Document1 8/7/98 12:44 PM OWNER’S MANUAL Page 1
Keys and the Display Switches phone on/off when you press and hold. Adjusts volume of the earphone or handsfree speaker. These keys perform the function shown on the display directly above them (e.g., here the keys are the “Menu” and “Memory” keys). “Dials” the number on display. With display clear, redials last number dialed. Ends a call.
Public System the phone uses (A, B, or both). None shown: Home area only. A call is in progress. Digital signaling is in use. The phone is roaming in a home type system. Flashing: roaming in a non-home type system. The phone is in alpha mode. You have a voice message. You have a text message. If flashing, text memory is full. Memory location, menu, or option number. Battery Charge Signal Strength These words change; they determine the function of the keys directly below them (e.g.
Connectors ➊➋ ➌ ➍ 1) For Rapid Cigarette Lighter Charger, Rapid Travel Charger, and Standard Travel Charger 2) Power connector for Desktop Charger CHH-2/CHH-2L 3) System and data connector for accessories, desktop chargers, and HF car kit 4) For external antenna iii
Table of Contents 1. Safety At A Glance ............................ 1 2. The Battery .......................................3 3. Basics ............................................... 7 Switching On or Off..............................................7 Signal Strength ....................................................7 Access Codes .....................................................7 4. Making and Receiving Calls .............9 Answering a Call ..................................................
8. Touch Tones .................................. 26 Sending Individual Touch Tones ........................ 26 Sending Strings of Touch Tones........................ 26 Touch Tone Settings in the Phone..................... 28 9. The Menu ....................................... 29 Summary of Menu Functions and Shortcuts ...... 30 Menu 01, Memory Functions ............................. 32 Menu 2, Messages............................................ 32 Menu 3, Call Settings ...................................
1. Safety At A Glance Read these simple guidelines before using your phone. Failure to comply with these guidelines may be dangerous or illegal. For more detailed safety information, see “For Your Safety” on page 54. Road Safety Comes First Don't use a hand-held phone while driving; park the vehicle first. Switch Off In Hospitals Switch off your phone when near medical equipment. Follow any regulations or rules in force. Switch Off On Aircraft Mobile phones can cause interference.
Using this Owner’s Manual The cellular phone described in this manual is approved for use in AMPS/TDMA networks. A number of features included in this guide are called Network Services. They are special services provided by cellular service providers. Before you can take advantage of any of these Network Services, you must subscribe to them through your home service provider. You can then activate these functions as described in this manual.
2. The Battery Your phone is powered by a rechargeable battery. Use only batteries approved by the phone manufacturer and recharge your battery only with the chargers approved by the manufacturer. New batteries must be charged with the phone off for at least 24 hours before initial use. A new battery’s full performance is achieved only after two or three complete charge and discharge cycles! Note: This chapter gives only the basics for battery usage.
Removing a battery Switch off the phone before removing the battery. 1. 2. 3. Charging a battery with Rapid Travel Charger (ACH-4U) 1) Connect the lead from the charger to the bottom of the phone. 2) Connect the charger to a standard 120V AC outlet. When the battery is charging, the battery indicator on the right side of the display scrolls. Allow the battery to completely charge. Charging is finished when the segments stop scrolling.
accessory available for your phone. The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time is noticeably shorter than normal, it is time to buy a new battery. Battery Charge The phone gives you a warning tone and the message BATTERY LOW when only a couple of minutes of talk time remain. When no more battery power remains, you get a Recharge Battery Tone and the message RECHARGE BATTERY. The phone switches itself off.
• Temperature extremes affect the ability of your battery to charge: it may require cooling or warming first. • Do not short circuit the battery. Accidental short circuiting can occur when a metallic object (e.g. coin, clip, or pen) causes direct connection of the + and terminals of the battery (metal strips on the back of the battery), for example when you carry a spare battery in your pocket or purse. Short circuiting the terminal may damage the battery or the connecting object.
3. Basics Switching On or Off • Press and hold ð for a second. When switching on, if your phone has an extendible antenna, extend the antenna fully. As with any other radio transmitting device, avoid unnecessary contact with the antenna when the phone is switched on. Push in the antenna when you are not using the phone. The phone carries out a short self-test and briefly displays the phone number in use. A Personal Reminder Note appears if you have programmed one with Menu 4 5.
Security Code (5 digits) • When the phone asks for the Security code:, enter it then press left (OK). ñ The Security Code comes with your phone and is required with some phone features. Keep it secret and in a safe place, separate from the phone. You cannot change the Security Code. If you need a new one, contact your dealer. The default is 12345. If you enter an incorrect security code (CODE ERROR) five times in a row, the phone won’t accept any entries for the next five minutes.
4. Making and Receiving Calls Answering a Call • Press any key (except then speak. ð, ô, ÷ or volume keys) í ô answers calls. Press With KEYS LOCKED, only to stop the ringing sound, without answering the call. Making a Call 1) Extend antenna fully. 2) Key in phone number. 3) Press í. Your phone can make and receive calls only when it is switched on and in the cellular network’s service area, and not set to Message Mode (see “Message Mode” on page 16).
Speed Dialing 1) Enter the memory location number (2 to 99). 2) Press í. The phone recalls the phone number from the memory, displays it briefly, then dials it. í í , the phone dials the number Note: If you press 1 stored with Menu 2 3, Set Voice Mailbox Number (see , the phone initiates an emerpage 15). If you press 9 gency call only if Menu 3 4, Emergency Key 9, is set to On. Last Number Redial 1) Clear display with 2) Press í. ù. Redialing any of the last 5 numbers í then W or V within a second.
Important! Official emergency numbers vary by location (e.g. 911 or other official emergency number). Only one emergency number is programmed into your phone to be dialed automatically by Emergency Key 9, which may not be the proper number in all circumstances. Emergency Key 9 dialing does not operate with KEYS LOCKED or when the phone is connected to a modem. Emergency Key 9 Note: Emergency Key 9 works only if it has been set to On in Menu 3 4! 1) Press 9 then í.
If an accessory with its own loudspeaker is connected to the phone, the volume keys select the volume for that accessory. Muting/Unmuting the phone’s microphone 1) Press and hold left ñ (Menu) for few seconds. 2) Press W to Mute or Unmute. 3) Press left ñ (OK). Muting and unmuting may be done only during an active call. Calling Line Identification If you have subscribed to and activated this network service, the phone displays the caller’s phone number if the system is able to identify it.
Key Lock • Press and hold ô, or press left ñ then ∗. Key Lock prevents accidental key presses (e.g. when the then ∗ to unlock phone is in your pocket). Press left the keypad. ñ Key Lock cannot be activated when the phone is connected to a car kit or a handsfree desktop charger. Note: With Keys Locked, calls may be possible to the ). Pressing 9 should emergency number 911 (911 also work, if Menu 3 4, Emergency Key 9, is set to ON. However, pressing and holding Emergency Key 9 does not function.
Calling Card Calls If you use the phone’s Calling Card storage feature (see “Menu 3 7, Calling Card” on page 33), you can use the method described below. You won’t need to enter Calling Card information every time you want to make a card call. Note: No physical credit cards are needed in order to direct the call charges to the credit card.
5. Voice and Text Messages Please check with your operator for the availability of message features. Voice Messages When you receive a voice message, the phone beeps, lights the voice message indicator ( ), and displays NEW VOICE MESSAGE. The phone shows the number of messages if there are more than one. To use the methods described below to call your voice mailbox, you must store your voice mailbox number in your phone, which is described in this section.
Message Mode • ñ Press left (Menu) #. (This also sets Message Mode off if it is on.) OR 1) Press left ñ (Menu) 3 8. 2) Press W to On. 3) Press left ñ (OK). With “Message Mode” set to On, you can receive Voice Mail Notification and Text Messages. You do not receive any incoming calls. The phone displays MSGS ONLY. The default setting is Off. “Message Mode” is a network service. Please check for the availability from your network operator.
To read messages immediately • With MESSAGE RECEIVED on display, press left ñ (Read). To read text messages any time ñ (Quit), then later: ñ (Menu) 2 2. 1) Press right 2) Press left 3) Press W to view the first message. 4) Scroll message(s) with W or V. The messages are shown in the order that they were received or stored. New messages are shown first, in their order of priority, then old messages, in their chronological order.
Read next shows the next message. Erase deletes the current message from memory. Lock/Unlock allows you to lock and unlock messages. When a new message arrives and the message memory is full, the new message automatically overrides old messages unless they are locked. Use Number lets you edit or call the number currently shown on the display. After selecting Use Number, you get the options Edit and Quit. To edit the number (e.g., add or remove digits), press Edit.
6. The Personal Directory You can store up to 100 numbers and associated names in your “Personal Directory”. Stored numbers may be up to 16 digits long. Stored names may be up to 16 characters long. The phone provides you with 8 extended number locations (any you choose) that allow the stored number to contain up to 30 digits in addition to the name. The identical name may be used only once in memory. REPLACE NAME? appears when you try to store a name already in memory.
When ABC is not displayed, you can use the ∗ key to enter these special characters: Press This Key: To Get This Special Character: óó +, links memory locations together óóó p, creates a pause óóóó w, causes the phone to wait for input Entering Names 1) Press ÷. 2) Press and release the key labeled with the letter you want until that letter appears. 3) For another letter on the same key, press ∗ in between letters or wait a few seconds. To erase a .
Storing Numbers and Names 1) Key in phone number. ñ (Memory). ñ (Store). 2) Press right 3) Press left 4) Key in name (optional). ñ (Store). Press left ñ (OK). 5) Press left 6) You can also enter another location number or scroll through available location numbers with W or V after the STORE IN LOCATION? prompt. To fast save 1) Key in phone number. 2) Press and hold right ñ (Memory).
To erase stored names and numbers With display empty, ñ (Memory). ñ (Store) then left ñ (Store) 1) Press right 2) Press left again. 3) Press W to name you want to erase, or key in name, to see numbers, then W. or press ÷ ñ (Erase). Press right ñ (Quit) instead of left ñ (Erase) if you change your mind. Press right ñ (Quit) again to 4) Press left exit the erase function. You may also use Menu 01 5 to erase.
3) Press right í ñ (Find). to dial the displayed number or displayed Press name’s number. To recall numbers by name 1) Press right ñ (Memory). 2) Key in name or its first few letters. 3) Press right ñ (Find). If you enter only the first letters of the name and there is more than one name beginning with these letters, press W or V until you see the name you want. Status of the Directory 1) Press left ñ (Menu) 01 6. 2) Press W to show the number of empty locations.
7. Temporary Lists & Call Timers The phone automatically stores the last 5 dialed numbers, and calling numbers of the last 5 answered and last 5 missed calls. Note: The phone displays the phone numbers of received and missed calls only if the cellular system is able to identify the caller and you have subscribed to this service. To view Dialed Numbers 1) With display empty, press í. 2) Press W or V within a second.
The top right corner of the display shows you the location number (U0-U4) of the calling phone numbers of the 5 to most recent calls you have not answered. Press view associated names, if available. You may also use Menu 01 3, Missed Calls. ÷ To clear temporary lists • Press left ñ (Menu) 01 4. This clears Dialed Numbers, Received Calls, and Missed Calls. You cannot undo this operation so be careful! Call Timers 1) Press left ñ (Menu) 01 7. 2) Press W to the timer you want to see.
8. Touch Tones Your phone is a “Touch Tone” phone, meaning that it creates certain sounds when you press the keys. These sounds can be used for many automated, over-the-phone services such as checking your bank balance, using your voice mailbox options, and even checking airplane arrival and departure times. Touch Tones are called “DTMF” (Dual Tone Multifrequency) tones in the phone. Sending Individual Touch Tones • Press keys during call. Touch Tones can be used only when a call is active.
To store a Touch Tone string Store Touch Tone strings the same way as you store phone numbers. For example, you could store a voice mail number in the personal directory. To store Touch Tone strings with a phone number 1) Key in the phone number. 2) Press ∗∗∗ (p) or ∗∗∗∗ (w). 3) Key in the Touch Tone string. 4) Store the number in the normal way. ∗∗∗ creates a “p” (pause) character. When you recall this í , the number sequence from memory and press phone dials the phone number, pauses 2.
∗∗ creates a “+” (link to another memory location). When you recall this number sequence from memory and press , the phone dials the phone number, then displays digits stored in the memory location you have entered. Press left (DTMF) to send them. í ñ Entering only a “+” at the end of a stored number causes the phone to prompt you for a memory location after the call is connected. The phone expects a memory location after the “+” character. Enter a location number and press left (OK).
9. The Menu The phone’s menus and submenus give access to most of the phone’s functions. Menu guidelines 1) Press left ñ (Menu) to enter the menus. 2) Press W and V to step through menus, submenus, and options. 3) ÷ gives help text on menus and submenus and goes to the next screen of help text if there are several. ñ (Quit) to go back one level. ù exits the menu facility without making changes. 4) Press right 5) Scrolling through the menus 1) Press left ñ (Menu). 2) Press W or V to menu you want.
Summary of Menu Functions and Shortcuts Memory Functions Menu 01 1 2 3 4 5 6 7 Dialed Calls Received Calls Missed Calls Clear All Call Lists Memory Erase Options Memory Status Call Timers Messages Menu 2 1 Listen to Voice Messages 2 Read Messages 3 Set Voice Mailbox Number Call Settings Menu 3 1 2 3 4 5 6 7 8 Ringing Volume Ringing Tone One-Touch Dialing Emergency Key 9 Automatic Redial Automatic Answer Calling Card Message Mode Phone Settings Menu 4 1 2 3 4 5 6 Countdown Timer 7 Restore Settings 8
System Search Menu 7 Menu 6 Note: The items in Menu 6 shown in italics are visible ONLY when activated with Menu 6 7! Selects which cellular system to use. NAM Selection Menu 8 Network Services Some of the menu functions are network services. These functions can be utilized only if provided by your cellular network. To make use of a Number Editor Menu 9 network service, you must first subscribe to it. For availAllows editing of the currently-displayed number.
Menu 01, Memory Functions See “The Personal Directory” on page 19 and “Temporary Lists & Call Timers” on page 24 for descriptions of the items in Menu 01. Menu 2, Messages See “Voice and Text Messages” on page 15 for descriptions of these menu items. Menu 3, Call Settings Menu 3 1, Ringing Volume You hear each ringing level as you scroll through the volume levels.
Menu 3 5, Automatic Redial When this is on, your phone redials the number you are trying to call (if the network is busy, indicated by a fast busy to end the call attempts. tone) up to 10 times. Press The phone beeps when the call goes through. ô Menu 3 6, Automatic Answer When the phone is connected to the headset or the handsfree facility of the car kit, you can set the phone to answer a call automatically after one ring. The car kit must be equipped with the ignition sense option.
5) The phone then prompts you for other information, such as Access number and Card number. Enter this information at each prompt and press left (OK). ñ ÷ 6) You can enter the calling card name by pressing when the phone prompts you for the access number or card number. The phone will then prompt you for the card name. Enter it and press left (OK). ñ To change stored calling card information (such as your card number), go through these steps, but use key to erase already stored information.
Menu 4 3, Manual DTMF Tones Menu 4 4, Auto DTMF Length See “Touch Tones” on page 26 for descriptions of these items. Menu 4 5, Personal Reminder Note 1) Press left ñ (Menu) 4 5. 2) Key in a new message or edit the existing one. 3) Press left ñ (Option). 4) Press W to Store or Erase. 5) Press left ñ (OK). The Personal Reminder Note displays when the phone is switched on. The maximum length is 30 characters. Characters you key in are added to the left of the cursor.
An incoming call overrides the timer alarm. After you have completed the call, COUNTDOWN COMPLETED appears, but the phone does not sound an alarm. To stop the timer before it alarms • Follow the steps above, but key in 0000 at Set timer:. To clear the alarm when it is sounding • Press any key except ð. Menu 4 7, Restore Settings You can reset the settings of certain menu functions to factory defaults (as in a new telephone). Note: The memory, timers, counters, and language are not reset.
Menu 5, Security Options Most of the phone’s security features require a five-digit security code, which is normally supplied with your phone. The default is 12345. If you forget the security code, contact your dealer. Since this code allows access to all the operations of the phone, store it in a safe place, separately from the phone. Menu 5 1, Automatic Phone Lock When you turn this on, the phone’s lock becomes active after you switch the phone off and back on.
Menu 5 3, Restrict Calls You can prevent the phone from dialing a number or receiving a call. When calls are restricted, calls may be possible to the emergency number programmed into your phone (e.g. 911 or other official emergency numbers). Menu 5 3 1, Outgoing Calls Allowed means that all calls can be made as usual. Blocked means that no calls can be made. Limited means that calls can be made only to phone numbers stored in certain personal directory locations. You are prompted for a FROM: and TO: value.
In each cellular service area there are usually two cellular operators operating public systems of type “A” or “B”. One of the public systems (A or B) is your home system (depending on your operator) but your phone can work with both types of systems. With Menu 7, you can select the type of system the phone should use. (If you have registered with several operators, use Menu 8, NAM SELECT, to select a NAM. This determines which phone number and “home system” the phone uses.
Note: The ESN for your cellular phone is printed under the battery pack on the back of the phone. Menu 6 2, Dual mode Select You can set the phone to work in AMPS (Analog) and/ or TDMA (Digital) networks. The network can always override your setting, however. When the phone is in dual mode (Ana.& Dig.), the cellular network automatically selects the right mode. The phone automatically returns to dualmode (Ana.& Dig.) when you switch the phone off and back on.
Forward All Calls (Menu 6 4 1) forwards all incoming calls. Forward If Busy (Menu 6 4 2) forwards calls only when you are on the phone. Forward If Not Answered (Menu 6 4 3) forwards calls if you don’t answer. Forward If Out of Reach (Menu 6 4 4) forwards calls if you are out of the serving cellular network. Cancel All Forwarding (Menu 6 4 5) cancels all currently-active forwarding options. Menu 6 5, Call Waiting This appears on the menu only if activated with Menu 6 7. 1) Press left ñ (Menu) 6 5.
Note: This feature functions only in systems equipped with Calling Number Identification. Contact your network operator to see if this is available. Menu 6 7, Network Feature Setting Call Forwarding, Call Waiting, and Send Own Number are services available through your network operator. When you subscribe to any of these services, your operator or dealer gives you a separate code that you use to activate and deactivate each service. Menu 6 7 lets you store all the codes you use in your phone.
Menu 7, System Search Your phone works in Public Systems (such as your Home System), and in Private Systems (if supported by the network). With Menu 7, you choose how the phone selects a network to use. The default is Automatic, which means the phone automatically searches for networks available to you and chooses the appropriate one. Every time you switch on the phone, it resets this to Automatic. (Note that it chooses which Public system to use based on the choice you make in Menu 6 1, Public Systems).
NAM, which contains unique data for you such as your phone number, home service area, and A-key. Only one NAM is in effect at a time. When you select a NAM (phone number), you are also selecting your Home System. The first phone number displayed with this menu is the phone number in use. Note: You need at least one active number to make calls. You cannot change from one NAM to another during a call. Menu 9, Number Editor The number you want to edit must be on the display. ñ (Menu) 9.
ô When the phone starts to alert, you can press to mute the ringing tone. The phone continues to alert silently by flashing the lights and the text CALL on the display. When Beep Once, Vibrate or Silent has been chosen, the phone displays SILENT. Call related tones like message received or voice mail indication beeps become shorter with one of the above options selected. When Silent has been chosen, Automatic Answer (Menu 3 6) does not work.
10. Data and Fax Calls The phone can send or receive data when it is connected to a compatible data terminal (such as a fax machine or PC) through a data adapter. See the documentation for the data adapter and terminal. Only analog data can be sent and received. The phone recognizes the type of the connected terminal automatically. For instance, if a fax machine is connected to the phone, the phone makes a fax call.
To receive a fax call 1) Check that the data terminal is properly installed. í to answer the call. OR, if you know this is 2) Press an incoming fax, you can answer the call from the fax machine’s keypad. 3) After the transmission, end the call from the fax . machine’s keypad.
11. Accessories In addition to the accessories that were included in your phone’s sales package, you may also find a separate full color accessories brochure. You can select from a wide range of Nokia accessories to accommodate your specific communication needs. For availability, please check with your local dealer. A few practical rules for accessory operation • Keep all accessories out of the reach of small children.
Also see “The Battery” on page 3 and “Important Battery Information” on page 5. Approximate battery operation times Battery Charging Time (BBH-1S) Slim 600 mAh NiMH (ACH-3U/ AEC3518) 270 min. (ACH-4U) 60 min. (BBT-1XV) Vibrating 600 mAh NiMH (ACH-3U/ AEC3518)) 270 min. (ACH-4U) 60 min. (BBH-1SF) Extended Slim 800 mAh NiMH (ACH-3U/ AEC3518) 270 min. (ACH-4U) 60 min. (BBH-2H) Ultra Extended 1100 mAh NiCd (ACH-3U/ AEC3518)) 540 min. (ACH-4U) 120 min. Up to 2 hrs. 30 min.
NiMH NiCd CONTAINS: NICKEL METAL HYDRIDE AND/OR NICKEL CADMIUM BATTERY. MUST BE RECYCLED OR DISPOSED OF PROPERLY. MUST NOT BE DISPOSED OF IN MUNICIPAL WASTE. Chargers It is recommended that you allow your battery to fully discharge before you recharge it. Batteries last longer and perform better if allowed to discharge fully at least once a week. Standard Travel Charger (ACH-3U) This charger can be used with all battery options.
Rapid Cigarette Lighter Charger (LCH-2) You can charge the phone battery from your vehicle battery by using the Rapid Cigarette Lighter Charger (LCH-2). You can also use the charger with stands (CHH-2) and CHH-2L (described below). Calls are possible during charging. A green light indicates the charger is ready for charging (when not charging) or finished charging (if it has been charging). A red light indicates charging.
Connect either the Rapid Travel Charger (ACH-4U) or the Rapid Cigarette Lighter Charger (LCH-2) to the stand, and then plug the Rapid Travel Charger or Rapid Cigarette Lighter Charger into a wall outlet or vehicle respectively. Place the phone and/or the spare battery in the stand. To discharge the spare battery, press the blue button on the stand. When the battery is totally discharged, recharging starts automatically.
12. Care and Maintenance Your phone is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfill the warranty obligations and to enjoy this product for many years. • Keep the phone and all its parts and accessories out of small childrens’ reach. • Keep the phone dry. Precipitation, humidity and liquids contain minerals that will corrode electronic circuits. • Do not use or store the phone in dusty, dirty areas.
13. For Your Safety Traffic Safety Do not use a hand-held telephone while driving a vehicle. If using a hand-held telephone park the vehicle before conversing. Always secure the phone in its holder; do not place the phone on the passenger seat or where it can break loose in a collision or sudden stop. The use of an alert device to operate a vehicle’s lights or horn on public roads is not permitted.
Only qualified personnel should install or service the phone in a vehicle. Faulty installation or service may be dangerous and may invalidate the warranty. Electronic fuel injection systems, electronic anti-skid braking systems, electronic cruise control systems and other electronic systems can malfunction due to the lack of protection from radio signals. Check regularly that all cellular phone equipment in a vehicle is mounted and operating properly. Switch off your cellular phone when in an aircraft.
Emergency calls on your phone If certain features are in use (Keyguard, Locking, Call Restricting, etc.), you may first need to turn those features off before you can make an emergency call. Consult this document and your local cellular service provider. When making an emergency call, remember to give all the necessary information as accurately as possible.
14. Technical Data Cellular System TDMA and AMPS Weight 7.9 oz (224g) with 600mAh NiMH battery Capacity 169 cc Frequency Range 824.010 - 848.970 MHz (TX) 869.010 - 893.970 MHz (RX) Transmitter Output Power 0.
NOKIA One-Year Limited Warranty Nokia Mobile Phones, Inc. (“NMPI”) warrants that this cellular phone (“Product") is free from defects in material and workmanship, according to the following terms and conditions: 1. The limited warranty for the Product extends for ONE (1) year beginning on the date of purchase of the Product. 2. The limited warranty extends only to the original consumer purchaser (“Consumer”) of the Product and is not assignable or transferable to any subsequent purchaser/end user. 3.
d) The defect or damage was caused by the defective function of the cellular system, or by inadequate signal reception by the external antenna. 8. If a problem develops during the limited warranty period, the Consumer should take the following step-by-step procedure: a) The Consumer shall return the Product to the place of purchase for repair or replacement processing.
11. Some states do not allow limitation of how long an implied warranty lasts, so the above limitation may not apply to you (the Consumer). Some states do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusions may not apply to you (the Consumer). This limited warranty gives you specific legal rights and you may also have other rights which vary from state to state. 12.
NOTES 61
