Nokia Car Kit CK-200 User and Installation Guide 9220825 Issue 1 EN
DECLARATION OF CONFORMITY Hereby, NOKIA CORPORATION declares that this CK-200 product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The product is in conformity with the limits defined in Directive 2004/104/EC (amending Directive 72/245/ EEC), Annex I, paragraph 6.5, 6.6, 6.8 and 6.9. A copy of the Declaration of Conformity can be found at http://www.nokia.com/phones/declaration_of_conformity/. © 2010 Nokia. All rights reserved.
Contents For your safety......................... 5 Quick start................................ 6 First time setup ...................................... 6 Remote control ...................................... 6 1. Introduction ......................... 8 About this document............................ 8 Software updates .................................. 8 Bluetooth wireless technology .......... 9 2. Get started.......................... 10 Parts ........................................................
Installation using the ISO cable CA-160..................... Installation using the power cable CA-153P and an external speaker................................................ Installation using the power cable CA-153P and direct input cable CA-161......................... Optional accessories........................... Charging cable ................................. Microphone ....................................... External antenna ............................. 4 37 Check the operation of the car kit.
For your safety For your safety Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user and installation guide for further information. SWITCH ON SAFELY Do not switch the device on when wireless phone use is prohibited or when it may cause interference or danger. ROAD SAFETY COMES FIRST Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety.
Quick start Quick start This section briefly describes the basic features of the car kit. For details, see the respective sections in this guide. ■ First time setup 1. Switch on the car kit (see p. 15) and your mobile device. 2. If you are prompted to select a language, turn the NaviTM wheel (hereafter referred to as wheel) to scroll to the desired language, and press the wheel. 3. Activate Bluetooth on your device, and set up a Bluetooth connection between the car kit and the device. ■ Remote control 1.
Quick start • To adjust the volume during a call or to scroll through menu items, turn the wheel left or right. • To select, for example, Menu in standby mode or the highlighted function in the menu, press the wheel. 4. Call key • To make or answer a call or to switch between an active call and a call on hold, press the call key. • To view the list of last dialled numbers in standby mode, press the call key. • To redial the last dialled number in standby mode, press the call key twice. 5.
Introduction 1. Introduction With the Nokia Car Kit CK-200, you can make and answer calls hands free. You can also copy the contacts list from your two compatible mobile devices to the car kit and view the copied contacts on the builtin display to make calls through the connected device. The car kit comes with a wireless remote control that allows you to easily operate the car kit from a distance. You can use Bluetooth to connect the car kit to two compatible devices at the same time.
Introduction Download and install the Nokia car kit updater application from www.nokia.com/support to a compatible computer. Use a USB data cable that has a standard USB plug at one end and a micro USB plug at the other end, to connect the car kit display to a computer. The cable is sold separately. Open the updater application, and follow the displayed instructions. Keep the USB cable connected while the software is being updated.
Get started 2. Get started ■ Parts The car kit contains the following parts: 1 4 3 2 5 6 1. Main unit CK-200 with display 2. Mounting plate for main unit CK-200 3. Junction box RX-73 4. Remote control CU-13R with Navi wheel 5. Steering wheel mount for remote control CU-13R 6. CD that contains this guide In addition, the sales package includes cables and other parts that are needed when installing the car kit.
Get started ■ Remote control CU-13R You can use the remote control to operate the car kit. The device has a Navi wheel that you can turn or press. 1. Voice dialling / mute key 2. Switch key 3. Navi wheel 4. Call key 5. End key ■ Display and standby mode Display parts The display has the following parts: 1 1. Power key 2. Microphone 3.
Get started Rotate the display When the display is attached to the dashboard using the supplied mounting plate, you can rotate the display in the ball joint up to about 15 degrees left, right, up, or down. Do not try to force the display to rotate further. To adjust the angle of the mounting plate, loosen the screw at one end of the hinge on the plate, turn the plate in steps of 45 degrees, and tighten the screw. Information displayed in standby mode When you switch on the car kit, it enters standby mode.
Get started To enter a phone number manually or to use speed dialling, turn the wheel left. To search for a contact in the contacts list of the car kit, turn the wheel right. To view the last dialled numbers, press the call key. See also “Recent calls”, p. 22. Display indicators You have an active call. You have a call on hold. There is an incoming call. There is an outgoing call. You have missed calls in the device that is displayed above the indicator.
Get started ■ Insert the remote control battery The wireless remote control is powered by one CR2032 lithium coin cell battery. Replace the battery only with the same or equivalent type. 1. Slide the cover away from the device (1). 2. Insert the battery with the negative (-) terminal pointing towards the circuit board, and slide the cover back into place (2). To avoid short-circuits that may damage the battery, do not handle or store the battery with metal objects.
Get started ■ Switch the car kit on or off If you are not certain whether the ignition sense wire is connected or not, consult with the technician who installed the car kit. Before you use the car kit, make sure the display is firmly in place on the mounting plate. Switch on If the ignition sense wire is connected, the car kit switches on when you turn on the car engine. If the ignition sense wire is not connected, press the power key.
Get started After the language selection, you are asked to pair and connect the car kit to a compatible Bluetooth device. See “Pair and connect the car kit”, p. 16. ■ Pair and connect the car kit Before using the car kit, you must associate (pair) and connect it to a compatible mobile device that supports Bluetooth wireless technology. You can pair the car kit with up to eight devices and connect it to two devices that support the HFP Bluetooth profile at a time.
Get started To manually connect the car kit to a device (for example, after connection loss), make sure the device is switched on, and, in standby mode, select Menu > Settings > Connection > Connection manager and the device. Connect the car kit automatically You may be able to set your mobile device so that the car kit connects to it automatically. To activate this feature, modify the paired device settings in the Bluetooth menu of your device.
Basic use 3. Basic use ■ Copy contacts from connected devices You can copy contacts (names and phone numbers) from compatible mobile devices that you connect to the car kit. is displayed during copying. Copying may take several minutes, depending on the number of contacts. While the contacts are being copied, you cannot use the car kit. Manual copying If automatic copying is deactivated, you can copy the contacts manually.
Basic use You can only use the contacts of connected devices if you have copied them to the car kit. Make a call You can use the remote control to make calls only on the primary device. To make a call on the secondary device, set the device as primary, or make the call from that device. Instead of using the remote control, you can also make a call from the primary device. Use the device in the normal way for calling. To end the call (or cancel the call attempt), press the end key.
Basic use Voice dialling To activate voice dialling (if your device supports this feature with the car kit), press the voice dialling key when no call is in progress. Say the voice tag of the desired contact clearly. If the car kit is connected to two devices, voice dialling is activated on the primary device. For details on voice dialling, see the user guide of your device. Speed dialling Speed dialling is a quick way to call frequently used phone numbers.
Basic use ■ Adjust speaker volume To adjust the speaker volume during a call, turn the wheel. The selected volume is saved for the current device. To set the default volume for calls, see “Audio settings”, p. 26. To mute the speakers, set the volume to the lowest level. displayed. is ■ Manage two calls You can have two calls at the same time on one of the connected devices and handle the calls from the car kit. To answer a waiting call and end the active call, press the end key.
Basic use ■ Send tone strings To send a tone string such as a password (network service) during a call, select Call options > Send DTMF. Select the characters one by one. (To delete the previously entered character, press the end key.) To send the string, select , or press the call key.
Basic use When you select this menu, the car kit performs the function that you have specified for a short press of the My own key in the Nokia Accessory Setup Application. You can set the car kit to read out loud a new text message, call your favourite number, or reject a call and send a predefined text message. For details, read the help of the application.
Settings 4. Settings ■ Connection settings To manage Bluetooth connections, in standby mode, select Menu > Settings > Connection and from the following: • Connection manager — To pair and connect the car kit to a compatible device, select Pair new device. To connect the car kit to a previously paired device or disconnect a device, select the device from the list. • Multipoint connection — You can connect the car kit to two devices at the same time.
Settings ■ General settings In standby mode, select Menu > Settings > General and from the following: • Speed dials — Assign phone numbers to the speed dial numbers (1-9) for the connected device (if two devices connected, the primary device). Select an unassigned speed dial number. To assign a contact, select Contacts. To manually enter a number, select Number entry. To replace the contact that is assigned to a speed dial number, select the speed dial number and Replace.
Settings • Delete personal data — Delete contacts, speed dial numbers, or call lists from the car kit. • Restore factory settings — Reset the car kit settings to the default values. ■ Audio settings In standby mode, select Menu > Settings > Audio and from the following: • Audible menu — Set the car kit to play some display texts, such as the names of main menus. For information on available languages, go to www.nokia.com/support.
Troubleshooting 5. Troubleshooting ■ Reset the car kit The car kit doesn’t react to my actions. How can I reset it? Slide the display up from the mounting plate for 10 seconds. ■ Connection issues I can’t use Bluetooth to connect the car kit to my device. • Make sure the car kit is switched on and paired with your device. • Make sure Bluetooth is activated on your device, and authorise the car kit to connect to the device. ■ Audio issues My voice echoes on the other end of the line.
Troubleshooting • If the car kit is connected to an optional speaker, check that the car kit volume is set properly. • Make sure you have not accidentally muted the speaker volume. • Make sure your car radio is switched on. The car radio isn’t muted when I answer a call. Ask the technician who installed the car kit to make sure the car radio mute wire is properly connected. Not all cars have the mute wire. ■ Other issues The car kit doesn’t switch on when I turn on the car ignition.
Installation 6. Installation ■ Safety information Observe the following safety guidelines when installing the car kit. • Only a qualified service technician should install or service the car kit using the approved original Nokia parts supplied in the sales package. Faulty installation or service may be dangerous and may invalidate any warranty which may apply to the car kit.
Installation • When installing the parts of the car kit, make sure none of them interfere with or hinder the steering or braking systems or other controls or systems used in the operation of the vehicle (for example, airbags). Make sure the car kit and any of its components are not installed where you might come in contact with it in the event of an accident or collision.
Installation Open the updater application, and follow the displayed instructions. Keep the USB cable connected while the software is being updated. ■ Install the car kit in a vehicle This section describes how to install the car kit parts in a vehicle. The parts are explained in “Parts”, p. 10. When installing the parts of the car kit, make sure none of them interfere with or hinder the steering or braking systems or other controls or systems used in the operation of the vehicle (for example, airbags).
Installation Junction box RX-73 The junction box has the following connectors: 1 4 3 2 5 6 1. Connector for direct input cable CA-161 2. Connector for power cable CA-153P or power cable of ISO cable CA160 3. Connector for optional speaker (such as Nokia SP-3) or speaker cable of ISO cable CA-160 4. Connector for optional charging cable (such as CA-159) 5. Connector for display cable CA-165 6.
Installation Remote control CU-13R The remote control should be located so that it is within easy reach of the user. Do not mount the remote control within the head impact area. When installing the remote control, make sure it does not interfere with or hinder the steering or other controls or systems used in the operation of the vehicle (for example, airbags).
Installation 3. Pull the strap from the end to keep it securely in place (2). 2 1 4. Press the end of the strap downwards (3), and press the catch upwards (4). 5. Press the catch against the steering wheel until it locks into place (5). 3 5 4 6. Push the remote control into the holder (6). To release the remote control, push it from the bottom, through the opening in the holder. To detach the strap, pull the catch away from the steering wheel (7).
Installation Display You can attach the display to the dashboard using the supplied mounting plate. The display should be located so that it is clearly visible for the user and it can be easily rotated left, right, up, or down. When installing the display, make sure it does not interfere with or hinder the steering or braking systems or other controls or systems used in the operation of the vehicle (for example, airbags). Make sure the display cable reaches to the junction box.
Installation 2. Set the display to the appropriate position (2). 1 2 3. To adjust the angle of the mounting plate, loosen the screw at one end of the hinge on the plate, turn the plate (in steps of 45 degrees), and tighten the screw. To detach the display, slide it upwards from the mounting plate. ■ Installer settings The installer settings should only be modified by a qualified service technician.
Installation You can connect the car kit to a speaker with an impedance of at least 4 ohms. If the impedance is over 8 ohms, the output power is significantly lower than normal. With car specific wiring adapters, you can connect the car kit to the vehicle without any modification to the existing wiring. For availability, consult your service technician.
Installation • Connect the female connector of the ISO cable to the power and speaker connectors of the car wiring harness. • Check the permanent +12 V feed (red wire) and ignition feed (blue wire) on the junction box connector. If necessary, swap the configuration connectors "+12V battery" and "Ignition" of the ISO cable. Check the correct location of the mute signal for the car radio, and connect the configuration connector "Mute" to the corresponding socket (Mute1, Mute2, or Mute3).
Installation Installation using the power cable CA-153P and an external speaker In this setup, the junction box is connected to the car radio with the power cable CA-153P, and an optional external speaker is used for calls. CK-200 1. Connect the wires of the power cable CA-153P to the car as follows: • The black wire to the vehicle ground. • The red wire to the permanent 12 V. Always connect the supplied 2 A fuse to this line, close to the source.
Installation • The blue wire to the Ignition or ACC (accessory) line. Always connect the supplied 1 A fuse to this line, close to the source. 2. Connect the power cable to the respective connector on the junction box. 3. Connect the speaker (such as Nokia SP-3) to the respective connector on the junction box. 4. Connect the display to the respective connector on the junction box.
Installation Installation using the power cable CA-153P and direct input cable CA-161 In this setup, the junction box is connected to the car radio with the power cable CA-153P and the direct input cable CA-161, and the car radio speakers are used for calls. CK-200 1. Connect the wires of the power cable CA-153P to the car as follows: • The black wire to the vehicle ground. • The red wire to the permanent 12 V. Always connect the supplied 2 A fuse to this line, close to the source.
Installation • The blue wire to the Ignition or ACC (accessory) line. Always connect the supplied 1 A fuse to this line, close to the source. • The yellow wire to the car radio mute input. 2. Connect the direct input cable CA-161 to the respective connectors on the car radio and the junction box. 3. Connect the display to the respective connector on the junction box. In some cars, you may need to switch on the car radio to hear the call audio.
Installation Select the mounting location of the microphone carefully, to increase the quality of voice transmission. The best place to mount the microphone is close to the rear view mirror. Mount the microphone so that it points towards the driver’s mouth and is at least 1 metre (3 feet) from the car kit speaker, to avoid audio feedback. Make sure the microphone cable reaches to the junction box. Mount the microphone so that it is not exposed to air streams from the vents.
Care and maintenance Care and maintenance Your car kit is a product of superior design and craftmanship and should be treated with care. The following suggestions will help you protect your warranty coverage. • Keep the car kit dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will corrode electronic circuits. • Do not use or store the car kit in dusty, dirty areas. Its moving parts and electronic components can be damaged. • Do not attempt to open the car kit.
Additional safety information Additional safety information ■ Vehicles RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles such as electronic fuel injection systems, electronic antiskid (antilock) braking systems, electronic speed control systems, and air bag systems. For more information, check with the manufacturer or its representative of your vehicle or any equipment that has been added.
FCC/Industry Canada notice FCC/Industry Canada notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
