Datasheet

 2010 Microchip Technology Inc. Preliminary DS39960B-page 243
PIC18F87K22 FAMILY
19.0 CAPTURE/COMPARE/PWM
(CCP) MODULES
PIC18F87K22 family devices have seven CCP
(Capture/Compare/PWM) modules, designated CCP4
through CCP10. All the modules implement standard
Capture, Compare and Pulse-Width Modulation (PWM)
modes.
Each CCP module contains a 16-bit register that can
operate as a 16-bit Capture register, a 16-bit Compare
register or a PWM Master/Slave Duty Cycle register.
For the sake of clarity, all CCP module operation in the
following sections is described with respect to CCP4,
but is equally applicable to CCP5 through CCP10.
Note: Throughout this section, generic references
are used for register and bit names that are
the same, except for an ‘x’ variable that
indicates the item’s association with the
specific CCP module. For example, the
control register is named CCPxCON and
refers to CCP4CON through CCP10CON.
Note: The CCP9 and CCP10 modules are
disabled on the devices with 32 Kbytes of
program memory (PIC18FX5K22).
REGISTER 19-1: CCPxCON: CCPx CONTROL REGISTER (CCP4-CCP10 MODULES)
(1)
U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0
— — DCxB1 DCxB0 CCPxM3
(2)
CCPxM2
(2)
CCPxM1
(2)
CCPxM0
(2)
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
-n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown
bit 7-6 Unimplemented: Read as ‘0’
bit 5-4 DCxB<1:0>: PWM Duty Cycle bit 1 and bit 0 for CCPx Module
Capture mode:
Unused.
Compare mode:
Unused.
PWM mode:
These bits are the two Least Significant bits (bit 1 and bit 0) of the 10-bit PWM duty cycle. The eight
Most Significant bits (DCx<9:2>) of the duty cycle are found in CCPRxL.
bit 3-0 CCPxM<3:0>: CCPx Module Mode Select bits
(2)
0000 = Capture/Compare/PWM disabled (resets CCPx module)
0001 = Reserved
0010 = Compare mode, toggle output on match (CCPxIF bit is set)
0011 = Reserved
0100 = Capture mode: every falling edge
0101 = Capture mode: every rising edge
0110 = Capture mode: every 4th rising edge
0111 = Capture mode: every 16th rising edge
1000 = Compare mode: initialize CCPx pin low; on compare match, force CCPx pin high (CCPxIF bit is set)
1001 = Compare mode: initialize CCPx pin high; on compare match, force CCPx pin low (CCPxIF bit is set)
1010 = Compare mode: generate software interrupt on compare match (CCPxIF bit is set, CCPx pin
reflects I/O state)
1011 = Compare mode: Special Event Trigger; reset timer on CCPx match
(CCPxIF bit is set)
11xx =PWM mode
Note 1: The CCP9 and CCP10 modules are not available on the devices with 32 Kbytes of program memory
(PIC18FX5K22).
2: CCPxM<3:0> = 1011 will only reset the timer and not start A/D conversion on CCPx match.