Datasheet
PIC18(L)F1XK22
DS40001365F-page 326 2009-2016 Microchip Technology Inc.
TABLE 26-2: RC RUN SUPPLY CURRENT
PIC18LF1XK22
Standard Operating Conditions (unless otherwise stated)
PIC18F1XK22
Standard Operating Conditions (unless otherwise stated)
Param.
No.
Device Characteristics Typ. Max. Units Conditions
D008
Supply Current (I
DD)
(1, 2, 4, 5)
69A -40°C
V
DD = 1.8V
F
OSC = 31 kHz
(4)
(RC_RUN mode,
LFINTOSC source)
710A+25°C
814A+85°C
11 17 A +125°C
D008A 11 15 A -40°C
V
DD = 3.0V
12 16 A+25°C
13 25 A+85°C
17 28 A +125°C
D008 22 45 A -40°C
VDD = 2.3V
FOSC = 31 kHz
(4)
(RC_RUN mode,
LFINTOSC source)
23 48 A +25°C
25 50 A +85°C
28 55 A +125°C
D008A 25 50 A -40°C
VDD = 3.0V
27 55 A +25°C
30 60 A +85°C
32 75 A +125°C
D008B 30 55 A -40°C
VDD = 5.0V
33 60 A +25°C
37 65 A +85°C
40 80 A +125°C
D009 0.4 0.5 mA -40°C to +125°C V
DD = 1.8V FOSC = 1 MHz
(RC_RUN mode,
HFINTOSC source)
D009A 0.6 0.8 mA -40°C to +125°C V
DD = 3.0V
D009 0.45 0.55 mA -40°C to +125°C VDD = 2.3V
FOSC = 1 MHz
(RC_RUN mode,
HFINTOSC source)
D009A 0.60 0.82 mA -40°C to +125°C VDD = 3.0V
D009B 0.80 1.0 mA -40°C to +125°C VDD = 5.0V
D010
1.9
2.5
mA
-40°C to +125°C V
DD = 1.8V
F
OSC = 16 MHz
(RC_RUN mode,
HF-INTOSC source)
D010A
3.5
4.4
mA
-40°C to +125°C V
DD = 3.0V
D010
2.4
3.5
mA
-40°C to +125°C VDD = 2.3V
FOSC = 16 MHz
(RC_RUN mode,
HF-INTOSC source)
D010A
3.5
4.6
mA
-40°C to +125°C VDD = 3.0V
D010B
3.7
4.7
mA
-40°C to +125°C VDD = 5.0V
* These parameters are characterized but not tested.
Note 1: The test conditions for all I
DD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to V
DD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
3: For RC oscillator configurations, current through R
EXT is not included. The current through the resistor can be extended
by the formula I
R = VDD/2REXT (mA) with REXT in k
4: FVR and BOR are disabled.
5: When a single temperature range is provided for a parameter, the specification applies to both industrial and extended
temperature devices.