SERIES 3500 MultiPage System INSTALLATION and SPECIFICATION GUIDE Microframe Corporation 604 South 12th Street Broken Arrow, OK 74012 Local: 918-258-4839 Toll Free: 800-635-3811 Website: www.microframecorp.com E-mail: support@microframecorp.com Manual No. B3011-7013 Revision Date: 02/2013 Control: 1.
Limited Warranty Agreement Your Microframe System is warranted against failure due to defects in workmanship or material for a period of one (1) year from the date of purchase. Microframe Corporation will repair or replace any defective unit. Obvious abuse or mishandling of the unit is NOT covered by this warranty. Merchandise Return If your Unit does not work satisfactorily, please give us a call. We may be able to clear up the problem by phone.
Series 3500 MultiPage System Installation and Specification Guide Table of Contents MultiPage System Overview and Features MultiPage System Instructional Diagram MultiPage Transmitter Features and Operation Visual-Pager® Display Features and Operation Visual-Pager® Display Detailed Operation Pocket Pager 2 Operation Nexus Pager Operation Slimline Pager Operation Affinity Pager Operation Microframe Corporation th 604 South 12 Street Broken Arrow, OK 74012 800-635-3811 www.microframecorp.
MultiPage System Overview The MultiPage System is a “plug and play” paging solution that consists of a transmitter and a display or pager. The system may have more than one transmitter, and more than one display or pager, or any combination of these items. With this system you may page vibrating pagers and/or send assigned numbers to a Wireless Microframe Visual-Pager®.
MultiPage System Instructional Diagram Sending Pages and Numbers A s you type in n um b ers you will see NOTE: P ressing "C A N C E L" from an y p oin t in the "s en d in g p ages an d n um b ers" d iag ram will take you back to th e "R ead y" screen . R eady E nter:452 P ress "E N TE R " to send a n u m ber to a D isplay.
Installation The MultiPage Transmitter is designed to set on a flat surface or table top, or to be installed on a mounting wedge for an angle or wall mount. To use the transmitter, simply plug the 12-volt DC power adapter into the back of the transmitter and then plug the adapter into the wall. The transmitter is now ready to use. MultiPage Transmitter Operation The MultiPage Transmitter has two primary operations.
MultiPage Transmitter Detailed Operation Programmable Configurations, Options continued… OPTION 3 – Re-Page Time for Vibrating Pagers This is the time between re-pages for vibrating pagers. For example, if the re-page time is set to one minute, then the pager will be re-paged every minute. Using the “*” and “#” keys, you may choose between 0 and 25 minutes for the re-page time. A re-page time of 0 disables the re-paging feature.
Features The Visual-Pager® displays are designed to work best with the Microframe MultiPage System. The displays have two modes: 1) As a "Visual-Pager®," the display will store and rotate up to 20 numbers at a time. Numbers can be entered and deleted from the display using the MultiPage Transmitter. 2) The display can also be used as a "Pager Confirmation System." In this mode, the display shows the number of every vibrating pager that has been paged.
Visual-Pager® Display Detailed Operation Installation 1. Wire in the power adapter. To do this, simply place one wire from the adapter under one of the screwdown terminals and the other wire under the other screwdown terminal (refer to the wiring diagram decal on the back of the display.) Then, plug in the power adapter and check the display for proper operation. 2. Microframe displays can be hung on the wall similar to a picture frame. There is a keyhole in the back of the display for this purpose.
Visual-Pager® Display Detailed Operation Configuration, Mode Settings continued… o Roll-Over Time Setting The Roll-Over Time is the time each number in the display memory is shown before changing to the next number. This time can be set from 1 to 9 seconds. To set this time, send a page to Pager 9999 with the message “01_0X” where X is a number 1-9 representing the number of seconds. o Auto Delete Setting The display can be set to automatically delete a number from its memory after a preset time.
Features The Pocket Pager 2 is designed to work with the MultiPage family of on-premise transmitters. The battery-powered pager can show any numeric message sent by the transmitter. Optionally, the pager can show up to three factory preprogrammed text messages corresponding to the beep type specified. Pocket Pager 2 Turning on the Pager Hold down the LARGE BLACK BUTTON until the pager comes on.
Features The Nexus Pager is designed to work with the MultiPage family of on-premise transmitters. The rechargeable pager can show unlimited numeric messages sent by the transmitter. Optionally, the pager can show up to three factory pre-programmed text messages corresponding to the beep type specified. Nexus Pager Turning on the Pager Hold down the RED BUTTON on the side until the pager comes on.
Features The Slimline Pager is designed to work with the MultiPage family of on-premise transmitters. The rechargeable has vibrate-only and LED alert capability. Slimline Pager Sending a Page Please see the diagram in the MultiPage section of this manual for detailed instructions on sending pages. Sending a Group Call Page All pagers respond to call number “900” (unless another group call number has been chosen by the customer and programmed at the factory).
Features The Affinity Pager is designed to work with the MultiPage family of on-premise transmitters. The rechargeable vibrating pager has illuminating lights, vibrate and tone alert options for personalization. Affinity Pager Sending a Page Please see the diagram in the MultiPage section of this manual for detailed instructions on sending pages.
