Installation guide

4
3
1 2
Introduction
Micronet SP3508A is an EoVDSL (Ethernet over VDSL)
clustering switch that aggregates 8 VDSL lines into 2 Gigabit
Ethernet uplinks. It delivers cost-effective and high-performance
broadband / multimedia services to multiunit building
environments, such as enterprise, campus, hospital, hotel, and
telecom. With QAM-based 4-band VDSL technology, the VDSL
solution dramatically extends Ethernet and supports
5M/15M/25Mbps symmetrical bandwidth over existing
telephone-grade wiring up to 1.7 /1.1/0.6KM.
Package Contents
Prior to the installation of the device, please verify the following
items are in the package:
SP3508A VDSL Managed Switch
Quick Installation Guide
Manual CD
Mounting Accessories
AC Power Cord
•
•
•
•
•
Key Features
Compliant with ETSI, ITU, ANSI standards
Compliant with IEEE802.3 10BASE-T, IEEE802.3u 100BASE-
TX and IEEE 802.3ab 1000BASE-T standards
Support 8 x RJ-11 VDSL ports and 8 x RJ-11 POTS ports
Support 2 x RJ-45 ports of 10/100/1000M for Gigabit uplink
QAM-based 4-band VDSL
Data rate up to symmetrical bandwidth of 25Mbps
Wiring range up to 1.7 KM
Auto-speed function for VDSL link
Built-in POTS/ISDN splitter for POTS/ISDN telephone service
Support detection of wiring quality with SNR(Signal to Noise
Ratio) indications
Full function of Layer 2 managed switch: IEEE 802.1q/p Tag-
based VLAN, IEEE 802.1v Protocol-based VLAN,
IEEE802.3ad LACP, IEEE 802.1d Spanning tree, IGMPv2,
MAC/IP filtering, Port Mirror, and Broadcast Storm Control
SNMPv1 and MIBs support: Bridge MIB, Ethernet MIB, MIB II
Support management via Console Port, Telnet and Web-
Based
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Physical Description
Modem Connectors
Cabling Requirements
Connectors
VDSL (1~8)
POTS (1~8)
Gigabit Ethernet
Reset
Description
Connecting to the VDSL Modem via
a RJ-11 cable
Connecting to the telephone, Fax or
ISDN modem
Connecting to an Ethernet network
device
Restart the switch
Type
RJ-11
RJ-11
RJ-45
Connection Type
Ethernet Port
(RJ-45)
VDSL Port
(RJ-11)
Cable Requirements
100 Mbps: Cat 5 UTP
10 Mbps: Cat 3-4 UTP
18-26 Gauge phone wiring.
Do not recommend 28 or
above Gauge.
Maximum Length
100 meters max
for MUX or HUB
to endpoint.
5M/5M: 1.7km
15M/15M: 1.1km
25M/25M: 600m
LED definition
LED
PWR
(Power LED)
POST
(Power On Self
Testing)
LINK
(VDSL LED)
10/ACT
(Ethernet LED)
100/ACT
(Ethernet LED)
1000/ACT
(Ethernet LED)
Status
Steady/Green
Steady/Green
Off
Steady/Green
Steady/Green
Flash/Green
Steady/Green
Flash/Green
Steady/Green
Flash/Green
Operation
Device is powering on or reset
ok
Light on when device is
booting
Turn off when booting is
finished
Each VDSL port has a LED and
lights up to show good linkage
Light up steadily to show good
linkage at 10 Mbps
Flashing to show data
transmission
Light up steadily to show good
linkage at 100 Mbps
Flashing to show data
transmission
Light up steadily to show good
linkage at 1000 Mbps
Flashing to show data
transmission