Datasheet

PIC18(L)F1XK22
DS40001365F-page 328  2009-2016 Microchip Technology Inc.
TABLE 26-4: PRIMARY RUN SUPPLY CURRENT
PIC18LF1XK22
Standard Operating Conditions (unless otherwise stated)
PIC18F1XK22
Standard Operating Conditions (unless otherwise stated)
Param.
No.
Device Characteristics Typ. Max. Units Conditions
D014
Supply Current (IDD)
(1, 2, 4, 5)
0.20 0.32 mA -40°C to +125°C VDD = 1.8V FOSC = 1 MHz
(PRI_RUN,
EC Med Osc)
D014A
0.27 0.39 mA -40°C to +125°C V
DD = 3.0V
D014 .20 .32 mA -40°C to +125°C VDD = 2.3V
FOSC = 1 MHz
(PRI_RUN,
EC Med Osc)
D014A
.27 .39 mA -40°C to +125°C VDD = 3.0V
D014B
.30 .42 mA -40°C to +125°C VDD = 5.0V
D015 1.7 2.6 mA -40°C to +125°C V
DD = 1.8V FOSC = 16 MHz
(PRI_RUN,
EC High Osc)
D015A
3.0 4.2 mA -40°C to +125°C V
DD = 3.0V
D015 2.4 3.2 mA -40°C to +125°C VDD = 2.3V
FOSC = 16 MHz
(PRI_RUN,
EC High Osc)
D015A
3.0 4.2 mA -40°C to +125°C VDD = 3.0V
D015B
3.3 4.4 mA -40°C to +125°C VDD = 5.0V
D016
11.5 14.0 mA -40°C to +125°C V
DD = 3.0V
F
OSC = 64 MHz
(PRI_RUN,
EC High Osc)
D016 11.9 14.4 mA -40°C to +125°C VDD = 2.3V FOSC = 64 MHz
(PRI_RUN,
EC High Osc)
D016A
12.1 14.6 mA -40°C to +125°C VDD = 5.0V
D017 2.1 2.9 mA -40°C to +125°C V
DD = 1.8V FOSC = 4 MHz
16 MHz Internal
(PRI_RUN HS+PLL)
D017A
3.1 4.0 mA -40°C to +125°C V
DD = 3.0V
D017 2.1 2.9 mA -40°C to +125°C VDD = 2.3V
FOSC = 4 MHz
16 MHz Internal
(PRI_RUN HS+PLL)
D017A
3.1 4.0 mA -40°C to +125°C VDD = 3.0V
D017B
3.3 4.5 mA -40°C to +125°C VDD = 5.0V
D018
10 15 mA -40°C to +125°C V
DD = 3.0V
F
OSC = 16 MHz
64 MHz Internal
(PRI_RUN HS+PLL)
D018 12.4 15.4 mA -40°C to +125°C VDD = 3.0V FOSC = 16 MHz
64 MHz Internal
(PRI_RUN HS+PLL)
D018A
12.6 15.6 mA -40°C to +125°C VDD = 5.0V
* These parameters are characterized but not tested.
Note 1: The test conditions for all I
DD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to V
DD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact
on the current consumption.
3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be
extended by the formula I
R = VDD/2REXT (mA) with REXT in k
4: FVR and BOR are disabled.
5: When a single temperature range is provided for a parameter, the specification applies to both industrial and extended
temperature devices.