Installation Instructions

ManualsBrandsMicrosoft ManualsElectronicsBluetooth Wireless Car Kit

■ Introduction

This installation guide has been prepared to provide the basic information necessary to

install the car kit. This guide is not intended to be definitive, because different types and

models of vehicles will require different installation work. The information given is for

general guidance only.

The terms of warranty demand that this car kit be installed by an expe-

rienced installer and only genuine Nokia parts are used. An end user

should never attempt to install this car kit without professional assis-

tance as the installation requires special tools and knowledge.

All installations should take into account any special requirements of

the customer. However, should the customer require an installation

that is illegal or unsafe these facts must be pointed out to the cus-

tomer and a policy of non-compliance adopted.

Please refer to the phone's User's Guide for instructions on the phone's

operation, care and maintenance, including important safety informa-

tion.

Note: Read the warnings below before beginning the installation pro-

cedure.

Nokia Corporation 935XXXX issue 1

CK-IW IG_en1.fm Page 2 Tuesday, February 25, 2003 9:57 AM

Summary of content (9 pages)

PAGE 1
CK-IW IG_en1.fm Page 2 Tuesday, February 25, 2003 9:57 AM ■ Introduction This installation guide has been prepared to provide the basic information necessary to install the car kit. This guide is not intended to be definitive, because different types and models of vehicles will require different installation work. The information given is for general guidance only. The terms of warranty demand that this car kit be installed by an experienced installer and only genuine Nokia parts are used.
PAGE 2
CK-IW IG_en1.fm Page 3 Tuesday, February 25, 2003 9:57 AM ■ WARNINGS 1. ENSURE THAT THE VEHICLE'S BATTERY IS DISCONNECTED BEFORE YOU START THE INSTALLATION PROCEDURE, AND THAT IT REMAINS DISCONNECTED DURING THE PROCEDURE. 2. DO NOT SMOKE OR USE OPEN FLAMES WHEN WORKING NEAR THE VEHICLE'S FUEL SYSTEM. 3. ENSURE THAT THE VEHICLE'S ELECTRICAL CABLES, HYDRAULIC LINES, FUEL LINES, AND SAFETY EQUIPMENT ARE NOT DAMAGED DURING INSTALLATION. 4.
PAGE 3
CK-IW IG_en1.fm Page 4 Tuesday, February 25, 2003 9:57 AM ■ Unpacking Carefully unpack the equipment and ensure that the following items are present.
PAGE 4
CK-IW IG_en1.fm Page 5 Tuesday, February 25, 2003 9:57 AM ■ Wireless HF Unit HF-1W 1. Speaker 2. Mic 3. Remote 4. DC 5. Internal bluetooth antenna The HF-1W is used in a fixed car installation and it offers a wireless handsfree function and a wireless connection to compatible external devices. The HF-1W unit is attached to the vehicle interior using the mounting plate HH-1. HF-1W is secured to HH-1 with a screw (included with HH-1).
PAGE 5
CK-IW IG_en1.fm Page 6 Tuesday, February 25, 2003 9:57 AM ■ Remote Control Button CU-2 The Remote Control Button (CU-2) allows convenient operation of the phone. The speaker volume of the HF-1W can be controlled with a ring (rotary switch) in the CU-2. It is possible to receive a call or to dial by pressing a send/end push button in the CU-2 (also voice dialing).
PAGE 6
CK-IW IG_en1.fm Page 7 Tuesday, February 25, 2003 9:57 AM the surface where you attach this pad is dry and clean from dirt and dust. 3. Peel off the protective sheet (pad with rugged fabric) from the adhesive side and attach the pad to the bottom of the Remote Control Button. 4. Press the Remote Control Button against the pad in the car until button is firmly in place.. ■ HF Microphone HFM-8 The HF microphone should be installed according to the directions in the following pictures.
PAGE 7
CK-IW IG_en1.fm Page 8 Tuesday, February 25, 2003 9:57 AM ■ HF Speaker HFS-12 Install the HF speaker so that it is at least 3 ft./1 m away from the HFM-8 microphone to avoid acoustic feedback. Insert the HFS-12 plug into the SPEAKER socket and turn 90° clockwise to lock firmly in place. Under no circumstances should the HFS-12 prevent the driver from controlling or operating the vehicle in any way or observing traffic.
PAGE 8
CK-IW IG_en1.fm Page 9 Tuesday, February 25, 2003 9:57 AM ■ Ignition Sense IGNS The blue wire of the power cable CA-7P is used for the ignition sense feature. The use of ignition sense is recommended to prevent accidental draining of the car's battery and making the automatic connection to the phone. The wire is connected via a 1 A fuse to a 12 volt potential that is controlled by the ignition key.
PAGE 9
CK-IW IG_en1.fm Page 10 Tuesday, February 25, 2003 9:57 AM Press and hold the button until the indicator light starts to blink. When the blinking stops the car kit has been reset. For operating information refer to the CK-1W User's Guide or User's Guide supplied with the phone.