Datasheet

PIC18F2420/2520/4420/4520
DS39631E-page 328 © 2008 Microchip Technology Inc.
Supply Current (IDD)
(2)
PIC18LF2X2X/4X20 165 250 μA-40°C
V
DD = 2.0V
F
OSC = 1 MHz
(RC_IDLE mode,
INTOSC source)
175 250 μA+25°C
190 270 μA+85°C
PIC18LF2X2X/4X20 250 360 μA-40°C
V
DD = 3.0V270 360 μA+25°C
290 380 μA+85°C
All devices 500 700 μA-40°C
VDD = 5.0V
520 700 μA+25°C
550 700 μA+85°C
Extended devices only 0.6 1 mA +125°C
PIC18LF2X2X/4X20 340 500 μA-40°C
V
DD = 2.0V
F
OSC = 4 MHz
(RC_IDLE mode,
INTOSC source)
350 500 μA+25°C
360 500 μA+85°C
PIC18LF2X2X/4X20 520 800 μA-40°C
V
DD = 3.0V540 800 μA+25°C
580 850 μA+85°C
All devices 1.0 1.6 mA -40°C
VDD = 5.0V
1.1 1.4 mA +25°C
1.1 1.4 mA +85°C
Extended devices only 1.1 2.0 mA +125°C
26.2 DC Characteristics: Power-Down and Supply Current
PIC18F2420/2520/4420/4520 (Industrial)
PIC18LF2420/2520/4420/4520 (Industrial) (Continued)
PIC18LF2420/2520/4420/4520
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for industrial
PIC18F2420/2520/4420/4520
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ T
A ≤ +85°C for industrial
-40°C ≤ T
A ≤ +125°C for extended
Param
No.
Device Typ Max Units Conditions
Legend: Shading of rows is to assist in readability of the table.
Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to V
DD or VSS and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all I
DD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
DD or VSS;
MCLR
= VDD; WDT enabled/disabled as specified.
3: When operation below -10°C is expected, use T1OSC High-Power mode, where LPT1OSC (CONFIG3H<2>) = 0.
When operation will always be above -10°C, then the low-power Timer1 oscillator may be selected.
4: BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less
than the sum of both specifications.