DESCRIPTION OF KEYS Use the phone keys as follows: CALL INDICATOR LIGHT PWR Press and hold to switch the phone on/off. SIDE BUTTON Upper button increases and lower button decreases volume. ▲▼ Scroll the menu and memories. Press and hold for continual scrolling. F CLR Deletes characters and clears the display. Soft keys. Function changes according to the operation in progress. SND “Dials” the number on display. With display clear, redials last number dialed.
Contents 1. Important Safety Information..........................1 Traffic Safety...........................................................1 Operating Environment ...........................................1 Emergency Calls ....................................................2 Using this Owner’s Manual .....................................3 2. The Display and Connectors...........................5 3. The Battery ......................................................7 Installing a battery..................
8. Temporary Lists and Call Timers .................25 To view Dialed Numbers .......................................25 To view Last Received Calls ..................................25 To view Missed Calls.............................................25 Notepad ...............................................................26 Call Timers ...........................................................26 9. Touch Tones....................................................27 Sending Individual Touch Tones ...........
1. Important Safety Information Traffic Safety Do not use a hand-held telephone while driving a vehicle. If using a hand-held telephone park the vehicle before conversing. Always secure the phone in its holder; do not place the phone on the passenger seat or where it can break loose in a collision or sudden stop. The use of an alert device to operate a vehicle’s lights or horn on public roads is not permitted.
Only qualified personnel should install or service the phone in a vehicle. Faulty installation or service may be dangerous and may invalidate the warranty. Electronic fuel injection systems, electronic anti-skid braking systems, electronic cruise control systems and other electronic systems can malfunction due to the lack of protection from radio signals. Check regularly that all cellular phone equipment in a vehicle is mounted and operating properly. Switch off your cellular phone when in an aircraft.
If certain features are in use (Keyguard, Locking, Call Restricting, etc.), you may first need to turn those features off before you can make an emergency call. Consult this document and your local cellular service provider. →If the phone is not on, switch it on →press and hold to clear display →key in emergency number for your present location (e.g. 911 or other official emergency number) →press Emergency calling C U Note: Emergency numbers vary by location.
FCC/INDUSTRY CANADA NOTICE Your phone may cause TV or radio interference (e.g. when using telephone in close proximity of receiving equipment). The FCC/Industry Canada can require you to stop using your telephone if such interference cannot be eliminated. If you need assistance, contact your local dealer. This device complies with parts 15 and 68 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference.
2. The Display and Connectors The Disp lay A or B: Network the phone uses A - A system only B - B system only AB - Both systems No indicator: Home area only A call is in progress (In Use indicator). D The phone is using a digital channel. The phone is in a network other than your home network (roaming). Shown continuously: roaming in a home-type system. Flashing: roaming in a non-home-type system. ABC The phone is in alpha mode. A voice message is waiting. Steady: You have received a text message.
Connectors ➊➋ ➌ ➍ Ê For Fast Cigarette Lighter Charger, Fast Travel Charger, and Standard Travel Charger Ë Power connector for Desktop Charger CHH-2/CHH-2L Ì System and data connector for accessories, desktop chargers, and HF car kit Í For external antenna 6
3. The Battery Your phone is powered by a rechargeable battery. Use only batteries approved by the phone manufacturer and recharge your battery only with the chargers approved by the manufacturer. A new battery’s full performance is achieved only after two or three complete charge and discharge cycles! Note: This chapter gives only the basics for battery usage. See “Accessories” for more information on chargers and other accessories.
Charging a battery with Fast Travel Charger (ACH-4U) Ê Connect the lead from the charger to the bottom of the phone. Ë Connect the charger to a standard 120V AC outlet. When the battery is charging, the battery indicator on the right side of the display scrolls. Allow the battery to completely charge. Charging is finished when the segments stop scrolling. The charging times depend on the type of the battery and the charger used. See the “Accessories” chapter for details.
Note: In some vehicles, the ignition must be on in order to charge the phone with the cigarette lighter adapter. If the message NOT CHARGING is displayed, charging is suspended. Check that the battery is not overheated (over 104°F/40°C), too cold, or connected to a non-approved charging device. Wait for a while, connect the charger to the phone again and retry. If charging still fails, contact qualified service personnel.
Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, reduces the capacity and lifetime of the battery. Always try to keep the battery between 59°F and 77°F (15°C and 25°C). A phone with a hot or cold battery may temporarily not work, even if the battery is fully charged. NiMH battery performance is particularly limited in temperatures below 14°F (-10°C). The battery is a sealed unit with no serviceable parts. Do not attempt to open the case.
4. Basics Switching On or Off Press and hold a second. P for When switching on, if your phone has an extendible antenna, extend the antenna fully. As with any other radio transmitting device, avoid unnecessary contact with the antenna when the phone is switched on. Push in the antenna when you are not using the phone. The phone carries out a short self-test and briefly displays the phone number in use. A Personal Reminder Note appears if you have programmed one with Menu 4 5.
Note: Avoid using access codes similar to emergency numbers such as 911 to prevent accidental dialing of the emergency number. Enter the 5-digit code then left (OK) at Security Code: prompt. Security Code (5 digits) F The Security Code comes with your phone and is required with some phone features. Keep it secret and in a safe place, separate from the phone. You cannot change the Security Code. If you need a new one, contact your dealer. The default is 12345.
5. Making and Receiving Calls →Press any key (except , , or volume keys) then speak Answering a Call PEA U If Keyguard is on, only answers calls. Pressing stops the ringing sound, but doesn’t answer the call. E ÕExtend antenna fully ÕKey in phone number ÕU Making a Call Your phone can make and receive calls only when it is switched on and in the cellular network’s service area. NO SERVICE means that you are probably outside the cellular service area. No calls can be placed or received.
U you press 9 , the phone initiates an emergency call only if Menu 3 4, Emergency Key 9, is set On! Last Number Redial Redialing any of the last 10 numbers U ÕClear display with C ÕU ÕU then ▼ or ▲ within a second ÕOnce you see the number you want, press U to dial it. Note: After , you must press ▼ or ▲ within a second to scroll through the last 10 dialed numbers. Otherwise, the phone automatically dials the most recently dialed number.
U →Press 9 then OR: →Press and hold 9 for more than 3 seconds Emergency Key 9 The phone dials the preprogrammed emergency number (e.g. 911) with either of these dialing methods. You can also dial an emergency number as usual by keying in the whole emergency number then . U Note: Pressing and holding Emergency Key 9 to dial an emergency call does not function when Keyguard is in use or when the phone is connected to a modem. (See “Keyguard” later in this chapter for more information on Keyguard.
Calling Line Identification If you have subscribed to and activated this network service, the phone displays the caller’s phone number if the system is able to identify it. The phone displays the caller’s name if you have stored that caller’s name and number, and the person calls you from the number you have stored. CALL or NO ID CALL displays when the number is not available. PRIVATE ID CALL displays when the caller has prevented the number from being shown.
When placing an emergency call, the emergency number will be displayed only after you have keyed in all its digits. After the emergency call, Keyguard becomes active again. U Answering a call with Press . Keyguard active During the call the keypad remains unlocked which lets you operate the phone as usual. After you end the call, Keyguard becomes active again. Call Waiting With Call Waiting, the active call is put on hold as you answer the waiting (incoming) call.
6. Voice and Text Messages Please check with your operator for the availability of message features. Voice Messages When you receive a voice message, the phone beeps, lights the voice message indicator ( ), and displays NEW VOICE MESSAGE. The phone shows the number of messages if there are more than one. To use the methods described below to call your voice mailbox, you must store your voice mailbox number in your phone, which is described in this section.
Also, to use text messaging, you must have the phone number of your message service center available. The phone can store up to 30 text messages, with a maximum of about 1,900 characters for all messages combined. Contact your network operator for details about the text messaging service and the maximum number of characters allowed in a message. The network may have its own default message that is displayed when the phone is in the network coverage area.
EMERGENCY indicates that the message received was marked “emergency” by the sender. LOCKED indicates that you have locked the message. It will not be overwritten even if there is no more space in memory and there is an attempt to deliver a new message to your phone. With message on screen, press left (Option) ▼ to option you want left (OK) The Option soft key Õ F Õ Õ F Read next shows the next message. Erase deletes the current message from memory. Lock/Unlock allows you to lock and unlock messages.
7. The Personal Directory You can store up to 100 numbers and associated names in your “Personal Directory”. Stored numbers may be up to 16 digits long. Stored names may be up to 16 characters long. The phone provides you with 8 extended number locations (any you choose) that allow the stored number to contain up to 30 digits in addition to the name. The identical name may be used only once in memory. REPLACE NAME? appears when you try to store a name already in memory.
When ABC is not displayed, you can use the ∗ key to enter these special characters: ∗∗ +, links memory locations ∗∗∗ p, creates a pause ∗∗∗∗ w, causes the phone to wait for input ÕA ÕPress and release the Entering Names key labeled with the letter you want until that letter appears for another letter on the same key, press ∗ in between letters or wait a few seconds Õ Example Name: Lisa Press this A 555 press and hold 4, then 4 4 7777 2 For this effect alpha mode L I (lower case) s a ÕKey in phone nu
To add a name to a stored phone number ÕRecall stored phone number ÕA then key in name Õright F (Memory) then left F (Store) ÕAt STORE IN LOCATION? enter recalled location number left (OK) then left (OK) again at REPLACE? Õ F F ÕRecall stored number ÕC repeatedly to erase number Õkey in new number Õright F (Memory) Õleft F (Store) then left F (OK) again at To change the number stored with a name REPLACE? To erase stored names and With display empty, numbers right (Memory) left (Store) then left (Stor
Recalling Stored Numbers With display empty, press ▼ or ▲. Press ▼ or ▲ repeatedly to scroll through stored numbers. Press to see corresponding names. A Recalling Stored Names With display empty, press then ▼ or ▲. A Press ▼ or ▲ repeatedly to scroll through stored names. Press to dial the displayed name’s number. U ÕKey in location number Õright F (Memory) Õright F (Find) To recall numbers by memory location U Press to dial the displayed number or displayed name’s number.
8. Temporary Lists and Call Timers The phone automatically stores the last 10 dialed numbers, numbers of the last 10 answered calls, and numbers of the last 10 missed calls. It also gives you 10 temporary storage spaces, in a “Notepad”. Note: The phone displays the phone numbers of received and missed calls only if the cellular system is able to identify the caller.
Notepad The Notepad is “temporary storage” for up to 10 numbers. ÕStore number as To store numbers and names in Notepad normal, but at STORE IN LOCATION, press # left (OK) Õ F See “The Personal Directory” chapter for details on storing numbers. # then ▼ or ▲ To see numbers and names in Notepad The top right corner of the display shows the location number of the Notepad (o0 - o9).
9. Touch Tones Your phone is a “Touch Tone” phone, meaning that it creates certain sounds when you press the keys. These sounds can be used for many automated, overthe-phone services such as checking your bank balance, using your voice mailbox options, and even checking airplane arrival and departure times. Touch Tones are called “DTMF” (Dual Tone Multifrequency) tones in the phone. Sending Individual Touch Tones Press keys during call. Touch Tones can be used only when a call is active.
For example, you could store your bank account number in the personal directory. ÕKey in the phone number Õpress ∗∗∗ (p) or ∗∗∗∗ (w) Õkey in the Touch Tone string Õstore the number in To store Touch Tone strings with a phone number the normal way ∗∗∗ creates a “p” (pause) character. When you recall this number sequence from memory and press , the phone dials the phone number, pauses 2.5 seconds, then sends the DTMF digits. You can add as many “p” characters as you need.
Entering only a “+” at the end of a stored number causes the phone to prompt you for a memory location after the call is connected. The phone expects a memory location after the “+” character. Enter a location number and press left (OK) to send the contents of that memory location as Touch Tones. F Touch Tone Settings in the Phone Your phone’s Touch Tone settings are Menu 4 3, Manual DTMF Tones, and Menu 4 4, Auto DTMF Length.
10. The Menu The phone’s menus and submenus allow you to tailor the phone to suit your tastes.
Summary Of Menu Functions MEMORY FUNCTIONS Dialed Calls 01 1 Received Calls 01 2 Menu 01 Missed Calls 01 3 Clear All Call Lists 01 4 Memory Erase Options 01 5 Memory Status 01 6 Call Timers 01 7 MESSAGES Menu 2 Listen to Voice Messages 2 1 Read Messages 2 2 Set Voice Mailbox Number 2 3 CALL SETTINGS Menu 3 Ringing Volume 3 1 Ringing Tone 3 2 One-Touch Dialing 3 3 Emergency Key 9 3 4 Automatic Redial 3 5 Automatic Answer 3 6 Calling Card 3 7 Pager Mode 3 8 PHONE SETTINGS Menu 4 Lights 4 1 Keypad Tones 4
NETWORK SERVICES Menu 6 (see note below) Dual Mode Selection 6 1 Voice Privacy 6 2 Call Forwarding 6 3 Forward All Calls 6 3 1 Forward If Busy 6 3 2 Forward If Not Answered 6 3 3 Forward If Out of Reach 6 3 4 Call Waiting 6 4 Selective Call Acceptance 6 5 Allowed Numbers List 6 5 1 Blocked Numbers List 6 5 2 Send Own Number 6 6 Network Feature Setting 6 7 SYSTEM SELECTION Menu 7 Selects which cellular system to use. NAM SELECTION Menu 8 Selects the phone’s system and current phone number.
Menu 3, Call Settings Menu 3 1, Ringing Volume You hear each ringing level as you scroll through the volume levels. When the phone is connected to a handsfree desktop charger, handsfree car kit, or headset, the ringing volume can be set separately for those accessories with this menu. Menu 3 2, Ringing Tone The phone plays a sample of each pattern as you scroll. Note: The ringing tone is the same for all accessories.
ÕLeft F (Menu) 3 7 Õ▼ to the card you want then left F (OK) Õkey in security code at Security code: then left F (OK) Õkey in access Menu 3 7, Calling Card To store a calling card number at Access Number: press then key in card name (optional) left (OK) key in card number at Card ID Code: then left (OK) Õ A Õ F Õ F To change stored calling card information (such as your card number), go through these steps, but use the key to erase already stored information.
Menu 4, Phone Settings Menu 4 1, Lights With lights on, the keypad lights come on when you press a key or have an incoming call, and go off 15 seconds later. When the phone is connected to a car kit, desktop charger, or cigarette lighter charger, the lights are on permanently when this setting is ON; when this setting is OFF, the lights come on when you press a key or have an incoming call, and go off 15 seconds later.
Press ▼ or ▲ to move the cursor right or left. Store stores the new or edited note for later use. The note is displayed each time you switch the phone on. Erase removes the note from the display and from the memory. Next time you switch the phone on, the stored note displays. Once you have read the note, press left (Keep) to save it or right (Erase) to delete it. It displays each time you turn the phone on until you erase it.
Emergency Key 9 Off Automatic Redial Off Automatic Answer Off Pager Mode Off Lights On Keypad Tones Level 2 Manual DTMF Tones Continuous Auto DTMF Length Long Menu List Complete Automatic Phone Lock Off Lock Code 1234 Dual Mode Selection Ana. & Dig. Voice Privacy Off Ringing Options Ring Menu 4 8, Menu List This function lets you choose either a shortened or complete menu.
When the phone is locked, calls may be possible to the emergency number programmed into your phone (e.g. 911 or other official emergency number) including calls with the Emergency Key 9. Also, you may call the number stored in location 100. U To answer a call with Press . Auto Lock on: To call the number in ▼ or ▲ then location 100 with Auto Lock on: Note: To unlock the phone permanently after locking it, you need to enter this function and select the AUTO LOCK OFF option.
Menu 5 3 2, International Calls Allowed means you can make international calls (i.e., calls beginning with the international prefix preprogrammed in your phone). Blocked means you can’t make international calls with the phone. Menu 5 3 3, Incoming Calls Allowed means you can receive all calls. Blocked means you can receive no calls. Menu 5 4, Hide Memory This function lets you hide phone numbers in your personal directory.
Menu 6 2, Voice Privacy You may set this to On or Off. Voice Privacy On encrypts the voice channel only in networks with digital service. If you have this feature on and voice privacy becomes inactive for any reason the phone displays VOICE PRIVACY INACTIVE and beeps. Check for availability of this function from your network operator.
ÕLeft F (Menu) 6 5 Õ▼ to Allowed Menu 6 5, Selective Call Acceptance Numbers List or Blocked This appears on the menu only Numbers List ▼ to Activate, if activated with Menu 6 7 Õ Deactivate, or Edit Õleft F (OK) With this, you can program the network to screen incoming calls. The caller’s phone number is compared to the list you select and the call is then either rejected or allowed. Allowed Numbers List allows calls when the incoming caller’s number matches one on the allowed numbers list.
If you do not make a selection, the phone uses the default network setting, which is always active when you switch on your phone. Check with your network operator to find out the network default. Menu 6 7, Network Feature Setting Call Forwarding, Call Waiting, Selective Call Acceptance, and Send Own Number are services available through your network operator or dealer.
Menu 7, System Select In each cellular service area there are usually two cellular operators operating public systems of type “A” or “B”. One of the public systems (A or B) is your home system (depending on your operator) but your phone can work with both types of systems. With Menu 7, you can select the type of system the phone should use. If you have registered with several operators, use Menu 8, NAM Select, to select the current home system.
Roaming Indicators When the phone begins roaming, it beeps, displays ROAMING, and lights the roaming indicator ( ). For a description of the two states of the roaming indicator, see “The Display and Connectors” chapter. Some cellular systems can recognize a roaming phone automatically. In other systems, you must contact the cellular operator before the system can recognize the phone. You will need to give your phone number, your phone’s ESN (electronic serial number), and how you plan to pay for your calls.
Menu 9, Number Editor The number you want to edit must be on the display Left (Menu) 9 removes the digit left of cursor ▼ or ▲ moves the cursor right or left Õ F ÕC Õ This function lets you edit the existing digits of a phone number. You can press to dial the edited number. U Menu 10, Alert Options With Ring & Vibra the phone rings and vibrates for incoming calls. With Ring the phone sounds a ringing tone. With Beep Once the phone sounds a short beep. With Vibrate the phone only vibrates.
Menu 11, Activate Keyguard Press left then 11 F (Menu) Keyguard remains on until you deactivate by pressing left (Menu) then ∗. When the function is activated and there is no call in progress, no key tones are heard and no key presses are be accepted, except for calls to 911 (or other official preprogrammed emergency number) and and . F U E When placing an emergency call, the emergency number is displayed only after you have keyed in all its digits.
11. Data and Fax Calls The phone can send or receive data when it is connected to a compatible data terminal (such as a fax machine or PC) through a data adapter. See the documentation for the data adapter and terminal. Only analog data can be sent and received. The phone recognizes the type of the connected terminal automatically. For instance, if a fax machine is connected to the phone, the phone makes a fax call.
To receive a fax call Ê Check that the data terminal is properly installed. U Ë Press to answer the call. OR, if you know this is an incoming fax, you can answer the call from the fax machine’s keypad. Ì After the transmission, end the call from the fax machine’s keypad. OR, press .
12. Accessories In addition to the battery and chargers described in this manual, an extensive accessory range is available. You can select the accessories that meet your specific communication needs. For availability, please check with your local dealer. Use only batteries, antennas, chargers, and accessories approved by the phone manufacturer. The use of any other types will invalidate any approval or warranty applying to the telephone, and may be dangerous.
Note: Battery operation times vary according to signal conditions, network parameters set by the operator, and how you use the batteries. Using the phone near the network’s base station consumes less power. Keeping the antenna fully extended whenever possible maintains the connection to the network with less power. Approximate charging times Battery ACH-3U ACH-4U Slim BBH-1S 4.5 hours 1 hour BBT-1XV Vibrating 4.5 hours 1 hour Ultra Extended 9 hours 2 hours BBH-2H Ultra Extended 14 hours 2 hours, 30 min.
The charger can also be used together with the optional Compact Desktop Charging Stand (CHH-2) and Light Desk Stand (CHH-2L). Fast Cigarette Lighter Charger (LCH-2) You can charge the phone battery from your vehicle battery by using the Fast Cigarette Lighter Charger (LCH-2). You can also use the charger with stands CHH-2 and CHH-2L (described below). Calls are possible during charging.
The charger starts to charge the spare battery as soon as it has finished charging the phone battery. Connect either the Fast Travel Charger (ACH-4U) or the Fast Cigarette Lighter Charger (LCH-2) to the stand, and then plug the Fast Travel Charger or Fast Cigarette Lighter Charger into a wall outlet or vehicle respectively. Place the phone and/or the spare battery in the stand. To discharge the spare battery, press the blue button on the stand.
13. Care and Maintenance Your phone is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you to fulfill the warranty obligations and to enjoy this product for many years. Keep the phone and all its parts and accessories out of small childrens’ reach. Keep the phone dry. Precipitation, humidity and liquids contain minerals that will corrode electronic circuits. Do not use or store the phone in dusty, dirty areas. Its moving parts can be damaged.
14. Technical Data Cellular System TDMA and AMPS Weight 7.9 oz (224g) with 550mAh NiMH battery Capacity 169 cc Frequency Range 824.010 - 848.970 MHz (TX) 869.010 - 893.970 MHz (RX) Transmitter Output Power 0.
NOKIA One-Year Limited Warranty Nokia Mobile Phones, Inc. (“NMPI”) warrants that this cellular phone (“Product") is free from defects in material and workmanship, according to the following terms and conditions: 1. The limited warranty for the Product extends for ONE (1) year beginning on the date of purchase of the Product. 2. The limited warranty extends only to the original consumer purchaser (“Consumer”) of the Product and is not assignable or transferable to any subsequent purchaser/end user. 3.
c) The Product serial number plate or the accessory date code has been removed, defaced, or altered. d) The defect or damage was caused by the defective function of the cellular system, or by inadequate signal reception by the external antenna. 8. If a problem develops during the limited warranty period, the Consumer should take the following step-by-step procedure: a) The Consumer shall return the Product to the place of purchase for repair or replacement processing.
10. ANY IMPLIED WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OF USE, SHALL BE LIMITED TO THE DURATION OF THE FOREGOING WRITTEN WARRANTY, OTHERWISE, THE FOREGOING WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED.
14. Technical Data Cellular System TDMA and AMPS Weight 7.9 oz (224g) with 550mAh NiMH battery Capacity 169 cc Frequency Range 824.010 - 848.970 MHz (TX) 869.010 - 893.970 MHz (RX) Transmitter Output Power 0.
