 2, 2002 2:35 PM General information General information ■ Stickers in the sales package The stickers contain important information for services and customer support purposes. Attach the sticker to your warranty card. Attach the sticker to the Nokia Club Invitation Card supplied in the sales package. ■ Access codes • Security code (5 to 10 digits): The security code protects your phone against unauthorised use, and is supplied with the phone.
npl-2_en1_1.fm Page 8 Monday, September 2, 2002 2:35 PM General information • Barring password (4 digits): The barring password is needed when using the Call barring service, see Security settings on page 61. You can obtain the password from your service provider. • Signing PIN: The signing PIN is needed for the digital signature. See Digital signature on page 88. The signing PIN is supplied with the SIM card if the SIM card contains a security module.
npl-2_en1_1.fm Page 9 Monday, September 2, 2002 2:35 PM Overview of the functions in the phone Overview of the functions in the phone The Nokia 6100 phone provides many functions which are practical for daily use, such as Calendar, Clock, Alarm clock, Calculator, and many more. Also a range of Nokia Xpress-onTM colour covers is available for your phone. To change the cover, see Changing the front cover on page 20.
npl-2_en1_1.fm Page 10 Monday, September 2, 2002 2:35 PM Overview of the functions in the phone Before you can use GPRS technology • Contact your network operator or service provider for availability and subscription to the GPRS service. • Save the GPRS settings for each of the applications used over GPRS. See Setting up the phone for a WAP service on page 78, Message settings on page 48 and GPRS on page 76.
npl-2_en1_1.fm Page 11 Monday, September 2, 2002 2:35 PM Overview of the functions in the phone ■ Dynamic memory Your phone uses dynamic memory for some functions. Dynamic memory means that the phone’s memory is shared between different functions. In addition to the dynamic memory, a minimum amount of memory is reserved for each of the functions. The phone displays a note if there is not enough memory for a function.
npl-2_en1_1.fm Page 12 Monday, September 2, 2002 2:35 PM Your phone 1. Your phone ■ Keys and connectors 1. Power key Switches the phone on and off. For example, when the keypad is locked, pressing the power key briefly turns the phone’s display lights on for approximately 15 seconds. 2. Volume keys Keys to adjust the earpiece, headset and loudspeaker volume. 3.
npl-2_en1_1.fm Page 13 Monday, September 2, 2002 2:35 PM Your phone 1. Charger connector 2. Pop-PortTM connector for headset and data cable, for example 3. Infrared (IR) port ■ Standby mode When the phone is ready for use, and you have not keyed in any characters, the phone is in standby mode. 1. Indicates in which cellular network the phone is currently being used. 2. Shows the signal strength of the cellular network at your current location. The higher the bar, the stronger the signal. 3.
npl-2_en1_1.fm Page 14 Monday, September 2, 2002 2:35 PM Your phone Essential indicators in standby mode You have received one or several text or picture messages. See Reading and replying to a message or an e-mail on page 40. You have received one or several multimedia messages. See Reading and replying to a multimedia message on page 45. You have received one or several voice messages. See Voice messages on page 47. The phone’s keypad is locked. See Keypad lock (Keyguard) on page 19.
npl-2_en1_1.fm Page 15 Monday, September 2, 2002 2:35 PM Your phone The loudspeaker has been activated, see Loudspeaker on page 24. Calls are limited to a closed user group. See Security settings on page 61. The timed profile is selected. See Profiles (Menu 3) on page 53. , or Headset, handsfree or loopset accessory is connected to the phone. To set the phone to show the time and date in standby mode, see Clock on page 54 and Date on page 54.
npl-2_en1_1.fm Page 16 Monday, September 2, 2002 2:35 PM Getting started 2. Getting started ■ Installing the SIM card and the battery Keep all miniature SIM cards out of the reach of small children. • The SIM card and its contacts can easily be damaged by scratches or bending, so be careful when handling, inserting or removing the card. • Before removing the battery switch off the phone. 1.
npl-2_en1_1.fm Page 17 Monday, September 2, 2002 2:35 PM Getting started 3. Insert the SIM card into the SIM card holder (6). Make sure that the SIM card is properly inserted and that the golden contact area on the card is faced like shown. 4. Close the SIM card holder (7) and press it as it locks. 5. Insert the battery (8). 6. Slide the back cover into its place (9).
npl-2_en1_1.fm Page 18 Monday, September 2, 2002 2:35 PM Getting started ■ Charging the battery 1. Connect the lead from the charger to the socket on the bottom of your phone. 2. Connect the charger to an AC wall socket. The text Charging is displayed briefly if the phone is switched on. If the battery is completely empty, it may take a few minutes before the charging indicator appears on the display or any calls can be made. You can use the phone while the charger is connected.
npl-2_en1_1.fm Page 19 Monday, September 2, 2002 2:35 PM Getting started ■ Normal operating position Use the phone only in its normal operating position. Your phone has a built-in antenna. As with any other radio transmitting device, do not touch the antenna unnecessarily when the phone is switched on. Contact with the antenna affects call quality and may cause the phone to operate at a higher power level than otherwise needed.
npl-2_en1_1.fm Page 20 Monday, September 2, 2002 2:35 PM Getting started ■ Changing the front cover Before changing the front cover, always switch off the power and disconnect the phone from the charger or any other device. Always store and use the phone with the covers attached. 1. Remove the back cover of the phone. See step 1 in Installing the SIM card and the battery on page 16. 2.
npl-2_en1_1.fm Page 21 Monday, September 2, 2002 2:36 PM Getting started 4. To attach the front cover, first place the back part of the phone and the front cover properly together and then gently push on the bottom and the top of the phone until the catches are locked properly. 5. Slide the back cover into its place. See step 6 in Installing the SIM card and the battery on page 16.
npl-2_en1_1.fm Page 22 Monday, September 2, 2002 2:36 PM Call functions 3. Call functions ■ Making a call 1. Key in the phone number, including the area code. If you key in a wrong character, press Clear to delete it. For international calls, press twice for the international prefix (the + character replaces the international access code) and then key in the country code, area code without the leading 0, if necessary, and the phone number. 2. Press to call the number. 3.
npl-2_en1_1.fm Page 23 Monday, September 2, 2002 2:36 PM Call functions Making a conference call Conference calling is a network service that allows up to six persons to take part in a conference call. 1. Make a call to the first participant. 2. To make a call to a new participant, press Options and select New call. 3. Key in, or retrieve from the phone book, the phone number of the new participant and press Call. The first call is put on hold. 4.
npl-2_en1_1.fm Page 24 Monday, September 2, 2002 2:36 PM Call functions ■ Options during a call Many of the options that you can use during a call, are network services. Press Options during a call for some of the following options: Mute or Unmute, End call, End all calls, Phone book, Menu and Hold or Unhold, New call, Conference, Private, Answer, Reject and Loudspeaker or Handset. Lock keypad to activate the keypad lock. Send DTMF to send DTMF tone strings, for example, passwords or bank account numbers.
npl-2_en1_1.fm Page 25 Monday, September 2, 2002 2:36 PM Writing text 4. Writing text You can key in text, for example when writing messages, using the traditional or predictive text input. When you are writing text, the predictive text input is indicated by and the traditional text input by at the top left of the display. The character case is indicated by , , or next to the text input indicator. You can change the character case by pressing .
npl-2_en1_1.fm Page 26 Monday, September 2, 2002 2:36 PM Writing text More instructions for writing text, see Tips for writing text on page 27. 2. When you have finished writing the word and it is correct, confirm it by adding a space with or by pressing any of the scroll keys. Pressing a scroll key also moves the cursor. If the word is not correct, press repeatedly or press Options and select Matches. When the word you want appears, confirm it.
npl-2_en1_1.fm Page 27 Monday, September 2, 2002 2:36 PM Writing text ■ Tips for writing text The following functions may also be available for writing text: • To insert a space, press . • To move the cursor to the left, right, down or up, press the scroll keys , , or , respectively. • To delete a character to the left of the cursor, press Clear. Press and hold Clear to delete the characters more quickly. To delete all the characters at once when writing a message, press Options and selectClear text.
npl-2_en1_1.fm Page 28 Monday, September 2, 2002 2:36 PM Phone book (Names) 5. Phone book (Names) You can save names and phone numbers in the phone’s memory (internal phone book) and in the SIM card’s memory (SIM phone book). • The internal phone book may save up to 300 names with numbers and textual notes for each name. How many names can be saved depends on the length of the names, and the number and length of phone numbers and text items.
npl-2_en1_1.fm Page 29 Monday, September 2, 2002 2:36 PM Phone book (Names) 4. When the name and number are saved, press Done. Tip: Quick save In standby mode, key in the phone number. Press Options, and select Save. Key in the name, press OK and Done. Saving multiple numbers and text items per name You can save different types of phone numbers and short text items per name in the phone’s internal phone book.
npl-2_en1_1.fm Page 30 Monday, September 2, 2002 2:36 PM Phone book (Names) ■ Searching for a name in the phone book 1. Press Names and select Search. 2. You can key in the first characters of the name you are searching for in the pop-up window. Press and to scroll through the names in the list, and to move the cursor in the pop-up window. and 3. Scroll to the name you want, and press Details. Scroll to view the details of the selected name.
npl-2_en1_1.fm Page 31 Monday, September 2, 2002 2:36 PM Phone book (Names) 3. Select One by one, All or Default nos.. • If you select One by one, scroll to the name you want to copy and press Copy. Default nos. is shown if you copy from the phone to the SIM card. Only the default numbers will be copied. 4. To choose whether you want to keep or delete the original names and numbers, select Keep original or Move original. • If you select All or Default nos.
npl-2_en1_1.fm Page 32 Monday, September 2, 2002 2:36 PM Phone book (Names) ■ Speed dials To make a call by using the speed dialling keys, see Speed dialling a phone number on page 22. Assigning a number to a speed dialling key Press Names, select Speed dials and scroll to the speed dialling key number you want. Press Assign, press Search, and select first the name and then the number you want to assign.
npl-2_en1_1.fm Page 33 Monday, September 2, 2002 2:36 PM Phone book (Names) ■ Caller groups You can arrange the names and phone numbers saved in the phone book into caller groups. For each caller group, you can set the phone to play a specific ringing tone and show a selected logo on the display when you receive a call from a phone number in the group, see below. To set the phone to ring only upon calls from phone numbers belonging to a selected caller group, see Alert for in Tone settings on page 60.
npl-2_en1_1.fm Page 34 Monday, September 2, 2002 2:36 PM Using the menu 6. Using the menu The phone offers you an extensive range of functions which are grouped in menus. Most of the menu functions are provided with a brief help text. To view the help text, scroll to the menu function you want and wait for 15 seconds. To exit the help text, press Back. See Help text activation on page 58. ■ Accessing a menu function By scrolling 1. To access the menu, press Menu. 2.
npl-2_en1_1.fm Page 35 Monday, September 2, 2002 2:36 PM Using the menu ■ List of menu functions 1. Messages 1. Text messages 1. Create message 2. Inbox 3. Create e-mail 4. Sent items 5. Archive 6. Templates 7. My folders 8. Distribution lists 9. Delete messages 2. Multimedia msgs. 1. Create message 2. Inbox 3. Outbox 4. Sent items 5. Saved items 6. Delete messages 3. Chat 4. Voice messages 1. Listen to voice messages 2. Voice mailbox number 5. Info messages 1. Info service 2. Topics 3. Language 4.
npl-2_en1_1.fm Page 36 Monday, September 2, 2002 2:36 PM Using the menu 4. Outdoor (same submenus as in General) 5. Pager (same submenus as in General) 4. Settings 1. Time and date settings 1. Clock 2. Date 3. Auto-update of date & time 2. Call settings 1. Call divert 2. Anykey answer 3. Automatic redial 4. Speed dialling 5. Call waiting service 6. Summary after call 7. Send my caller identity 8. Line for outgoing calls1 3. Phone settings 1. Language 2. Automatic keyguard 3. Cell info display 4.
npl-2_en1_1.fm Page 37 Monday, September 2, 2002 2:36 PM Using the menu 7. Organiser 1. Calendar 2. To-do list 8. Games 1. Select game 2. Game services 3. Memory 4. Settings 1. Game sounds 2. Game lights 3. Shakes 4. Club Nokia ID 9. Applications 1. Select application 2. App. services 3. Memory 10.Extras 1. Calculator 2. Countdown timer 3. Stopwatch 4. Wallet 1. Cards 2. Personal notes 3. Settings 11.Connectivity 1. Infrared 2. GPRS 1. GPRS connection 2. GPRS modem settings 12.Services 1. Home 2.
npl-2_en1_1.fm Page 38 Monday, September 2, 2002 2:36 PM Menu functions 7. Menu functions ■ Messages (Menu 1) You can read, write, send and save text, multimedia, and e-mail messages. All the messages are organised in folders. Before you can send any text, picture, and e-mail messages, you need to save your message centre number, see Message settings on page 48. Text messages Your phone is able to send and receive multi-part messages made of several ordinary text messages (network service).
npl-2_en1_1.fm Page 39 Monday, September 2, 2002 2:36 PM Menu functions 4. Enter the recipient’s phone number or search for the phone number in the phone book. Press OK to send the message. Note: When sending messages via the SMS network service, your phone may display the words Message sent. This is an indication that the message has been sent by your phone to the message centre number programmed into your phone. This is not an indication that the message has been received at the intended destination.
npl-2_en1_1.fm Page 40 Monday, September 2, 2002 2:36 PM Menu functions See also Inserting a text template in a message or in an e-mail on page 41. Inserting a picture is not possible. 5. To send the e-mail, press Options and selectSend e-mail. If you have not saved the settings for e-mail sending, the phone asks for the email server number. Press OK to send the e-mail. Note: When sending e-mails via the SMS network service, your phone may display the words Message sent.
npl-2_en1_1.fm Page 41 Monday, September 2, 2002 2:38 PM Menu functions Select Message details to view the sender’s name and phone number, the message centre used, reception date and time. Select Use detail to extract numbers, e-mail addresses and website addresses from the current message. When reading a picture message, select Save picture to save the picture in the Templates folder. 4. Select Reply to reply to a message.
npl-2_en1_1.fm Page 42 Monday, September 2, 2002 2:38 PM Menu functions characters that you can enter in a message, depends on the size of the picture. To view the text and the picture together before sending the message, press Options and select Preview. Archive folder and my folders To organise your messages, you can move some of your messages to the Archive folder, or add new folders for your messages. While reading a message, press Options.
npl-2_en1_1.fm Page 43 Monday, September 2, 2002 2:38 PM Menu functions To edit the content of a distribution list, you have to be in the list view with the option View list. Press Options to get the following options to edit the content of a distribution list: • Add name to add a name to the distribution list. • View details to view the details of the selected name. • Delete name to delete the selected name in the distribution list.
npl-2_en1_1.fm Page 44 Monday, September 2, 2002 2:38 PM Menu functions Multimedia messaging supports the following formats: • Picture: JPEG, GIF, PNG, and BMP. • Sound: Scalable Polyphonic MIDI (SP-MIDI) and monophonic ringing tones.
npl-2_en1_1.fm Page 45 Monday, September 2, 2002 2:38 PM Menu functions 4. To send the message, press Options and select Send to number (or Send to e-mail). 5. Enter the recipient’s phone number (or e-mail address) or search for the phone number (or e-mail address) in the phone book. Press OK and the message is moved to the Outbox folder for sending. Sending a multimedia message takes more time than sending a text message.
npl-2_en1_1.fm Page 46 Monday, September 2, 2002 2:38 PM Menu functions • Message details to view the message subject, size and class. • Play to listen to the sound in the message. • Save sound clip to save the sound in the Gallery. • Zoom in to zoom the picture in the message bigger. • Save image to save the picture in the Gallery. Inbox, Outbox, Saved and Sent items folders The phone saves the received multimedia messages in the Inbox folder of the Multimedia msgs. submenu.
npl-2_en1_1.fm Page 47 Monday, September 2, 2002 2:38 PM Menu functions 2. To delete all the messages in a folder, scroll to the folder and press OK. Then press OK when Delete all read messages from folder? is displayed. To delete all read messages from all the folders, scroll to All read and press OK . Then press OK when Delete read messages from all folders? is displayed. Chat You can have a conversation with another person using this text messaging application.
npl-2_en1_1.fm Page 48 Monday, September 2, 2002 2:38 PM Menu functions Press Menu, and select Messages and Voice messages. Select • Listen to voice messages to call your voice mailbox at the phone number you have saved within the Voice mailbox number menu. Each phone line may have its own voice mailbox number, see Line for outgoing calls on page 56. • Voice mailbox number to key in, search for or edit your voice mailbox number and press OK to save it.
npl-2_en1_1.fm Page 49 Monday, September 2, 2002 2:38 PM Menu functions • Select Message validity to select the time for how long the network should attempt to deliver your message. • For message type Text, select Default recipient number to save a default number to send messages for this message profile. For message type E-mail, select E-mail server to save the e-mail server number. • Select Delivery reports to request the network to send delivery reports on your messages (network service).
npl-2_en1_1.fm Page 50 Monday, September 2, 2002 2:38 PM Menu functions • Incoming multimedia messages. Select Retrieve to set the phone automatically to fetch received multimedia messages, or select Reject if you do not wish to receive multimedia messages. • Connection settings. Define WAP connection settings for retrieving multimedia messages. Activate the set where you want to save the connection settings and then edit the settings. Refer also Keying in the service settings manually on page 79.
npl-2_en1_1.fm Page 51 Monday, September 2, 2002 2:38 PM Menu functions Service commands Press Menu, and select Messages and Service commands. Key in and send service requests (also known as USSD commands) such as activation commands for network services, to your service provider. ■ Call register (Menu 2) The phone registers the phone numbers of missed, received and dialled calls, and the approximate length and cost of your calls.
npl-2_en1_1.fm Page 52 Monday, September 2, 2002 2:38 PM Menu functions only those numbers in the missed calls, received calls or dialled numbers lists. You cannot undo the operation. Call counters and call timers Note: The actual invoice for calls and services from your service provider may vary, depending upon network features, rounding-off for billing, taxes and so forth.
npl-2_en1_1.fm Page 53 Monday, September 2, 2002 2:38 PM Menu functions ■ Profiles (Menu 3) Your phone has various setting groups, profiles, for which you can customise the phone tones for different events and environments. At first, personalise the profiles to your liking and then you only need to activate a profile to use it. Available profiles are General, Silent, Meeting, Outdoor, and Pager. Press Menu, and select Profiles. Scroll to a profile and press Select.
npl-2_en1_1.fm Page 54 Monday, September 2, 2002 2:38 PM Menu functions ■ Settings (Menu 4) Time and date settings Clock Press Menu, and select Settings, Time and date settings and Clock. Select Show clock to show the clock on the top right of the display in standby mode. Select Set the time, to adjust the clock to the right time, and Time format to select the 12-hour or 24-hour time format.
npl-2_en1_1.fm Page 55 Monday, September 2, 2002 2:38 PM Menu functions your service provider. Divert options not supported by your SIM card or your network operator may not be shown. Select the divert option you want, for example, select Divert if busy to divert the voice calls when your number is busy or when you reject an incoming call. To set the divert setting to on, select Activate, to set the divert setting to off, select Cancel, or Check status to check whether the divert is activated or not.
npl-2_en1_1.fm Page 56 Monday, September 2, 2002 2:38 PM Menu functions Summary after call Press Menu, and select Settings, Call settings and Summary after call. Select On and the phone will briefly display the duration and cost (network service) of the last call. Send my caller identity Press Menu, and select Settings, Call settings and Send my caller identity. Select Yes and your phone number will be displayed to the person you are calling (network service).
npl-2_en1_1.fm Page 57 Monday, September 2, 2002 2:38 PM Menu functions You can set the keypad of your phone to lock automatically after a preset time delay. You can set the delay time from 10 seconds up to 60 minutes and when the time is up, the keypad locks automatically preventing accidental keypresses. Press Menu, and select Settings, Phone settings and Automatic keyguard. • To activate the automatic keyguard, select On and the phone displays Set delay:. Key in the time and press OK.
npl-2_en1_1.fm Page 58 Monday, September 2, 2002 2:38 PM Menu functions Help text activation To set the phone to show or not to show the help texts, press Menu, and select Settings, Phone settings and Help text activation. See also Using the menu on page 34. Start-up tone To set the phone to play or not to play a start-up tone when the phone is switched on, press Menu, and select Settings, Phone settings and Startup tone.
npl-2_en1_1.fm Page 59 Monday, September 2, 2002 2:38 PM Menu functions Colour schemes You can change the colour in some display components, for example, indicators and signal bars. Press Menu, and selectSettings, Display settings and Colour schemes. Select the desired colour scheme. Operator logo To set your phone to display or hide the operator logo, press Menu, and selectSettings, Display settings and Operator logo.
npl-2_en1_1.fm Page 60 Monday, September 2, 2002 2:38 PM Menu functions Tone settings Press Menu, and select Settings and then Tone settings. You can find the same settings in the Profiles menu, see Profiles (Menu 3) on page 53. Note that the settings you make, change the settings in the active profile. Select Incoming call alert to select how the phone notifies you of an incoming voice call. The options are Ringing, Ascending, Ring once, Beep once and Off. Select Ringing tone for incoming voice calls.
npl-2_en1_1.fm Page 61 Monday, September 2, 2002 2:39 PM Menu functions • Select Automatic answer to set the phone to answer an incoming call automatically after five seconds. If the Incoming call alert is set to Beep once or Off, automatic answer will not be in use. • Select Lights to set the lights permanently On. Select Automatic to set the lights on for 15 seconds after a keypress. The Lights option is available only when Handsfree is selected.
npl-2_en1_1.fm Page 62 Monday, September 2, 2002 2:39 PM Menu functions Restore factory settings To reset some of the menu settings to their original values, press Menu, and select Settings and Restore factory settings. Key in the security code and press OK. Note that the data you have keyed in or downloaded, for example, the names and phone numbers saved in the phone book are not deleted. ■ Alarm clock (Menu 5) The alarm clock uses the time format set for the clock.
npl-2_en1_1.fm Page 63 Monday, September 2, 2002 2:39 PM Menu functions You may save up to 60 ringing tones with an average size of 5kB of which 20 are removable and up to 35 images with an average size of 10kB. The gallery uses dynamic memory, see Dynamic memory on page 11. 1. Press Menu and select Gallery. The list of options is shown. 2. Select View folders to open the list of folders. Other options available are: • Delete folder to select the folder you want to delete.
npl-2_en1_1.fm Page 64 Monday, September 2, 2002 2:39 PM Menu functions 4. Scroll to the desired file. Press Options and some of the following options are available: • Open to open the seleted file. • Delete to delete the seleted file. • Set as wallpaper to set the selected file as wallpaper. • Set as ring tone to set the selected file as ringing tone. • Move to move a file to another folder. • Rename folder to give a new name for the file. • Details to see the details of the file, the size, for example.
npl-2_en1_1.fm Page 65 Monday, September 2, 2002 2:39 PM Menu functions The other options for the calendar views may include: • Options for making a note, for sending a note via IR, or as a note directly to another phone’s calendar or as a text message. • Options for deleting, editing, moving and repeating a note and for copying a note to another day. • Settings to set the date, time, date or time format, or the first day of the week.
npl-2_en1_1.fm Page 66 Monday, September 2, 2002 2:39 PM Menu functions • Reminder - Key in the subject for the reminder, press Options and select Save. To set the alarm for the note, select Alarm on and then set the alarm time. When you have set the alarm, the indicator view the notes. is displayed when you When the phone alarms for a note The phone beeps, and displays the note. With a call note on the display, you can call the displayed number by pressing .
npl-2_en1_1.fm Page 67 Monday, September 2, 2002 2:39 PM Menu functions ■ Games (Menu 8) Note: Your phone must be switched on to use this function. Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger. Launching a game 1. Press Menu, and select Games and Select game. 2. Scroll to a game or a game set (name depends on the game). 3. Press Options and select Open or press single game it will be launched. .
npl-2_en1_1.fm Page 68 Monday, September 2, 2002 2:39 PM Menu functions Memory status for games To view the size of memory available for game and application installations, press Menu, and select Games and Memory. You may save up to six applications and/or games with a maximum size of 64kB each. The games use dynamic memory, see Dynamic memory on page 11. Game settings Press Menu, and select Games and Settings to set sounds, lights and shakes for the game.
npl-2_en1_1.fm Page 69 Monday, September 2, 2002 2:39 PM Menu functions Other options available for an application or application set • Delete to delete the application or application set from the phone. Note that if you delete a pre-installed application or an application set from your phone, you may download it back to your phone from the Nokia Software Market, www.softwaremarket.nokia.com/wap. • Web access to restrict the application for accessing the network.
npl-2_en1_1.fm Page 70 Monday, September 2, 2002 2:39 PM Menu functions • Use the Java Application installer from PC Suite to download the applications in your phone. Note that Nokia does not warrant for applications from non-Nokia sites. If you choose to download Java applications from them, you should take the same precautions, for security or content, as you would with any site. Note that when downloading a game or an application, it may be saved in Games menu instead of the Applications menu.
npl-2_en1_1.fm Page 71 Monday, September 2, 2002 2:39 PM Menu functions Memory status for applications To view the size of memory available for game and application installations, press Menu, and select Applications and Memory. You may save up to six applications and/or games with a maximum size of 64kB each. The applications use dynamic memory, see Dynamic memory on page 11. ■ Extras (Menu 10) Note: Your phone must be switched on to use the functions in Extras menu.
npl-2_en1_1.fm Page 72 Monday, September 2, 2002 2:39 PM Menu functions Making a currency conversion 1. Press Menu, and select Extras and Calculator. 2. To save the exchange rate, press Options and select Exchange rate. Select either of the displayed options. Key in the exchange rate, press for a decimal point, and press OK. The exchange rate remains in the memory until you replace it with another one. 3.
npl-2_en1_1.fm Page 73 Monday, September 2, 2002 2:39 PM Menu functions Time observation and time splitting 1. Press Menu, and select Extras, Stopwatch and Split timing. You can select Continue if you have set the timing in the background. 2. Press Start to start the time observation. Press Split every time you want to take an intermediate time. The intermediate times are listed below the running time on the display. Scroll to view the times. 3. Press Stop to stop the time observation. 4.
npl-2_en1_1.fm Page 74 Monday, September 2, 2002 2:39 PM Menu functions When you access the wallet for the first time, you need to create your own wallet code. At Create wallet code: key in the code and press OK to confirm it and at Verify wallet code: key in the code again and press OK. If you want to delete all the content of the wallet and the wallet code, key in *#3925538# (*#ewallet# in letters) in standby mode. You also need the security code of the phone.
npl-2_en1_1.fm Page 75 Monday, September 2, 2002 2:39 PM Menu functions Wallet settings Press Menu, select Extras, Wallet and Settings. Select • Code request to set the wallet code request to on or off. You need to key in the correct wallet code before you can set the code request to on or off. • Change code to change the wallet code. Guidelines for paying your purchases with wallet 1.
npl-2_en1_1.fm Page 76 Monday, September 2, 2002 2:39 PM Menu functions Note: Your phone must be switched on to use this function. Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger. Sending and receiving data via IR • Ensure that the IR ports of the sending and receiving devices are pointing at each other and that there are no obstructions between the devices.
npl-2_en1_1.fm Page 77 Monday, September 2, 2002 2:39 PM Menu functions GPRS modem settings You can connect the phone via infrared or data cable connection to a compatible PC and use the phone as a modem to enable GPRS connectivity from the PC. Press Menu, and select Connectivity, GPRS and GPRS modem settings. Select Active access point and activate the access point you want to use. Select Edit active access point to change the access point settings. • Scroll to Alias for access point and press Select.
npl-2_en1_1.fm Page 78 Monday, September 2, 2002 2:39 PM Menu functions Basic steps for accessing and using WAP services 1. Save the service settings that are needed to access the WAP service that you want to use. See page 83. 2. Make a connection to the given WAP service. See page 80. 3. Start browsing the pages of the WAP service. See page 81. 4. Once you are finished browsing, end the connection to the WAP service. See page 83.
npl-2_en1_1.fm Page 79 Monday, September 2, 2002 2:39 PM Menu functions Keying in the service settings manually 1. Press Menu, and select Services, and Settings. 2. Select Active service settings. You need to activate the set where you want to save the service settings. A set is a collection of settings needed for making a connection to a WAP service. 3. Scroll to the set you would like to activate and press Activate. 4. Select Edit active service settings.
npl-2_en1_1.fm Page 80 Monday, September 2, 2002 2:39 PM Menu functions • Data call speed - Select the speed you want to use, or select Automatic. Automatic is available only if the current selected data call type is Analogue. The actual data call speed depends on the service provider. • Login type - Select Manual or Automatic. • User name - Key in the user name and press OK. • Password - Key in the password and press OK.
npl-2_en1_1.fm Page 81 Monday, September 2, 2002 2:40 PM Menu functions • Open the homepage of the WAP service: Press Menu, and select Services and Home. Tip: To quickly open the homepage, press and hold standby mode. in OR • Select a bookmark of the WAP service: Press Menu, and select Services, Bookmarks, and select a bookmark. If the bookmark does not work with the current active service settings, activate another set of service settings and try again.
npl-2_en1_1.fm Page 82 Monday, September 2, 2002 2:40 PM Menu functions Options while browsing Press Options and select one of the options available. The service provider may also offer other options. Select • Home to go back to the homepage of the WAP service. • Bookmarks. See page 84. • Call / Edit / Open row / Open link / Open list to call, to key in text or to select a highlighted item on the WAP page. • Add bookmark to save the WAP page as a bookmark.
npl-2_en1_1.fm Page 83 Monday, September 2, 2002 2:40 PM Menu functions Ending a WAP connection To quit browsing and to end the connection, press Options and select Quit. When Quit browsing? is shown, press Yes. Alternatively, press . If GSM data is the selected data bearer, press twice. The phone ends the connection to the WAP service. Appearance settings of WAP browser 1. While browsing, press Options and select Appear.
npl-2_en1_1.fm Page 84 Monday, September 2, 2002 2:40 PM Menu functions Bookmarks You can save up to 30 WAP page addresses as bookmarks in the phone’s memory. 1. While browsing, press Options and select Bookmarks, or in standby mode, press Menu, and select Services and Bookmarks. 2. Scroll to the bookmark you want to use and press Options. 3. Select one of the following options: Go to to make a connection to the WAP page associated with the bookmark.
npl-2_en1_1.fm Page 85 Monday, September 2, 2002 2:40 PM Menu functions • If you press Exit the message is moved to the Service inbox. To access the Service inbox later, press Menu, and select Services, and Service inbox. To access the Service inbox while browsing, press Options and select Service inbox. Scroll to the message you want, press Options and select • Retrieve to activate the WAP browser and download the indicated content. • Details to display detailed information on the service notification.
npl-2_en1_1.fm Page 86 Monday, September 2, 2002 2:40 PM Menu functions The phone indicates if the identity of the WAP server or WAP gateway cannot be verified, if the WAP server or WAP gateway certificate is not authentic or if you do not have the correct authority certificate in your phone. Viewing the list of authority certificates Press Menu, select Services, and Settings. Select Authority certificates. See also Security info in Using the phone keys while browsing on page 81.
npl-2_en1_1.fm Page 87 Monday, September 2, 2002 2:40 PM Menu functions • Change signing PIN to select the signing PIN you want to change. Key in the current signing PIN code. Press Change and key in the new code twice. See also Access codes on page 7. Certificates There are three kinds of certificates; server certificates, authority certificates and user certificates.
npl-2_en1_1.fm Page 88 Monday, September 2, 2002 2:40 PM Menu functions Digital signature You can make digital signatures with your phone. The signature can be traced back to you via the user certificate that was used to perform the signature. Making the digital signature can be the same as signing your name to a paper bill, contract or other document. For issuing a digital signature, select a link on a WAP page, for example, the title of the book you want to buy and its price.
npl-2_en1_1.fm Page 89 Monday, September 2, 2002 2:40 PM PC Connectivity 8. PC Connectivity You can send and receive e-mails, and access the Internet when your phone is connected to a compatible PC via an IR connection or a data cable. You can use your phone with a variety of PC connectivity and data communications applications.
npl-2_en1_1.fm Page 90 Monday, September 2, 2002 2:40 PM PC Connectivity • Nokia 6100 data modem drivers enable you to use your phone as a modem. • Nokia Modem Options contains settings for HSCSD and GPRS connections. • Nokia Connection Manager to select the connection type between the PC and the phone. GPRS and HSCSD With your phone you can use GPRS (General Packet Radio Service) and HSCSD (High Speed Circuit Switched Data) high-speed data services.
npl-2_en1_1.fm Page 91 Wednesday, August 7, 2002 10:20 AM Battery statements 9. Battery statements ■ Charging and Discharging Your phone is powered by a rechargeable battery. Note that a new battery's full performance is achieved only after two or three complete charge and discharge cycles! The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery.
FCC_Layout.fm Page 92 Monday, September 2, 2002 2:52 PM 10. Technical Information Weight....................................77 grams (6.4 ounces) with BL-4C battery Battery....................................720 mAh Li-polymer Battery Networks................................Wireless networks GSM 900, 1800 and1900 Size (volume)........................3.69 cubic inches (60.3 cc) Frequency range (Tx) ..................................................GSM 900: 880 - 915 Mhz .....................................
FCC_Layout.fm Page 93 Wednesday, August 7, 2002 1:34 PM 11. Patents Manufactured or sold under one or more of the following US Patents. Asterisk (*) indicates design patents pending.
FCC_Layout.fm Page 94 Wednesday, August 7, 2002 1:34 PM CARE AND MAINTENANCE Your phone is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfil any warranty obligations and to enjoy this product for many years. • Keep the phone and all its parts and accessories out of the reach of small children. • Keep the phone dry.
FCC_Layout.fm Page 95 Wednesday, August 7, 2002 1:34 PM IMPORTANT SAFETY INFORMATION ■ Traffic safety Don’t use a hand-held telephone while driving a vehicle. If you’re using a hand-held phone, park the vehicle before conversing. Always secure the phone in its holder and don’t place the phone on the passenger seat or where it can break loose in a collision or sudden stop.
FCC_Layout.fm Page 96 Wednesday, August 7, 2002 1:34 PM ■ Hearing aids Some digital wireless phones may interfere with hearing aids. In the event of such interference, consult your wireless provider. Other medical devices Operation of any radio transmitting equipment, including cellular phones, may interfere with the functionality of inadequately protected medical devices.
FCC_Layout.fm Page 97 Wednesday, August 7, 2002 1:34 PM ■ Vehicles Only qualified personnel should install or service the phone in a vehicle. Faulty installation or service may be dangerous and invalidate the warranty. RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles (for example, electronic fuel injection systems, electronic anti-skid (anti-lock) braking systems, electronic speed control systems, air bag systems).
FCC_Layout.fm Page 98 Monday, February 10, 2003 4:10 PM MAKING AN EMERGENCY CALL Note: Some networks may require that a valid SIM card be properly inserted in the phone. Official emergency numbers vary by location (for example, 911 or other official emergency number). 1. If the phone is not on, switch it on. Check for adequate signal strength. 2. Press as many times as needed (for example, to exit a call, to exit a menu, etc.) to clear the display and ready the phone for calls. 3.
FCC_Layout.fm Page 99 Monday, February 10, 2003 4:10 PM certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.
FCC_Layout.fm Page 100 Wednesday, August 7, 2002 1:34 PM APPENDIX ■ A message from the CTIA © 2001 Cellular Telecommunications & Internet Association. All Rights Reserved. 1250 Connecticut Avenue, NW Suite 800, Washington, DC 20036. Phone: (202) 785-0081 Safety is the most important call you will ever make. A Guide to Safe and Responsible Wireless Phone Use Tens of millions of people in the u.s.
FCC_Layout.fm Page 101 Wednesday, August 7, 2002 1:34 PM When it comes to the use of wireless phones, safety is your most important call. Wireless Phone “Safety Tips” Below are safety tips to follow while driving and using a wireless phone which should be easy to remember. 1. Get to know your wireless phone and its features such as speed dial and redial. Carefully read your instruction manual and learn to take advantage of valuable features most phones offer, including automatic redial and memory.
FCC_Layout.fm Page 102 Wednesday, August 7, 2002 1:34 PM before you begin your trip or attempt to coincide your calls with times you may be stopped at a stop sign, red light or otherwise stationary. But if you need to dial while driving, follow this simple tip--dial only a few numbers, check the road and your mirrors, then continue. 7. Do not engage in stressful or emotional conversations that may be distracting.
FCC_Layout.fm Page 103 Wednesday, August 7, 2002 1:34 PM their responsibilities as safe drivers and good citizens. As we approach a new century, more and more of us will take advantage of the benefits of wireless telephones. And, as we take to the roads, we all have a responsibility to drive safely. The wireless industry reminds you to use your phone safely when driving. For more information, please call 1-888-901-SAFE. For updates: http://www.wow-com.com/consumer/issues/driving/ articles.
FCC_Layout.fm Page 104 Wednesday, August 7, 2002 1:34 PM authority to take action if wireless phones are shown to emit radiofrequency energy (RF) at a level that is hazardous to the user. In such a case, FDA could require the manufacturers of wireless phones to notify users of the health hazard and to repair, replace or recall the phones so that the hazard no longer exists.
FCC_Layout.fm Page 105 Wednesday, August 7, 2002 1:34 PM they can get from wireless phones. Base stations are thus not the subject of the safety questions discussed in this document. 3. What kinds of phones are the subject of this update? The term wireless phone refers here to hand-held wireless phones with built-in antennas, often called cell mobile or PCS phones.
FCC_Layout.fm Page 106 Wednesday, August 7, 2002 1:34 PM existence of any harmful health effects from wireless phone RF exposures. However, none of the studies can answer questions about long-term exposures, since the average period of phone use in these studies was around three years. 5.
FCC_Layout.fm Page 107 Wednesday, August 7, 2002 1:34 PM industry, and academic organizations. CTIA-funded research is conducted through contracts to independent investigators. The initial research will include both laboratory studies and studies of wireless phone users. The CRADA will also include a broad assessment of additional research needs in the context of the latest research developments around the world. 7.
FCC_Layout.fm Page 108 Wednesday, August 7, 2002 1:34 PM tissue-simulating model of the human head. Standardized SAR test methodology is expected to greatly improve the consistency of measurements made at different laboratories on the same phone. SAR is the measurement of the amount of energy absorbed in tissue, either by the whole body or a small part of the body. It is measured in watts/kg (or milliwatts/g) of matter.
FCC_Layout.fm Page 109 Wednesday, August 7, 2002 1:34 PM effects. Their recommendation to limit wireless phone use by children was strictly precautionary; it was not based on scientific evidence that any health hazard exists. 11. What about wireless phone interference with medical equipment? Radiofrequency energy (RF) from wireless phones can interact with some electronic devices.
FCC_Layout.fm Page 110 Wednesday, August 7, 2002 1:34 PM World Health Organization (WHO) International EMF Project http://www.who.int/emf National Radiological Protection Board (UK) http://www.nrpb.org.uk/ July 18, 2001 For updates: http://www.fda.
