Datasheet
Table Of Contents
- 1.0 Introduction
- 2.0 USB3320 Pin Locations and Definitions
- 3.0 Limiting Values
- 4.0 Electrical Characteristics
- 4.1 Operating Current
- 4.2 Clock Specifications
- 4.3 ULPI Interface Timing
- 4.4 Digital IO Pins
- 4.5 DC Characteristics: Analog I/O Pins
- 4.6 Dynamic Characteristics: Analog I/O Pins
- 4.7 OTG Electrical Characteristics
- 4.8 USB Audio Switch Characteristics
- 4.9 Regulator Output Voltages and Capacitor Requirement
- 4.10 Piezoelectric Resonator for Internal Oscillator
- 5.0 Architecture Overview
- FIGURE 5-1: USB3320 Internal Block Diagram
- 5.1 ULPI Digital Operation and Interface
- 5.2 USB 2.0 Hi-Speed Transceiver
- 5.3 Bias Generator
- 5.4 Integrated Low Jitter PLL
- 5.5 Internal Regulators and POR
- 5.6 USB On-The-Go (OTG)
- 5.7 USB UART Support
- 5.8 USB Charger Detection Support
- 5.9 USB Audio Support
- 5.10 Reference Frequency Selection
- 6.0 ULPI Operation
- 6.1 Overview
- 6.2 ULPI Register Access
- 6.3 Low Power Mode
- 6.4 Full Speed/Low Speed Serial Modes
- 6.5 Carkit Mode
- 6.6 RID Converter Operation
- 6.7 Headset Audio Mode
- 7.0 ULPI Register Map
- 8.0 Application Notes
- 8.1 Application Diagram
- TABLE 8-1: Component Values in Application Diagrams
- TABLE 8-2: Capacitance Values at VBUS of USB Connector
- FIGURE 8-1: USB3320 Application Diagram (Device, ULPI Output Clock mode, 24MHz)
- FIGURE 8-2: USB3320 Application Diagram (Device, ULPI Input Clock mode, 60MHz)
- FIGURE 8-3: USB3320 Application Diagram (Host or OTG, ULPI Output Clock Mode, 24MHz)
- 8.2 Reference Designs
- 8.3 ESD Performance
- 8.1 Application Diagram
- 9.0 Package Information
- Appendix A: Data Sheet Revision History
- The Microchip Web Site
- Customer Change Notification Service
- Customer Support
- Product Identification System
- Worldwide Sales and Service
2014-2016 Microchip Technology Inc. DS00001792E-page 67
USB3320
APPENDIX A: DATA SHEET REVISION HISTORY
TABLE A-1: REVISION HISTORY
Revision Level & Date Section/Figure/Entry Correction
DS00001793E (05-31-16) Table 4-11, "USB3320 Quartz
Crystal Specifications"
Column headings modified.
DS00001792D (04-13-16) Table 4-3, "ULPI Interface
Timing"
Table heading corrected: “TYP” changed to “MAX”
DS00001792C (03-28-16) Table 4-3, "ULPI Interface
Timing"
Table heading corrected: “MAX” changed to “Units”
Section 9.1, "Package Mark-
ing Information," on page 63
Added package marking information.
Trademark and Sales Listing pages updated
DS00001792B (04-30-15) Updated temperature range offering throughout the document to reflect a single -40
to +85C option and adjusted product ordering codes accordingly
DS00001792A (08-14-14) Replaces previous SMSC version Rev. 1.0 (07-14-09)
Rev. 1.0 (07-14-09) Initial Release