Produ uct Ope O ratio on Manu M ual MS SH-HSD D080W-1 18X/23X X/26X Ne etwork IP I High Speed Dome D Microseven Sy ystems, Inc c.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome -2- First Edition (April 2008) Copyright Notice Copyright © 2002-2008 Microseven Systems, Inc. All Rights Reserved. Microseven Systems, Inc. provides this operation manual “as is” without warranty of any kind, either express or implied, including, but not limited to the implied warranties of merchantability and fitness for a particular purchase. Microseven Systems, Inc.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome -3- Contents 1. Preface ………………………………………………………………………………… 4 2. Key Features ………………………………………………………………………………… 4 3. Notes …………………………………………………………………………………………… 5 ……………………………………………………………… 6 5. Connections ……………………………………………………………………… 7 6. Installation of Camera ……………………………………………………………………… 9 4. Instructions of Main Parts ………………………………… 14 …………………………………………. 14 …………………………..
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome -4- 1. Preface MSH-HSD080W-18X/23X/26X network IP high speed dome cameras adopt SONY / Hitachi zoom module, with bright and exquisite images. As video & audio multi-media equipment that based on network transmission, which adopts built-in and multi-media communication technology, the camera is a multi-media network terminal that can directly connect to the network.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome -5- alarm signal will be transmitted to appointed client-end through network, image capturing & recording or other relevant actions can be set. Digital matrix function: can realize common analog matrix functions like switch & setup auto switch time etc. Special keyboard can be directly connected to the network, controlled speed domes and switched images. With IEEE 802.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome 4. Instructions for Main Parts ① Power connector ⑥ Secure chain ② RJ45 internet connector ⑦ Upper base ③ Audio connector ⑧ Body ④ Alarm connector ⑨ Transparent cover ⑤ Pipe © 2002-2008 Microseven Systems, Inc. All Rights Reserved.
5. Connectioons 5.1 Connec ction interfaces Audio C Connector A Alarm Conne ector Power C Connector 8 PIN c 5.
Micro oseven® MSH-H HSD080W-18X//23X/26X Netwo ork IP High Spe eed Dome -8- 5.3 Power c connection Brrown Ye ellow Blue connection 5.4 Power c 8 PIN interrface c 5.5 RJ-45 connections - 8PIN standard d GM line - Ultra-five - Recommende R ed maximum length: 80m m © 2002-2008 Microseven System ms, Inc. All Righ hts Reserved.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome -9- 5.6 Connection interfaces Alarm Connector Input Green Input Red Output A Always on port Yellow Output Blue Indicator Power 6. Installation of Camera " The following installation should be undertaken by qualified service personnel or system installers. " Ensure that you have cut off the power during the installation process. " The following installation method is outdoor hoisting and wall hoisting.
Micro oseven® MSH-H HSD080W-18X//23X/26X Netwo ork IP High Spe eed Dome - 10 - 6.1 Prepara ation A. Pu urchasing ce eiling mount bracket. b B. Ch hoose the ins stallation pla ace (Note: Please choose e an installation place wh hich is strong g en nough to bea ar the camera a weights.) C. Prrepare installation access sories. 6.2 Disasse embly the ca amera A. Re emoving upp per base from m camera by y loosening 3 screws, sep parate it from m the camera a. Lock B.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome - 11 - B. Fix the bracket on the installation surface by screws. C. Thread cables through the bracket. D. Use 3 screws to fix upper base to accessory pipe, filling the gap between bracket and accessory pipe with water-proof materials. 6.4 Install camera A. Aiming “START” arrow to the bent portion of the spring. B. Ensure that the secure chain hooks the bracket. C. Fix the camera to the upper base.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome - 12 - i. Move up the camera; let the guide pins fit into upper base guide holes. ii. Turn the camera counter-clockwise to the end. (Please make sure the camera had been turned to the lock position before release your hand.) iii. Fasten 3 screws. 6.5 Remove protection pads " Please make sure that you have set up the camera already before proceed following operations. A. Remove 4 screws on the lower ring.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome B. Remove protection pad and lens shield. C. Install transparent hemisphere shield to the camera, fasten the screws to ensure water-proof. (Please reference to 6.5 B.) © 2002-2008 Microseven Systems, Inc. All Rights Reserved.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome - 14 - 7. Basic System Diagram and Operating Circumstance Operate environment After the equipment installed and connected to the network, it should be operated on Server Software Platform of Microseven Digital Video Server. 8. Network High Speed Dome Camera Operation 8.1 Pan/Tilt Operator can use the joystick of the controller (MSH-CU7502) to operate pan/tilt for up, down, left, right movement.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome - 15 - 8.3 ZAP operation ZAP function is to automatically adjust pan/tilt speed when camera is zooming in/out, using complex algorithm. Provides right surveillance image all the time. 8.4 Lens operation Lens operation is zoom in/out, focus and iris control. A. Zoom User can control zoom in/out in the client-end software function “Zoom”. Through this control, user can get closer and wider view of the image.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome - 16 - 8.6 PTZ automatic scanning PTZ automatic scanning will proceed with 360 degree continuously rotation with a stable speed. The speed is determined depends on current lens zoom status. i. Make sure that there is no pan/tilt action before start the auto scanning; ii. Click Auto Rotate button to start the auto scanning; User can stop the auto scanning by any operation orders during the auto scanning process; 8.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome - 17 - 9. Transparent Shield Cleaning In order to generate clear image, the transparent shield of the dome camera should be cleaned periodically. " Cleaning with caution, please hold the outer edge of the shield; avoid the directly contact with the shield because the acid sweat of your finger may erode the coating cover. Scratches may lower the image quality.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome Preset 188 Home Position Can select any preset from 1-188 Privacy Masking Open/Close (2 privacy areas) Motion Detection Function Open/Close (8 areas) White Balance Auto/Manual BLC Close/Open Focus Auto/Manual Shot Auto/Manual Iris Control Auto/Manual AGC Control Auto/Manual Day/Night Switch Auto/Manual Wide Dynamic Range Auto/Manual Image Mirror Function Open/Close Image Freeze Function Open/Close Network Interface
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome - 19 - 11.
Microseven® MSH-HSD080W-18X/23X/26X Network IP High Speed Dome - 20 - Appendix --- Lightening and Surge Protection " This product uses TVS lightening-proof technology, which can protect the camera from the damage by sudden lightening strike with power consumption no higher than 1.5KW, and surge or other type of electronic pulses.