M , user s guide.
Important Do not plug a phone jack (RJ-11) into any Ethernet (RJ-45) port on your switch. Doing so might damage the device. You must use twisted pair cables with RJ-45 connectors that conform to FCC standards in the device’s Ethernet ports. Important Ne branchez pas une ligne téléphonique dans aucuns des port de réseau (RJ45). Caution For use with UL Listed, CSA and GS approved personal computers. Not intended for use in machinery, medical, or industrial applications. For indoor use only.
contents. 1 Introduction ........................................................................................ 1 Do You Have Everything You Need to Install Your Switch? ............... 2 Your Switch and Its Connections ......................................................... 2 About Ethernet Connections ................................................................ 5 Straight-Through and Crossover Cables .......................................... 5 Connecting to Broadband Modems .....................
introduction. Introducing the Broadband Networking 5-Port Switch Congratulations on your purchase of the Microsoft® Broadband Networking 5-Port Switch. The switch can be used in a number of different ways. It will let you expand your existing Ethernet network by connecting additional computers, printers, scanners, and other Ethernet devices. The switch will also let you form a new local area network (LAN) by connecting two or more computers.
The 5-port switch will work with any 10 Mbps or 100 Mbps Ethernetbased network. Although this guide focuses on Windows-based computers, you can use the switch with nearly any operating system. For more information about setting up non-Windows-based networks, see the documentation for your operating system. Do You Have Everything You Need to Install Your Switch? Included in the Box: 5-Port Switch (MN-150) 3.
corresponds to one of the five ports on the back of the switch. The lights for each port will be on, off, or blinking, depending on the current network configuration and activity for that port. The Power light is to the left of the port indicator lights. The following table describes the meaning of each light. Light Condition Status Power On The switch is receiving power. Speed On The port is transmitting or receiving packets at 100 megabits per second (Mbps).
About Ethernet Connections Ethernet is the most commonly used wired network protocol, with connection speeds of 10 Mbps, 100 Mbps, or higher. Your switch will transmit data at either 10 or 100 Mbps. The switch’s autonegotiation feature automatically determines the rate of your network connections and uses the fastest speed available.
Straight-Through and Crossover Cables Data is sent and received through specific wires within an Ethernet cable. Depending on the arrangement of its sending and receiving wires, an Ethernet cable is either a “straight-through” type or a “crossover” type. The following diagram demonstrates how to differentiate between the two types. Straight-Through Ethernet Cable Crossover Ethernet Cable In a straightthrough cable, the order of the colored wires is the same at both ends.
2 planning. Planning Your Network Your Microsoft® Broadband Networking 5-Port Switch can be configured in several ways. This chapter will help you locate setup instructions for your network configuration. Each computer to be connected to the network must have an installed network adapter with an available Ethernet port, and an Ethernet cable. As you configure your network, it’s a good idea to keep network security in mind.
After you set up the switch by using Option A, your network will resemble this diagram: Active Internet Connection Broadband Modem (DSL or Cable) Base Station (Gateway or Router) 5-Port Switch Computers with Installed Ethernet Adapters If you disconnect existing network wires for use in a different location, be sure to consult the documentation for your existing network device to determine the necessary cable type.
Option B: I want to share files or printers between two or more computers that are not connected to the Internet. Your 5-port switch can be used to connect two or more computers in a local area network (LAN) that does not have Internet access. By using this setup option, you can connect up to five computers and share files and printers among them.
Option C: My broadband modem has a firewall, and I want to use the switch to add more computers to my network. In this configuration, your 5-port switch is attached by Ethernet cables to your broadband modem and to the computer that hosts the modem. The switch then serves as a central connection point for up to three additional computers. This option requires one Ethernet cable to connect the switch to your computer and an additional Ethernet cable for each additional computer.
Option D: My computer runs firewall software and is directly connected to my broadband modem. This setup option allows you to add one or more computers to a network that already has a computer equipped with Network Address Translation (NAT) or firewall software. In this configuration, the existing networked computer must have an available Ethernet port for connecting the switch.
You might also consider adding a Microsoft Broadband Networking Base Station to your network. A base station offers several advantages. It allows multiple computers to connect to the Internet through a secure connection. It uses Network Address Translation (NAT) software to hide your computer from unauthorized access outside your network. Using a base station also allows you to turn off any computer on your network without interfering with another computer’s Internet access.
3 setting up. Installing and Connecting Your 5-Port Switch This chapter will guide you through the process of connecting the Microsoft® Broadband Networking 5-Port Switch. Your connection process might vary, depending on the setup option you selected in Chapter 2. Step 1: Choose a Location for Your Switch Caution To prevent major damage that can result from a sudden power outage, connect all computer and electronic equipment to a surge protector.
3. Connect each remaining computer or device to the switch by using a straight-through or crossover Ethernet cable. After you have finished connecting your switch, your setup will resemble the following illustration. Computer Note Although it does not matter which port you use to connect network devices, you might want to connect your switch to port 1 for easy reconfiguration and troubleshooting. Switch To Power Outlet To Modem Blue Ethernet Cable Step 4: Test Your Switch 1.
4 security. Securing Your Network Protecting your data and programs from security threats, such as computer viruses and hackers, is very important. This chapter provides general information about steps you can take to protect your network. Protect Your Network from Computer Viruses A switch will not provide security for your network, because it simply passes data from one cable to another.
Protect Your Network from Hackers If you have not already done so, consider purchasing the Microsoft® Broadband Networking Wired Base Station to establish a security layer between your network computers and the Internet. The security mechanisms provided by the base station include a firewall and Network Address Translation (NAT). A firewall is a barrier that helps protect your network from outside intruders.
5 troubleshooting. Diagnosing and Solving Problems with Your 5-Port Switch This chapter will help you solve installation and setup problems with your Microsoft® Broadband Networking 5-Port Switch. The following areas are covered: Note Checking the status of your Internet connection, network, and computer on every computer on the network is a quick way to determine how large a problem is.
Network and Internet Problems This section will help you solve common installation and setup problems as you integrate the switch with a new or existing network. My computers recognize my network, but it is not working correctly. O Verify that you have the correct network settings. Incorrect network settings will prevent networked computers from communicating properly.
My existing network used to work, but now it doesn’t. O Check the existing network installation to verify that all cables are still attached and all link/activity lights on the other network devices read correctly. O Verify that the network settings on all of the computers are correct. My newly networked computer sees my network but can’t find the Internet. O Check the Internet settings on another computer in the network.
Windows 2000: 1. Click Start, point to Settings, and then click Control Panel. 2. Double-click System. 3. Click the Network Identification tab. Windows 98, Windows 98 SE, and Windows Me: 1. Click Start, point to Settings, and then click Control Panel. 2. Double-click Network, and then click the Identification tab. If you need to change your workgroup name on a computer, click Change, and then type the correct workgroup name.
My printer is connected directly to my network, and I cannot access the printer from the computers on my network. O Check to make sure that the printer is turned on. O Verify that all network cables between the computers and the printer are securely connected. You can check to see if the network recognizes the connection by inspecting the link lights associated with the Ethernet ports on your hardware. When the cable is connected successfully, the link light should be illuminated.
reference. Getting Help Visit Us on the Web Please visit our Web site at http://www.microsoft.com/broadbandnetworking/ Technical Support Product Name: Microsoft® Broadband Networking 5-Port Switch Support Information Online: http://support.microsoft.com/directory/productsupportoption.asp In Canada, visit http://www.microsoft.ca/support/ Online Support: Work with a Microsoft Support Professional over the Internet. Submit your issue online: http://support.microsoft.com/directory/onlinesr.
Regulatory Information United States Radio and TV Interference Regulations This device complies with Part 15 of the U.S. Federal Communications Commission (FCC) rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The Microsoft hardware device(s) that accompanies this software can radiate radio frequency (RF) energy.
Limited Warranty PLEASE READ THIS MANUFACTURER’S GUARANTEE CAREFULLY TO UNDERSTAND YOUR RIGHTS AND OBLIGATIONS MANUFACTURER’S GUARANTEE AND LIMITATION OF LIABILITY NOTE: The following guarantee is not restricted to any territory and does not affect any statutory rights that you may have. The term “Hardware Device” means the enclosed Microsoft Hardware Device. This Manufacturer’s Guarantee does not cover your data, or any separate software, whether or not packaged or included with the Hardware Device.
Limited Warranty Continued VEUILLEZ VOUS ASSURER QU’APRÈS UNE LECTURE ATTENTIVE VOUS AYEZ BIEN COMPRIS L’ENSEMBLE DES DROITS ET LIMITATIONS EXPOSÉES DANS CETTE GARANTIE DU FABRICANT GARANTIE ET EXCLUSION DE RESPONSABILITÉ DU FABRICANT REMARQUE : La garantie ci-dessous n’est pas limitée à un territoire particulier, et n’influence en aucune manière les droits légaux dont vous disposez. « Dispositif matériel » désigne le dispositif matériel Microsoft ci-inclus.
Technical Specifications 5-Port Switch Standards IEEE 802.3 Ethernet; IEEE 802.3u Fast Ethernet; Network Interface Five 10/100 Mbps switched Ethernet/IEEE 802.
glossary. This glossary contains common terms for wired and wireless networking. 100Base-T Also known as “Fast Ethernet,” an Ethernet cable standard with a data transfer rate of up to 100 Mbps. 10Base-T An older Ethernet cable standard with a data transfer rate of up to 10 Mbps. 802.11, 802.11b A family of IEEE-defined specifications for wireless networks. Includes the 802.11b standard, which supports high-speed (up to 11 Mbps) wireless data transmission.
client/server network A network of two or more computers that rely upon a central server to mediate the connections or provide additional system resources. This dependence upon a server differentiates a client/ server network from a peer-to-peer network. computer name A name that uniquely identifies a computer on the network so that all its shared resources can be accessed by other computers on the network. One computer’s name cannot be the same as any other computer or domain name on the network.
encryption Ethernet Ethernet cable firewall The process of encoding data to prevent unauthorized access, especially during transmission. Microsoft wireless hardware relies upon encryption to ensure that data transmissions cannot be accessed by users outside the network. Also see WEP. A networking standard that uses cables to provide network access. A type of cable that facilitates network communications.
LAN MAC address Mbps modem Acronym for “local area network.” A group of computers and other devices dispersed over a relatively limited area (for example, a building) and connected by a communications link that enables any device to interact with any other on the network. Acronym for “media access control” address. The address that is used for communication between network adapters on the same subnet. Each network adapter is manufactured with its own unique MAC address.
PPPoE Acronym for “Point-to-Point Protocol over Ethernet.” A specification for connecting users on an Ethernet network to the Internet by using a broadband connection (typically through a DSL modem). Microsoft Broadband Networking hardware supports PPPoE for connections that require it. protocol A set of rules that computers use to communicate with each other over a network. RJ-11 connector An attachment used to join a telephone line to a device such as a modem.
USB USB adapter USB connector Acronym for “universal serial bus.” A hardware standard for easily connecting peripherals to a computer system. A device that connects to a USB port; the Microsoft Broadband Networking Wireless USB Adapter is a type of USB adapter. The end of the USB cable that is plugged into a USB port. USB port A rectangular slot in a computer into which a USB connector is inserted. WAN Acronym for “wide area network.
My Network Settings Use this page to record your network settings. Workgroup or domain name: Base station password (if applicable): Wide Area Network (WAN) Settings Complete this section only if your network has a base station (gateway or router). You can obtain this information from your Internet service provider (ISP). Your ISP might not require all of the settings listed below. Dynamic IP (DHCP) Settings Complete this section only if your ISP uses a DHCP connection.
M 0802 Part No. X08-85249-02 www.microsoft.
