台揚企業集團 ISO 9001 Certified MTI Group. MTI RFID Reader Operation Manual LTR. AS ISSUED E.C.O. NO. DATE Steven Kao CHANGE INFORMATION REVISED AUTHOR HISTORY DWG NO. 43-RFID0900-E1-MANUAL APPROVED BY PAGE NO.
LTR. E.C.O. NO. DATE CHANGE INFORMATION REVISED AUTHOR HISTORY DWG NO. 43-RFID0900-E1-MANUAL TITLE: MTI RFID Reader Operation Manual 台揚集團智慧財產 任何未經授權逕予複製、重製、公開或使用本文之行為，將被視為侵害 台揚集團之智慧財產權，將可因此負擔法律責任。 MTI Group Proprietary Information Any unauthorized use, duplication, reproduction, or disclosure of this document may be considered as infringement of MTI Group’s intellectual property rights, the infringer may be accused and liable applicable legal penalties.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 3 DATE: 18-04-2006 Contents Chapter 1 – Introduction......................................................................................... 4 1.1 Purpose...................................................................................................... 4 1.2 Unpacking the Reader ............................................................................... 4 1.
台揚科技股份有限公司 ISO 9001 Certified MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL MICROELECTRONICS TECHNOLOGY INC. PAGE: 4 DATE: 18-04-2006 Chapter 1 – Introduction 1.1 Purpose This document provides users and technicians with instructions for installing and operating the MTI RFID RU-813 Reader Application. The MTI RFID Reader Application and associated documentation are provided as an aid for configuring your MTI RFID reader and is not intended as an engineering design system. 1.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 5 DATE: 18-04-2006 1.4 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 6 DATE: 18-04-2006 uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
台揚科技股份有限公司 ISO 9001 Certified MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL MICROELECTRONICS TECHNOLOGY INC. PAGE: 7 DATE: 18-04-2006 Chapter 2 – Installation 2.1 Antenna Installation The RU-813 supports from one Tx/Rx to four Tx/Rx external antennas in a variety of configurations. One- and two-antenna configurations are typical for most conveyor and container tracking. Four-antenna configurations are used for portals and loading dock doorways.
台揚科技股份有限公司 ISO 9001 Certified MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL MICROELECTRONICS TECHNOLOGY INC. PAGE: 8 DATE: 18-04-2006 The RU-813 is factory calibrated for operation with the following type of antenna and cable: Item Operating Frequency Impedance VSWR Polarization Gain Front to back ratio Axial ratio Connector Dimension Specification 902-928MHz 50Ohm <1.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 9 DATE: 18-04-2006 2.2 Reader Mechanical Installation TheRU-813 is designed for easy installation. The following instructions provide the information to install your UHF reader. As shown in figure 3, the reader is designed for horizontal installation. Mounting keyholes are provided on each side of the base plate for easy, non- permanent, installation and removal in figure 4.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 10 DATE: 18-04-2006 2.2.1 Hollow Concrete Block Wall Mounting To temporarily mount theRU-813 to a hollow concrete block wall, MTI recommends metal sleeve type concrete anchors that accept a #10 screw and flat washer. To install the reader on a hollow concrete block wall, perform the following. 1. Refer to Figure 4, and mark the location of the mounting screws.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. 1. 2. 3. 4. 5. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 11 DATE: 18-04-2006 Refer to Figure 4, and mark the location of the mounting screws. Drill the appropriate size hole for screws. Install the washers and insert the screws. Tighten the screws to within .375” of the surface. Install the reader and finish tightening the screws. 2.2.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 12 DATE: 18-04-2006 Chapter 3 – Configuration 3.1 Ethernet Overview When the reader is installed on a TCP/IP network connected to the internet, the reader must be assigned a unique IP address. The default IP address is set as 192.168.1.200, and the default subnet mask is set as 255.255.255.0, when the reader is shipped from factory. All these can be set by using web browser.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 13 DATE: 18-04-2006 3.3 Gateway Address Setup To set up IP address of RU-813 for Ethernet communication, perform the following steps: 1. 2. 3. 4. 5. 6. 7. Verify all cables and power supplies are secure and power up the readers. Set the subnet mask of host computer to the same subnet domain of reader. Open Web browser on your host computer.
台揚科技股份有限公司 ISO 9001 Certified MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL MICROELECTRONICS TECHNOLOGY INC. PAGE: 14 DATE: 18-04-2006 3.5 Setup Password Setup To set up password of RU-813 for Ethernet communication, perform the following steps: 1. 2. 3. 4. Verify all cables and power supplies are secure and power up the readers. Set the subnet mask of host computer to the same subnet domain of reader. Open Web browser on your host computer. Type IP address at web address on the browser. 5.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 15 DATE: 18-04-2006 Chapter 4 – Operation 4.1 Overview The RFID Reader Application is a Microsoft Windows application that provides a Graphical User Interface (GUI) for MTI RFID Reader Products.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 16 DATE: 18-04-2006 4.2 Startup MTI RFID Reader Application can communicate with all MTI readers through the Ethernet (TCP/IP) port. Verify your reader is connected to the correct port and power up. After connect power cord, the PWR LED light on the shell of reader will turn on. As figure 7. Figure 7 To start up MTI RFID Reader Application, perform the following: 1.
台揚科技股份有限公司 ISO 9001 Certified MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL MICROELECTRONICS TECHNOLOGY INC. PAGE: 17 DATE: 18-04-2006 4.3. Operating 4.3.1 Function Tabs RFID Reader Application operations are divided into two functional interfaces selected by tabs at the top of the display. Figure 9 functional tabs Read Function: Read tag data. Write Function: Write data to tag 4.3.2 Status Bar At the application below, the status bar provide the information of the operation.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 18 DATE: 18-04-2006 4.3.3 Connect Before read/write tag, you need to establish connection between PC and reader. Use [Connect] button to connect to reader. If application does not connect, verify the PC and reader’s Ethernet network setting. Please refer to Chapter 3 for further information network IP address Subnet mask IP address port PC 192.168.1.39 255.255.255.0 Reader 192.
台揚科技股份有限公司 ISO 9001 Certified MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL MICROELECTRONICS TECHNOLOGY INC. PAGE: 19 DATE: 18-04-2006 During the RF On period, if reader receive the response signal from tag, the RX LED light on the shell of reader will flash one time. Figure 12 RX LED light The Tag Read Time displayed in the lower window is the total tag read count since the last reset. The Antenna No is the tag be read by which Tx/Rx antenna.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 20 DATE: 18-04-2006 4.3.5 Write Data to Tag Step 1: Select which antenna to write data to tag. Step 2: Click the Scan button to search the tag in the range of antenna.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 21 DATE: 18-04-2006 Step 3: Fill up the four columns of the new tag ID. Step 4: Click the Lock button, then the button will change to Unlock.
台揚科技股份有限公司 ISO 9001 Certified MICROELECTRONICS TECHNOLOGY INC. MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL PAGE: 22 DATE: 18-04-2006 Step 5: Click the Write Tag button. Step 6: If write command success done, click Unlock to re-scan. And the new tag ID will display.
台揚科技股份有限公司 ISO 9001 Certified MTI RFID Reader Operation Manual 43-RFID0900-E1-MANUAL MICROELECTRONICS TECHNOLOGY INC. PAGE: 23 DATE: 18-04-2006 Chapter 5 – Specification This chapter describes the specification for MTI RFID RU-813 Reader Operating Frequency 910-920 MHz RF output power 29dBm RFID protocol EPC C1G2 V1.
