Nokia Bluetooth Headset BH-217 1 3 4 2 5 8 7 Issue 1 6
10 9 12 13 11 14
ENGLISH DECLARATION OF CONFORMITY Hereby, NOKIA CORPORATION declares that this BH-217 product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/phones/ declaration_of_conformity/. © 2010 Nokia. All rights reserved. Nokia, Nokia Connecting People and the Nokia Original Accessories logo are trademarks or registered trademarks of Nokia Corporation.
ENGLISH Introduction With the Nokia Bluetooth Headset BH-217, you can make and answer calls hands-free with your compatible mobile device. Read this user guide carefully before using the headset. Also, read the user guide for the device that you connect to the headset. This product may contain small parts. Keep them out of the reach of small children. Warning: The connector of the clip and car cradle may contain a small amount of nickel.
ENGLISH Get started 2. Connect the charger cable to the charger connector. To charge the headset when it is in the clip or car cradle, insert the lower end of the headset into the clip or car cradle (12), and connect the charger cable to the charger connector on the clip or cradle (13). Parts of the device are magnetic. Metallic The red indicator light is displayed materials may be attracted to the device. during charging.
ENGLISH The fully charged battery has power for up to 5 hours of talk time. When you keep the headset in the clip or car cradle, the fully charged battery has power for up to 3 months of standby time. When you use the headset without the clip or cradle, the standby time is up to 100 hours. To check the battery charge when the headset is not connected to a charger, press the multifunction key when the headset is connected to a mobile device. If the indicator light is green, the charge level is sufficient.
ENGLISH If the headset is not connected to a device within about 30 minutes, it switches off automatically. Pair and connect the headset Before using the headset, you must pair and connect it to a compatible device. You can pair the headset with up to eight devices, but you can connect it to a maximum of two devices at a time. To pair and connect the headset to a device: 1. Make sure your mobile device is switched on and the headset is off. 2.
ENGLISH When the headset is connected to at least one device and is ready for use, the blue indicator light flashes slowly. To manually connect the headset to the last used device, press and hold the multifunction key for about 2 seconds (when no other device is connected), or make the connection in the Bluetooth menu of the device. You may be able to set your device so that the headset connects to it automatically.
ENGLISH ear. Point the headset towards your mouth (10). Store in the clip or car cradle When you do not keep the headset on your ear, store it in the clip or car cradle. When the headset is in the clip or cradle, it is switched off. When you remove the headset from the clip or cradle, the headset automatically switches on. To place the headset into the clip or cradle, slide the headset into place (14). To remove the headset, slide it out. the airbag is not blocked or impaired in any way.
ENGLISH To activate voice dialling (if your mobile device supports this feature with the headset), when no call is in progress, press and hold the Adjust volume multifunction key for about 2 seconds The headset automatically adjusts the when the headset is not in the clip or volume according to ambient noise. To cradle. Proceed as described in the manually adjust the volume, use the user guide of the mobile device. volume controls of the connected To answer a call, remove the headset device.
ENGLISH Connect to two devices The headset can be connected to two devices at the same time. Pair and connect to two devices To pair the headset with two devices, switch on the headset, activate pairing mode, and pair it with the first device. Switch off the headset, activate pairing mode, and pair it with the second device. To connect the headset to the two devices, switch the headset off and back on.
ENGLISH and press and hold the multifunction key again for about 2 seconds. When you activate the prompts, the green indicator light flashes once. When you deactivate the prompts, the yellow light flashes once. In both cases, there is also an audible notification. hold the multifunction key for about 8 seconds. The headset beeps twice, the red and green indicator lights alternate, and the headset enters pairing mode.
ENGLISH If the battery has not been used for a long time, to begin charging, you may need to connect the charger, then disconnect and reconnect it. If the battery is completely discharged, it may take several minutes before the charging indicator is displayed. When your charger is not in use, unplug it from the electrical plug and the device. Do not leave a fully charged battery connected to a charger, as overcharging may shorten the battery's lifetime.
ENGLISH • • • • • • device gets wet, allow it to dry completely. Do not use or store the device in dusty or dirty areas. Moving parts and electronic components can be damaged. Do not store the device in high temperatures. High temperatures can shorten the life of the device, damage the battery, and warp or melt plastics. Do not store the device in cold temperatures. When the device warms to its normal temperature, moisture can form inside the device and damage electronic circuits.
ENGLISH waste. For more information on the environmental attributes of your device, see www.nokia.com/ecodeclaration. FCC/Industry Canada notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference; and 2. This device must accept any interference received, including interference that may cause undesired operation.
