Microframe Corporation Series 3500: The MultiPage System Operating Manual B3010-7013 *B3010-7013*
SERIES 3500 The MultiPage System INSTALLATION & SPECIFICATION GUIDE ITEM NO: B3010-7013 REVISION DATE: 06/09 Microframe Corporation 604 S. 12th Street Broken Arrow, OK 74012 Tel: (918) 258-4839 Toll Free: 1-800-635-3811 Website: www.microframecorp.com E-mail: support@microframecorp.
Limited Warranty Agreement Your Microframe System is warranted against failure due to defects in workmanship or material for a period of one (1) year from the date of purchase. Microframe Corporation will repair or replace any defective unit. Obvious abuse or mishandling of the unit is NOT covered by this warranty. Merchandise Return If your Unit does not work satisfactorily, please give us a call. We may be able to solve the problem by phone.
TABLE OF CONTENTS 1 MULTIPAGE SYSTEM OVERVIEW ............................... 6 1.1 MultiPage Transmitter .....................................................6 1.2 Wireless UHF Displays ....................................................6 1.3 Paging Vibrating Pagers ..................................................6 MULTIPAGE SPECIFICATIONS ........................................ 7 2 MULTIPAGE OPERATION .............................................. 9 2.1 Installation...................................
Microframe Corporation 1 MULTIPAGE SYSTEM OVERVIEW With the MultiPage Transmitter, you can send numbers to UHF Displays and page Vibrating Pagers. A MultiPage system is defined as one MultiPage Transmitter and any combination of these receiver types. 1.1 MULTIPAGE TRANSMITTER The MultiPage Transmitter is a unique Transmitter that facilitates the use of UHF Displays and Pagers.
Microframe Corporation Series 3500 - MultiPage System MULTIPAGE SPECIFICATIONS On-Premise Paging Features The MultiPage Transmitter can be used to transmit to the following receivers: The Wireless UHF Display and Vibrating Pagers. The MultiPage LCD screen displays two lists: The first list consists of the numbers being shown on the UHF Wireless Display. The second list shows the Pagers waiting to be re-paged. Operation Simply plug the power adapter into the back of the MultiPage and it is ready to use.
Microframe Corporation 8 Series 3500 - MultiPage System
Microframe Corporation Series 3500 - MultiPage System 2 MULTIPAGE OPERATION 2.1 INSTALLATION The MultiPage Transmitter is designed to set on a flat surface or table top or installed on a mounting wedge for an angle or wall mount. To use the Transmitter, simply plug the 12-volt DC power adapter into the back of the MultiPage and then plug the adapter into the wall. The MultiPage Transmitter is now ready for use. 2.
Microframe Corporation Option 3 Re-Page Time for Vibrating Pagers This is the time between re-pages for Vibrating Pagers. For example, if the re-page time is set to one minute, then the Vibrating Pagers will be repaged every minute. Using the “(“ and “)” keys you can choose between 0 and 25 minutes for the repage time. A re-page time of 0 disables re-paging. When the desired value is selected, press “ENTER” to return to the main options menu.
Microframe Corporation Series 3500 - MultiPage System UHF DISPLAY SPECIFICATIONS On-Premise Paging Features The UHF Displays are designed to work best with the Microframe MultiPage System. The Displays have two modes: 1) As a "Visual-Pager," the Display will store and rotate up to 20 numbers at a time. Numbers can be entered and deleted from the Display using the MultiPage Transmitter. 2) The Display can also be used as a "Pager Confirmation System.
Series 3500 - MultiPage System Microframe Corporation 3 WIRELESS UHF DISPLAY 3.1 INSTALLATION Step 1: Wire in the power adapter. To do this, simply place one wire from the adapter under one of the screwdown terminals and the other wire under the other screwdown terminal as shown on page 11. At this point, plug in the power adapter and check the Display for proper operation. Step 2: Hang the Display. The Display is hung on the wall like a picture frame on a nail or screw.
Microframe Corporation Series 3500 - MultiPage System 3 WIRELESS UHF DISPLAY 3.332 Auto Delete Setting The Display can be set to automatically delete a number from its memory after a preset time. NOTE: If you have a MultiPage Transmitter, use the Transmitter's auto delete rather than the Display's auto delete time. To set the auto delete time send a page to Pager 9999 with the message “02_XX” where XX is a number from 1 to 42 representing the number of minutes to wait before auto deleting. 3.
Series 3500 - MultiPage System Microframe Corporation POCKET PAGER SPECIFICATIONS On-Premise Paging Features The Scope Pocket Pager is designed to work with the MultiPage or DataPage family of on-premise transmitters. The pager can show unlimited numeric messages sent by the transmitter. Optionally, the pager can show up to three factory pre-programmed text messages corresponding to the beep type specified. Pocket Pager Support and Sales Pocket Pager Specifications Distance Range .........................
Microframe Corporation Series 3500 - MultiPage System 5 POCKET PAGER 5.1 TURNING ON THE PAGER Hold down the LARGE GRAY BUTTON until the Pager comes on. 5.2 SENDING A PAGE Please see the diagram in the MultiPage section of this manual for detailed instructions on sending pages. 5.3 ACTIVATING AN ALPHA MESSAGE To activate a pre-defined message to a Vibrating Pager, type in the Pager number followed by the "SEND" key. You will be prompted for a “BEEP TYPE (1-4).” Select 1-3 here and press the “SEND” key.
Series 3500 - MultiPage System Microframe Corporation NEXUS PAGER SPECIFICATIONS On-Premise Paging Features The Nexus Pager is designed to work with the MultiPage or DataPage family of on-premise transmitters. The rechargeable pager can show unlimited numeric messages sent by the transmitter. Optionally, the pager can show up to three factory pre-programmed text messages corresponding to the beep type specified. Nexus Pager Support and Sales Nexus Pager Specifications Distance Range ......................
Microframe Corporation Series 3500 - MultiPage System 6 NEXUS PAGER 6.1 TURNING ON THE PAGER Hold down the RED BUTTON on the side until the pager comes on. 6.2 SENDING A PAGE Please see the diagram in the MultiPage section of this manual for detailed instructions on sending pages. 6.3 ACTIVATING AN ALPHA MESSAGE To activate a pre-defined message to a Vibrating Pager, type in the Pager number followed by the "SEND" key. You will be prompted for a “BEEP TYPE (1-4).
Series 3500 - MultiPage System Microframe Corporation SLIMLINE PAGER SPECIFICATIONS On-Premise Paging Features The SlimLine Pager is designed to work with the MultiPage or DataPage family of on-premise transmitters. The rechargeable pager has vibrate only and LED alert capability. SlimLine Pager Support and Sales SlimLine Pager Specifications Distance Range .........................................1/4 to 1/2 mile Power ........................................................Rechargeable Size.............
Microframe Corporation Series 3500 - MultiPage System 7 SLIMLINE PAGER 7.1 SENDING A PAGE Please see the diagram in the MultiPage section of this manual for detailed instructions on sending pages. 7.2 SENDING A GROUP CALL PAGE All pagers respond to call number “900” (unless another group call number has been chosen by the customer and programmed at the factory). To page all pagers at once, simply enter “900” and "SEND." Then press "SEND" again at the beep type prompt. 7.
Series 3500 - MultiPage System Microframe Corporation AFFINITY PAGER SPECIFICATIONS On-Premise Paging Features The Affinity Pager is designed to work with the MultiPage or DataPage family of on-premise transmitters. The rechargeable vibrating pager has illuminating lights, vibrate and tone alert options for personalization. Affinity Pager Support and Sales Affinity Pager Specifications Distance Range .........................................1/4 to 1/2 mile Power .............................................
Microframe Corporation Series 3500 - MultiPage System 8 AFFINITY PAGER 8.1 SENDING A PAGE Please see the diagram in the MultiPage section of this manual for detailed instructions on sending pages. 8.2 SENDING A GROUP CALL PAGE All pagers respond to call number “900” (unless another group call number has been chosen by the customer and programmed at the factory). To page all pagers at once, simply enter “900” and "SEND." Then press "SEND" again at the beep type prompt. 8.
Series 3500 - MultiPage System Microframe Corporation Microframe Corporation 604 S. 12th Street Broken Arrow, OK 74012 Tel: (918) 258-4839 Toll Free: 1-800-635-3811 Website: www.microframecorp.com E-mail: support@microframecorp.
