Datasheet

 2010 Microchip Technology Inc. Preliminary DS41412C-page 431
PIC18(L)F2X/4XK22
27.5 DC Characteristics: Primary Run Supply Current, PIC18(L)F2X/4XK22
PIC18LF2X/4XK22 Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +125°C
PIC18F2X/4XK22 Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  T
A  +125°C
Param
No.
Device Characteristics Typ Max Units Conditions
D070 Supply Current (I
DD)
(1),(2)
0.07 0.14 mA -40°C to +125°C VDD = 1.8V FOSC = 1 MHz
(PRI_RUN,
EC oscillator)
D071
0.12 0.25 mA -40°C to +125°C V
DD = 3.0V
D072
0.08 0.20 mA -40°C to +125°C VDD = 1.8V
FOSC = 1 MHz
(PRI_RUN,
EC oscillator)
D073
0.13 0.25 mA -40°C to +125°C VDD = 3.0V
D074
0.15 0.30 mA -40°C to +125°C VDD = 5.0V
D075 1.2 2.0 mA -40°C to +125°C V
DD = 1.8V FOSC = 20 MHz
(PRI_RUN,
EC oscillator)
D076
2.2 3.8 mA -40°C to +125°C V
DD = 3.0V
D077
1.4 2.5 mA -40°C to +125°C VDD = 1.8V FOSC = 20 MHz
(PRI_RUN,
EC oscillator)
D078
2.4 4.0 mA -40°C to +125°C VDD = 3.0V
D079
2.7 4.5 mA -40°C to +125°C VDD = 5.0V
D080
6.5 11 mA -40°C to +125°C V
DD = 3.0V
F
OSC = 64 MHz
(PRI_RUN,
EC oscillator)
D081 6.8 11 mA -40°C to +125°C VDD = 3.0V FOSC = 64 MHz
(PRI_RUN,
EC oscillator)
D082
7.5 13 mA -40°C to +125°C VDD = 5.0V
D083 1.0 1.7 mA -40°C to +125°C V
DD = 1.8V FOSC = 4 MHz
16 MHz Internal
(PRI_RUN, EC +
PLL)
D084
1.8 3.2 mA -40°C to +125°C V
DD = 3.0V
D085
1.0 1.8 mA -40°C to +125°C VDD = 1.8V FOSC = 4 MHz
16 MHz Internal
(PRI_RUN, EC +
PLL)
D086
1.9 3.5 mA -40°C to +125°C VDD = 3.0V
D087
2.2 4.0 mA -40°C to +125°C VDD = 5.0V
D088
6.5 10 mA -40°C to +125°C V
DD = 3.0V
FOSC = 16 MHz
64 MHz Internal
(PRI_RUN, EC +
PLL)
Note 1: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as
I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temper-
ature, also have an impact on the current consumption.
The test conditions for all I
DD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to V
DD;
MCLR = VDD; WDT enabled/disabled as specified.
2: The test conditions for all I
DD measurements in active operation mode are:
All I/O pins set as outputs driven to VSS;
MCLR
= VDD;
OSC1 = external square wave, from rail-to-rail (PRI_RUN and PRI-IDLE only).