User manual

(35) [Beep]=4-2-2 shutdown test in progress or failure.
(36) [Beep]=4-2-3 gate A20 failure. Warm start shut down . Configure EMS
memory option.
(37) [Beep]=1-4-2-4 unexpected interrupt in protected mode. Reinitialize the
motherboard chipset.
(38) [Beep]=4-3-1 RAM test in progress or failure above address 0FFFFh
(38) Shadow system BIOS ROM.(Beep)=1 -4-3-1.Configure wait state option.
(39) Reinitialize the cache.(Beep)=1 -4-3-1
(3A) [Beep]=4-3-3 Interval timer channel 2 test in progress or failure.
(3A) Auto -size cache.(Beep)=1 -4-3-3.Retest 64K base RA M.
(3B) [Beep]=4 -3-4 Time-Of-Day clock test in progress or failure.
(3C) [Beep]=4 -4-2 Serial port test in progress or failure.
(3D) Load alternate registers with CMOS values,(Beep)= 1 -4-4-2
(3D) [Beep]=4-4-2 Parallel port test in progress or failure.
(3E) Get switches/jumper status from 8742.
(3E) [Beep]=4-4-3 Math CoProcessor test in progress or failure.
(40) Set initial CPU speed.(Beep)=2 -1-1-1.
(42) Initialize interrupt vectors.(Beep)=2 -1-1-3.
(44) Initialize BIOS interrupts.(Beep)=2 -1-2-1. Verify video con figuration.
(45) POST device initialization.
(46) Check ROM copying notice.(Beep)=2 -1-2-3. Initialize video system.
(47) Initialize manager for PCI Options ROMs.(Beep)=2 -1- 2-4.
(48)Check Video configuration against CMOS.(Beep)=2 - 1-3-1. Test for
unexpected interrupts.
(49) Initialize PCI bus and devices.(Beep )=2-1-3-2.
(4A) Initialize all video adapters in system.(Beep)=2 -1-3-3. Start 2nd protected
mode test.
(4B) Quiet-Boot start(optional).
(4C) Shadow video BIOS ROM.(Beep)=2 -1 -4-1.Perform LDT instructions test.
(4E) Display copying notice.(Beep)=2 -1-4-3. Perform TR instruction test.
(50) Display CPU type and speed.(Beep)=2 -2-1-1.(50)Per- form LSL instruction
test.[Beep]=none Custom chip set or custom platform.
(51) Initialize EISA board.
(52) Test keyboard.(Beep)=2 -2-1-3.(52)Perform LAR instruction test.
(54) Set key click if enabled.(Beep)=2 -2-2-1.(54)Perform VERR instruction test.
(56) Enable keyboard.(Beep)=2-2-2-3.Unexpected exception.
(58)Test for unexpected interrupts.(Beep)=2 -3-3-.(58) Perform A20 gate test.
(59) Initialize POST display service.
(5A) Keyboard ready test. Display prompt "press F2 to enter SETUP".(Beep)=2
-2-3-3
(5B) Display CPU cache.
(5C) Test RAM between 512 and 640K.(Beep)=2 -2-4-1. Determine if AT or KT
keyboard type.
(5E) Enter third protected mode test.
(60) Test expanded memory.(Beep)=2 -3-1-1.(60)Base memory test.
(62) Test extended memory address lines.(Beep)=2 -3-1-3. Base memory address
25