Setup guide
Table Of Contents
- Table of Contents
- 1 General information (setting up microHAM and N1MM logger)
- 2 SO2R Setup at PA1M - microHAM MK2R+ and Station Masters and N1MM logger
- 2.1 Layout cabling
- 2.1.1 MK2R+ Station Master Connection diagram (by Joe, W4TV)
- 2.1.2 Shack PA1M
- 2.1.3 Stationmaster
- 2.1.4 Nr 6 - Port A - Antennaswitch (DB25F) microHAM DOUBLE TEN SWITCH
- 2.1.5 Nr 14 - Port B - bandpassfilter, sequencer (DB25F) ICE-419A BPF
- 2.1.6 Nr 5 - Port PA - Power Amplifier (DB15F)
- 2.1.7 Nr 13 - Port ROTOR - Antenna Rotator (DB15F)
- 2.1.8 StationMaster cabling
- 2.1.9 Setup Station Master
- 2.1.10 Setup uRouter
- 2.2 DOUBLE TEN Port lockout with Station Masters
- 2.3 Radio settings
- 2.4 microHAM Router setup
- 2.5 Station master setup
- 2.6 N1MM logger setup
- 2.7 MMTTY setup
- 2.8 PC setup
- 2.9 Errors and other problems
- 2.10 Detailed Cabling Diagrams
- 2.1 Layout cabling
- 3 N1MM - RTTY operation / settings
Pin 19 − CONTROL GND
Pin 20 − B1
Pin 21 − B2
Pin 22 − B3
Pin 23 − B4
Pin 24 − B5 only( SM2
Pin 25 − B6
Gray/Brown
Red
Yellow
Pink
Blue
White
Green
Chassis Ground ICE BPF
ICE 160 mtr
ICE 80 mtr
ICE 40 mtr
ICE 20 mtr
ICE 15 mtr
ICE 10 mtr
Temporarily: Port B5 from SM 1 is broken, now using port B7: Connect Pin 4 to Pin 6 Pin 10 − B7 SM1
2.1.6 Nr 5 − Port PA − Power Amplifier (DB15F)
Tentec Titan: Has both a KEY IN (=PTT) and a KEY OUT (inhibit for QSK). Using the Key OUT has
to be enabled in the Station Master PA & Sequencer Tab (INH).
Heathkit SB−220: Only has a PTT connector so only pin7 used from the Station Master. No inhibit
signal used.
SM − Port PA Tentec Titan SB−220
Pin 6 − KEYIN
Pin 7 − KEYOUT
KEY OUT (lower one)
KEY IN (upper two)
−
PTT
2.1.7 Nr 13 − Port ROTOR − Antenna Rotator (DB15F)
Maybe one day.
2.1.8 StationMaster cabling
Make sure you used the correct connections: pin 7 for "key out" (to the Key in or PTT jack of the
Acom), pin 6 for "key in" (from the "key out" or "amp ready" jack on the Acom) and pins 13/14/15 for
ground (shield of the two control lines).
Relays used in Station Master are: TOWRD N4100HS3DC12V 3A/125VAC/30VDC
2.1.9 Setup Station Master
Hold FUNC/MENU button: Select: *** CAT ***
Don't forget to set the jumpers inside!!
2.1.10 Setup uRouter
Ports tab: iLink couple: micro KEYER 2R+ (RADIO 1) for Radio 1 and micro KEYER 2R+
(RADIO 2) for Radio 2.
Antenna Switching & PTT Sequencer: Load from File and Store
2.2 DOUBLE TEN Port lockout with Station Masters
2.2.1 Solution 1 by Josef − OM7ZZ
For this soution to work the outputs with both contact poles avaliable (B7, B8, B9, B10) should not be
used.
− Output from left SM port A1 connect also to B7−NO on righ SM.
− Output from left SM port A2 connect also to B8−NO on righ SM.
13−2−20092 SO2R Setup at PA1M − microHAM MK2R+ and Station Masters and N1MM logger 15