Datasheet
Table Of Contents
- 1.0 Introduction
- 2.0 USB3320 Pin Locations and Definitions
- 3.0 Limiting Values
- 4.0 Electrical Characteristics
- 4.1 Operating Current
- 4.2 Clock Specifications
- 4.3 ULPI Interface Timing
- 4.4 Digital IO Pins
- 4.5 DC Characteristics: Analog I/O Pins
- 4.6 Dynamic Characteristics: Analog I/O Pins
- 4.7 OTG Electrical Characteristics
- 4.8 USB Audio Switch Characteristics
- 4.9 Regulator Output Voltages and Capacitor Requirement
- 4.10 Piezoelectric Resonator for Internal Oscillator
- 5.0 Architecture Overview
- FIGURE 5-1: USB3320 Internal Block Diagram
- 5.1 ULPI Digital Operation and Interface
- 5.2 USB 2.0 Hi-Speed Transceiver
- 5.3 Bias Generator
- 5.4 Integrated Low Jitter PLL
- 5.5 Internal Regulators and POR
- 5.6 USB On-The-Go (OTG)
- 5.7 USB UART Support
- 5.8 USB Charger Detection Support
- 5.9 USB Audio Support
- 5.10 Reference Frequency Selection
- 6.0 ULPI Operation
- 6.1 Overview
- 6.2 ULPI Register Access
- 6.3 Low Power Mode
- 6.4 Full Speed/Low Speed Serial Modes
- 6.5 Carkit Mode
- 6.6 RID Converter Operation
- 6.7 Headset Audio Mode
- 7.0 ULPI Register Map
- 8.0 Application Notes
- 8.1 Application Diagram
- TABLE 8-1: Component Values in Application Diagrams
- TABLE 8-2: Capacitance Values at VBUS of USB Connector
- FIGURE 8-1: USB3320 Application Diagram (Device, ULPI Output Clock mode, 24MHz)
- FIGURE 8-2: USB3320 Application Diagram (Device, ULPI Input Clock mode, 60MHz)
- FIGURE 8-3: USB3320 Application Diagram (Host or OTG, ULPI Output Clock Mode, 24MHz)
- 8.2 Reference Designs
- 8.3 ESD Performance
- 8.1 Application Diagram
- 9.0 Package Information
- Appendix A: Data Sheet Revision History
- The Microchip Web Site
- Customer Change Notification Service
- Customer Support
- Product Identification System
- Worldwide Sales and Service
USB3320
DS00001792E-page 10 2014-2016 Microchip Technology Inc.
4.0 ELECTRICAL CHARACTERISTICS
The following conditions are assumed unless otherwise specified:
V
VBAT
= 3.1 to 5.5V; V
DD18
= 1.6 to 2.0V; V
DDIO
= 1.6 to 2.0V; V
SS
= 0V; T
A
= -40C to +85C
The current for 3.3V circuits is sourced at the VBAT pin, except when using an external 3.3V supply as shown in
Figure 5-7.
4.1 Operating Current
Note 4-1 ClockSuspendM bit = 0.
Note 4-2 SessEnd, VbusVld, and IdFloat comparators disabled. STP Interface protection disabled.
TABLE 4-1: ELECTRICAL CHARACTERISTICS: OPERATING CURRENT
Parameter Symbol Condition MIN TYP MAX Units
Synchronous Mode Current
(Default Configuration)
I
33AVG(SYNC)
Start-up sequence defined in
Section 5.5.4 has
completed.
7.5 mA
I
18AVG(SYNC)
28.0 mA
I
IOAVG(SYNC)
4.1 mA
Synchronous Mode Current
(HS USB operation)
I
33AVG(HS)
Active USB Transfer 11.1 mA
I
18AVG(HS)
29.4 mA
I
IOAVG(HS)
5.9 mA
Synchronous Mode Current
(FS/LS USB operation)
I
33AVG(FS)
Active USB Transfer 6.3 mA
I
18AVG(FS)
22.5 mA
I
IOAVG(FS)
5.0 mA
Serial Mode Current
(FS/LS USB)
Note 4-1
I
33AVG(FS_S)
5.6 mA
I
18AVG(FS_S)
2.4 mA
I
IOAVG(FS_S)
86 uA
USB UART Current
Note 4-1
I
33AVG(UART)
5.6 mA
I
18AVG(UART)
2.4 mA
I
IOAVG(UART)
58 uA
Low Power Mode
Note 4-2
I
DD33(LPM)
V
VBAT
= 4.2V
V
DD18
= 1.8V
V
DDIO
= 1.8V
18.8 uA
I
DD18(LPM)
0.7 uA
I
DDIO(LPM)
30 uA
Standby Mode I
DD33(RSTB)
RESETB = 0
V
VBAT
= 4.2V
V
DD18
= 1.8V
V
DDIO
= 1.8V
18 uA
I
DD18(RSTB)
0.6 uA
I
DDIO(RSTB)
0.1 uA